Yes they are easy to follow, it took me a couple of attempts but have updated my box, and just doing a scan now...
-
-
Instructions for loading the Kryptoview bin filr
Loading software to KRYPTViEW ArnEt
You will not get any channels until this part has been completed in FULL
WARNING
BEFORE FLASHING WITH THIS METHOD YOU MUST EXIT EASY INSTALLATION (PRESS MENU BUTTON ON THE REMOTE) AND GO INTO THE MENU/SYSTEM SETTINGS/OTHER SETTINGS AND SWITCH POWERSCAN MODE TO OFF!!!
OTHER WISE AS AN ALTERNATIVE METHOD SET UP THE LOADER WITH THE ARNET UNPLUGGED, START THE LOADER THEN PLUG IN THE POWER ON THE ARNET TO START THE FLASH. FUTURE FIRMWARE YOU MAY HAVE TO DO THIS ALL THE TIME
1. Using the RS232 (Null Modem) cable connect the box to the back of your computer.
2. Plug the KRYPTViEW ArnEt into the mains power supply.
3. Make sure The KRYPTViEW ArnEt displays 0000 on the front of the box. Or if you are updating from a working firmware with existing channels just make sure it's switched on (not standby).
4. Double click the KRYPTViEW ArnEt loader (it looks like a grey satellite dish).
5. The loader will open. Click the green download button. Another box will open saying Code Send. Click Open?
6. Click on KRYPTViEW SOFTWARE once, so it is highlighted. Then click the Open button. This file will now appear File box.
7. Click Start in the loader box then immediately press the RED button half way down the remote control TWICE, then the STANDBY button at the top left hand corner of the remote. (Red circle with a line at the top). So its START-RED-RED-STANDBY
The software will start downloading
The display on the front of the KRYPTViEW ArnEt will have a green line going round and round.
Wait until it says Download Success !
Congratulations you have now programmed your KRYPTViEW ArnEt
Now plug it into your TV, Choose your Provider and scan for channels. Then wait for it to update. It may take a few minutes or sometimes longer, up to an hour so please be patient. The EMU is enabled and there is no updating message.
JOB DONE!!!!
Hope this helps all those that need it.
Cheers
Comment
-
can any0ne please give me a step by step information on how to install the latest arnet cable box software....THANXComment
-
Hi there,
I'm thinking about getting one of these boxes. Is it really that easy to set up and recieve ALL the channels??
The reason i ask is because i have been offered one for ?100 which i thought was fair enough as i thought there was a "big" set up involved.
However if those instructions are anything to go by, i could do it with my eyes shut.
So should i buy one and try myself or pay the ?100?
Thanks in advance.
YannosComment
-
can anyone please help meComment
-
i am new to this updating software i have the RS232 an the rest bt need help on firmwareComment
-
your post number 19 has 2 posts above it both helping youComment
-
hi mate,
my kyrpt view box says waiting for code update,if i download this files in to the box is it going to work.please help.im new to these stuff and really confusedComment
-
is it easier for a newbie to input the keys manually????Comment
-
just to say that all channels back now after leaving box on over night. to all those looking for instructions, You have to have a little read around 1st before asking, its just the way, people will always help but as long as you have had a look yourself. in this thread are the instructions and step by step guides, you have to have a connection to the arnet box via a cable but its all simpleComment
-
Why o why cant i get this to work
followed all the instructions above exactly and still no joy. Any further advice before i take a bloody hammer to the thing 
.
Comment
-
thanxs
i have problem with my box hope this works..
Comment
-
hi i am haveing problem with downlod can u help pls
Comment
-
whats the new firmware for the arnet ?Comment
Comment