new VU+

[fionn]

I'm having problems with DCC as I cannot log in. I input the IP address and that part is ok but I cannot get telnet to work.It keess telling wrong log in.DCC was set up for DM 800 with "root" and dreambox".Is there a default for Vu+.
Thanks.

[MrFug]

Taken from another source

"ok.. DCC needs a password to work ..

Dreambox comes with the default username : "root".. password: "dreambox"

The Vu+ is a little different.. Username : "root".. There is no default password but you will have to set one before you can access your Vu+ in ftp..

Here are the instructions on what to do to get your password..

Open DCC and as normal make sure all ip`s are correct...
Clear the password in box provided
Press reconnect
Go to telnet
Type "passwd"
You will now be asked for new password.. type your new password.. Then enter..
You will be asked to retype your new password.. then enter.. and the letters you type may not show up.. but all is OK
Confirmed
Now go to configuration page and click on reconnect.

thats all there is to it... you should now be able to access all the setting on your box..

Hope this helps .. "

[fionn]

Thanks but unfortunately that won't work either.

[andymc1s]

I had the same problem but only with some images, I am using an open pli image now with no problem.
openpli-1.0-2010-09-06.

[dell_xps]

Open up network on your PC or Mac, you can access it via that.
Just transfer stuff across, what image are you using ?

[fionn]

I bought with blackhole image installed but I cannot input lines as I cannot get telenet/ftp to work.Never had any problems with my dm800.
How to I input cline thru network.Thanks.

[lgpaul]

Try total commander as you ftp client. The password could be vuduo or vuplus

[wilf]

look for a fully loaded image they are much easier, cccam + config already installed and there should be the log in password with the download, just change it to whatever you want afterwards,
ps and give thanks if you can to the person who uploaded it as they have done the hard work.

[lincsat]

I bought with blackhole image installed but I cannot input lines as I cannot get telenet/ftp to work.Never had any problems with my dm800.
How to I input cline thru network.Thanks.

I use FlashFXP with username=root, password leave blank. You get another box pop-up asking for password, leave that blank as well.

[fionn]

Same problems using CUTEftp.Before I upload a new image do I need to do factory restore first?.Thanks

[lincsat]

I would use the backup script before uploading a new image, then you have a fallback if all else fails.

[dell_xps]

Get team Vix image on it, any probs just ask, apart from ccam etc :-)

[fionn]

Loaded Pli and tried to set password for DCC and dcc hung and cannot do it again.Dont know what is the problem.Loading VTI image now and have a new question.Can I ftp to Receiver without setting a password using cute or some other ftp?All i want is input my cline.
Thanks.

Vix already downloaded for future trial.

[dell_xps]

Look on your PC, go to network, VUDuo will show up in there, no need for FTP clients.
If you use a mac look in finder, shows up in there.
Forgot to mention make sure ethernet is plugged in to box and router !!

[fionn]

Getting there...VTI loaded but scracthing my head about installing ccam 2.21.Where do the files go?It was so easy when you could get the cams from the panels.Alas..
c'mon guys help(Idiots guide)

P.S The initial problem I had was because I bought the unit with B'Hole installed and they input the password for telenet but did not think to tell me> Spent a whole night being driven daft by"invalid login"