Spiderbox 7000HD

[blueflash234]

mate i have the 7000 and if i was doing it again i would get the 9000 mainly because you have 2 ci slots you never know when you may have to buy a viewing card

[gez007]

Hi there I have a spiderbox 9000 and when digitalb changed from16e to the other one they stopped working.Is there any chaqnce of downloadin a software to get my chanells.I have just joined you and I dont think I will be allowed to download anything yet.Can you please give me some advice.thank you

[dick b]

Digitalb on 16E W3C transponders are now 10.803 H,10.762 H,& 10.845 H all 27500 you can add these in the manual scan menu,but if your box is over 1yr old you have probably been cut off from the server check in "network" that ethernet is connect and not showing error code(0)

[dragon123]

Hi done all you said as below now i can get some channels but a lot is scrambled, believe i need cams installed how and where can i get some or whatever needed installed thanks in advance, sorry for being away along time as computers beed idol (broken LOL)[Q UOTE=dick b;1303688]connect box up to dish/tv/broadband.
(1) do factory reset
(2)load patch I"m sending Software only
(3) factory reset again
(4)menu>network press 1111 on h/set,turn network and ethernet on and register
(5)load a channel list or scan (you can use the one I"v sent but it may not suit)
(6)enter your long/lat and display timeouts etc
(7)go to key edit turn ucas & ucas auto roll on
(8)re-set key data and load softcam I"m sending.

any probs just ask there is still a lot of channels open on these boxes on ethernet as well as via ucas/softcam as said digitalb is the most stable on ethernet but stuff on 0.8 West is pretty good too as well as 13E xxx stuff.STB_DB is the channel list[/QUOTE]

[dick b]

sorry mate that post of mine your quoting is out of date .ethernet is closed for boxes over 1yr old now. but softcams are still available if you look on the right site.

[bcogh50]

Hi I just bought a 7000hd from a satellite shop. I was wondering if someone could let me know what I should download to get it working to it's best. I have been reading the threads which are very helpful thanks. I would contact the satellite shop but they are now finished until after Xmas...typical . Any help would be greatly appreciated.

[5bellies]

I found this elsewhere:

FM hardware boxes - NOT WORKING - error code (0)

RM hardware boxes - WORKING- login says CONNECTED

You can check which Hardware version your receiver is in System Information Menu

[ramjet]

Hi I just bought a 7000hd from a satellite shop. I was wondering if someone could let me know what I should download to get it working to it's best. I have been reading the threads which are very helpful thanks. I would contact the satellite shop but they are now finished until after Xmas...typical . Any help would be greatly appreciated.

stick the 15 nov 2011 patch on it after a fact reset and fact reset yet again , then a channel list , turn on networking using 1111 code on network , now sort out ip address from router , turn on ETHERNET so it says CONNECTED , turn on both ucas in keyedit above network , add HDsoftcam , input usals if on a motor

that should do it for now , unless you have any N or C lines to add

[noorani]

thank you guys for your posts

[ramjet]

mate i have the 7000 and if i was doing it again i would get the 9000 mainly because you have 2 ci slots you never know when you may have to buy a viewing card

CI slots are common interface slots and are for cams not cards

CA slots are for cards (Conditional Access) and all the spider boxes have a CA slot , my 7000 has a card in it as I type this message

[del_]

Hi All, I'm no expert and not a newbie as such. I've followed the Starview HD Combo, Blade BM7000 and now I have acquired a Wiztech 9555 HD Ci. A comment I read in the forum suggested that it was a Twin Tuner Spider? My question therefore is can this be infused with that firmware or can anybody update me on a possible source for a loader? Thanks in Advance (TIA)