OPEN MEDIA condenser

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • EAMO 2
    DK Veteran
    • Nov 2008
    • 1201

    #1

    OPEN MEDIA condenser

    After flashing DK 1.1 to box it will not re-boot,tries to start & cuts out.
    Green light stays on,will not go to standby,green light flashes on prompt
    from remote but box does not respond.On inspection 25v 470 condenser
    was swollen.Replaced 470condenser of less volts; box started up fine,
    but condenser was too hot.After fitting new condenser [25v 470] box will
    not reboot.Similiar box took DK 1.1 flash & N2 fix and works fine NTL IRL
    Both boxes are new. any ideas welcome
  • max_gee
    V.I.P. Member
    • Apr 2008
    • 108

    #2
    Instead of opening the unit, why didnt you send it for for repair / replacement?

    Comment

    • EAMO 2
      DK Veteran
      • Nov 2008
      • 1201

      #3
      Originally posted by max_gee
      Instead of opening the unit, why didnt you send it for for repair / replacement?
      Had promised a mate a loan of a working box.He recently bought 2
      eurovox 5100 pvr boxes.They no longer work on NTL IRL.
      Told him he could have open media until fix arrives for his boxes.
      Have been told warranty is gone once you flash box

      Comment

      • on_the_jazz
        DK Veteran
        • Jul 2008
        • 557

        #4
        Please delete.
        Last edited by on_the_jazz; 5 July, 2009, 16:26.

        Comment

        • SatSearching
          V.I.P. Member
          • Apr 2008
          • 447

          #5
          I'm guessing this "Condenser" is an electrolitic capacitor (470mF)?

          Make sure you fit an exact same replacement (same voltage, farad and temperature rating) and get the polarity right (legs the right way round).

          Then try flashing again.

          SS


          Originally posted by EAMONN BRESLIN
          After flashing DK 1.1 to box it will not re-boot,tries to start & cuts out.
          Green light stays on,will not go to standby,green light flashes on prompt
          from remote but box does not respond.On inspection 25v 470 condenser
          was swollen.Replaced 470condenser of less volts; box started up fine,
          but condenser was too hot.After fitting new condenser [25v 470] box will
          not reboot.Similiar box took DK 1.1 flash & N2 fix and works fine NTL IRL
          Both boxes are new. any ideas welcome

          Comment

          • EAMO 2
            DK Veteran
            • Nov 2008
            • 1201

            #6
            Originally posted by SatSearching
            I'm guessing this "Condenser" is an electrolitic capacitor (470mF)?

            Make sure you fit an exact same replacement (same voltage, farad and temperature rating) and get the polarity right (legs the right way round).

            Then try flashing again.

            SS
            I got box to re-boot on SAT side ; fact reset, flashed with DK 1.1
            I now have :
            Cable side--- box tries to re-boot,cuts out after 5-10 seconds
            AV output dies. Tries to re-boot every 30 seconds.
            SAT side---- green light stuck,box doesn't cut out, AV output holds
            blank screen, like D-box in de-bug mode.
            Have used HALLENBERG IFA on several D-boxes 1&2 chip
            It connected every time & flashed boxes in under 10 mins
            HYperterminal IFA takes 90 mins+ & doesn't always work.
            IF I could get a HALLENBERG type IFA for dream I'd be in with a shout.
            Have used DK 1.1 on other O.M no problem.
            The replacement capacitor is correct V & yF
            Temp rating is +105*C.I will have to check orig. temp rating
            Polarity is surely right as CAP has one long & one short leg
            Hope this will help you to help me, thanks for your time

            Comment

            Working...