protek packages

[jpr]

I have the protek 9600 ip. I havent used it in a while and now notting opens. Does anyone know what packages are opening on it these days.

[martin-f]

google nanoxx forum for info m8

[.: JaCkPoT :.]

I have the protek 9600 ip. I havent used it in a while and now notting opens. Does anyone know what packages are opening on it these days.

all the irdeto packages are gone. (i believe so)

[mdt]

protek/nanoxx and maxx1000

there are 14 packages open at this time.

[ALAN 1]

MDT mate, correction there is 15 not 14 look on onlinelist .

[jpr]

Were can i go online to see a list of packages that are open.

[jpr]

Its ok i found the list. I havent used the protek in a few months too busy with the dreambox. when i turn it to one of the channels thats open it says internet off. I have newcamd set to off , i think thats right. My broadband is ok. Any help would be great.

[mdt]

packages

my mistake alan1, i stand corrected!

[ALAN 1]

thats ok, Cheers mate.

[martin-f]

theres 16 using keys

[cactikid]

i was led to believe nanoxx and protek differed even though they are similar,are there more than one servers for protek as suppliers told me they cant update because their servers are down.

[martin-f]

protek and nanoxx are spade for spade the f/w is the same the remote works from one to the other etc
yes there is more than one server google pinsat you will need google translate unless you can read arabic

the server that i use is not down all is working fine

[martin-f]

Its ok i found the list. I havent used the protek in a few months too busy with the dreambox. when i turn it to one of the channels thats open it says internet off. I have newcamd set to off , i think thats right. My broadband is ok. Any help would be great.

you will have to update your f/w m8 you need to press the blue button or menu to check to get it to work you will need to install below

google nanoxx forum all files and info there

bt:134 sw:t 59 k:19

[jpr]

How do i put the new software into the protek do i need a loader. I have never done it before.

[martin-f]

mods if there is any of this is breaking any rules please remove

this is not my work thanks to the author


Loading & Setting up Software REV29(10-9-2009)

This setup is for Protek 9600ip, NonoXX 9600ip and some Maxx 1000 receivers.

CONTENTS

1 NEW OUT OF THE BOX (NEW RECEIVER)
2 SETUP INFORMATION
3 UPLOADER V1.3
4 LOADING BOOT, SOFTWARE OR KEYS.
5 AUTO UPDATE CHECK
6 S/W UPGRADE feature
7 OPERATING NOTES
8 WEBLOADER
9 PROBLEMS
10 DOWNLOADING KEY/SOFTWARE PROBLEMS
11 MANUAL KEY ENTRY



1 NEW OUT OF THE BOX (NEW RECEIVER)

You will need to connect you box to your router using a straight, not crossover RJ45 patch Ethernet cable. (It is possible to purchase separate wireless devices).

Connect your dish set up to LNB in.

Connect to your TV.

It would be unusual to find the latest software installed out of the box.

Don?t spend time looking though the menu structure, setting up your dish configuration or scanning in channels, you will need to do it all again when the latest software is installed.

Check the current BT (Boot) and SW (Software) by pressing EXIT then the MEMU button. If it reads BT: 1.33 or 1.34 the BT is OK. If BT is not 1.33 or 1.34 you will need to install it. If the SW reads SW: v1.xx where xx is two digits then this is the original software and need to be updated with the latest software.

The original software installed in new receivers does not support AUTO UPDATE CHECK, S/W UPGRADE or Webloader features.

To install BT or latest software you will need to connect a RS232 Null modem cable between your box and PC. If your PC hasn?t got a RS232 port you will need a USB to RS232 adapter. Goto the section UPLOADER v1.3 and then return to this point.

After loading the latest software use down arrow to select SYSTEM SETTINGS, press OK, then use the down arrow to select FACTORY DEFAULTS and press OK. Enter PARENTAL CONTROL PASSWORD (Default 0000) and press OK.

Do all the usual things you do with a satellite receiver.

Follow the user manual.

Enter the settings under MENU ? INSTALLATION - ANTENNA SETTING. You need to make these settings for each satellite you intend to scan. If you are using a motor on your dish that support USALS then I recommend you use this rather than DiSEqC 1.2 as the manual movements are not fine enough to get a good signal without lots of work. If your dish system is set up correctly the USALS will give exultant results. Don?t forget to set correct longitude and latitude under MOTOR SETTINGS.

Now scan in the satellites you require using MENU - CHANNEL SEARCH. Select the satellite by pressing OK on SATELLITE. Select the required satellite and press OK. Set SCAN OPTIONS to TV ONLY (saves space) and SEARCH CHANNELS to NETWORK SEARCH (adds new transponders) and press OK. After saving the scanned channels for each satellite use the EXIT key to exit the menu structure before going back in to scan another satellite. If you don?t do this you may loose the channels you have saved. I don?t recommend using the MULTI SAT SEARCH FEATURE as again channels do not always store.


2 SETUP INFORMATION

The Box should have Boot BT:1.33 or BT:1.34.

Always load the latest software, the two bin files.


If you press MENU ? INTERNET and only 4 options are available you need to press EXIT and then press Menu 8888 to activate all the menus. Select INTERNET again there should now be 6 options.

Under MENU - INTERNET set the following:-

NETWORK CONNECTION ON

AUTO UPDATE CHECK ON (T59 or later software only. Each time you turn on your box it will check to see if new software and/or keys are available, if they are read the onscreen information and select UPDATE to update)

Under NETWORK INFORMATION set
DHCP/STATIC to DHCP (If IP address is all zeros set to static then back to DHCP, IP ADDRESS, SUBNET MASK and GATEWAY address should fill in automatically) PVR server IP address is your PC IP address but is only used if your are running the record to PC Hard disk software.

NEWCAMD is normally set to OFF.

Under PROXY CONNECTION set PROXY CONNECTION to OFF.

S/W UPGRADE, go to S/W UPGRADE section to make this setting and use this feature.

When watching a channel press the MENU button to confirm BT, SW, and K.

Whilst on a channel press OK, then BLUE button, for further information.


3 UPLOADER V1.3

Loading BT or assuming you current software does not support the AUTO UPDATE CHECK, S/W UPGRADE or webloader for loading bin files, you will need software UPLOADER V1.3. Download the required files from Protek software section on this site and uncompress the Zip files. Connect RS232 Null modem cable to box and PC with box off at mains. If your PC hasn?t got a RS232 port you will need a USB to RS232 adapter.

Run Uploader software.

Select correct COM port by clicking on com1:115200.

If loading BT select BOOT by clicking on MAIN, for software bin files leave at MAIN.

Select OPEN FILE and browse to Boot software bin file or other software bin files as required, Click OPEN.

Click on START DOWNLOAD

Click OK on the reboot message.

A blank box will appear, then switch on your receiver. The blank box will fill in showing the software has connected to the receiver.

The % bar should start to count up to 100.

Looking at the box display it should mirror this count.

When the count reaches 100 on the bar a message will appear underneath stating ?Transferring_complete Press OK (several sec to write)?

Press OK. The message will change to ?Downloading has been completed?

The display on the box once it has reached 100 will change to ?hold?, then after a delay 5 to 20 seconds to ?900d?, then ?0000?

You have successfully loaded the software.



4 LOADING BOOT or SOFTWARE BIN FILES.

If you wish to load BT, boot software or your current software does not support AUTO UPDATE CHECK or S/W UPGRADE or Webloader features, see USING UPLOADER VERSION 1.3 in the section above. The Uploader can also be useful if for some reason you are having problems with the AUTO UPDATE CHECK feature, or S/W UPGRADE or Webloader. AUTO UPDATE CHECK feature followed by the S/W UPGRADE and Webloader are the easiest ways to load software bin files,. BT boot software MUST be loaded using the Uploader v1.3.

5 AUTO UPDATE CHECK

With AUTO UPDATE CHECK set to ON.
Every time you turn on your box it will check for new software and keys. If it detects that that new files are available an on screen message will appear providing information on the update that is available. Select UPDATE to perform an auto update. If the download persistently fails you will have to load the software using the Webloader or uploader v1.3.


6 S/W UPGRADE feature (If for any reason you do not wish to use AUTO UPDATE CHECK)

LOADING KEYS

Press MENU ? INTERNET ? S/W UPGRADE

You can use FILE 1 DOWNLOAD to download keys. Press OK and enter the following address

xvision.skynolimit.com/key/kxx.bin where xx is the latest key number.

The http:// is automatically filled in. Press the RED button to start the download. The box will reboot automatically at the end of the download.

LOADING SOFTWARE

Press MENU ? INTERNET ? S/W UPGRADE

You can use FILE 2 DOWNLOAD to download software. Press OK and enter the following address

xvision.skynolimit.com/key/xxx.bin where xxx is the latest software version.

The http:// is automatically filled in. Press the RED button to start the download. The box will reboot automatically at the end of the download.
If the download persistently fails you will have to load the software using the Webloader or uploader v1.3.



7 OPERATING NOTES

The BT, SW and K can be checked by pressing the menu button.

Whilst on a channel press OK, then BLUE button, for further information.

Also check

[url=http://www.xvision.skynolimit.com/nanoxx/onlinelist/Output.php]Onlinelist[/url]

8 WEBLOADER

Webloader is a feature that let you download bin files except BT files without using a RS232 cable.

You don't need any software for this, just open an internet browser on a PC and enter the IP address of the receiver, found under MENU ? INTERNET ? NETWORK INFORMATION ?IP ADDRESS e.g. 192.168.0.4 where you would normally enter www. etc in you PC. Do not enter any leading zeros. Thus 192.168.000.004 becomes 192.168.0.4 Note DHCP/STATIC must be set to DHCP so IP address files in automatically.

Click go on your internet browser and a dialogue box should then open and ask for a username and password. The default username is admin and the PARENTAL CONTROL PASSWORD (Default 0000). Once these have been entered, you can browse to the bin files you want to upload. Channels list, digital.bin file can also be uploaded to the receiver.

You can download your channel list using CHANNEL BACKUP to give a file called chdata.bin. This file backs up your channel list plus other settings. The file on my PC comes out as chdata.zip and I have to change the extension from zip to bin. Open the chdata.bin file in the channel editor V1.6 (available from the Protek software section) and then save it as a backup file, digital.bin. If for some reason the file won?t open, delete both files and try again. It?s a good idea to check your favourite lists, if they look wrong delete the files and try again. If needed, you can then download digital.bin using webloader to restore your channel list and other settings.

Before attempting to restore your channel list perform a FACTORY DEFAULT (reset) under MENU ? SYSTEM SETTINGS. Also under MENU ? INTERNET- NETWORK INFORMATION set DHCP to STATIC then back to DHCP. Connect using the webloader and download the channel list as described above. After the download check your INTERNET settings under MENU and check ANTENNA SETTINGS under MENU ? INSTALLATION, including Longitude and Latitude, if using USALS, under MOTOR SETTING.

You can use the channel editor to make changes. Always keep a copy of the original channel list in case the one you are editing goes wrong or strange things happen when you load it back to your box. The editor is not perfect and can mess things up.


9 PROBLEMS


If you have problems, need further information, read on.

If you press MENU ? INTERNET and only 4 options are available you need to press EXIT and then press Menu 8888 to activate all the menus . Select INTERNET there should now be 6 options.

Under MENU - INTERNET

AUTO UPDATE CHECK ON (T59 or later software only. Each time you turn on your box it will check to see if new software and/or keys are available, if they are read the onscreen information and select UPDATE to update)

Under NETWORK INFORMATION set
DHCP/STATIC to DHCP ( If IP address is all zeros set to static then back to DHCP, IP ADDRESS, SUBNET MASK and GATEWAY address should fill in automatically) PVR server IP address is your PC IP address but is only used if your are running the record to PC Hard disk software.

NEWCAMD is normally set to OFF.

Under PROXY CONNECTION set PROXY CONNECTION to OFF.

S/W UPGRADE, go to S/W UPGRADE feature section to check this setting.


10 DOWNLOADING KEY/SOFTWARE PROBLEMS

Some people seem to have a problem with downloading keys and or software using AUTO UPDATE CHECK or S/W Upgrade feature. For them try putting this address in your PC internet explorer, you should then be asked to save the file. The bin file can then be downloaded to the box using the webloader or Uploader V1.3.

Keys

[url]http://xvision.skynolimit.com/key/k19.bin[/url]

Software

[url]http://xvision.skynolimit.com/key/t59.bin[/url]

11 MANUAL KEY ENTRY

If you loose RCS Digi TV first download a fresh copy of the latest key file. When RCS Digi TV changes its key the current key file is normally updated with out changing the key number.

If for any reason the RCS Digi TV keys are out of date in the latest key file here?s how to enter them manually.

On a Digi TV channels say DigiFilms 1 12607H2700 press the YELLOW key.

The Nagra key menu should appear with the key line you need to enter highlighted.

Note this gives PP as 2111 key 00 lines 00 and 01 key 01 lines 02 and 03
Press OK followed by the red key twice. Now enter the first eight two digit keys.

Then press MENU key.

Move the curser down one line with down arrow.

Press OK followed by the RED key twice. Now enter the second eight two digit keys.

Then press the MENU key.

To exit the Nagra menu and save the keys you just entered press the EXIT key (not the MENU key).

With Newcamd set to OFF channels should open.

GOOD LUCK

Note: Viewing Pay TV without a valid subscription may be illegal!
All information given is for experimental and educational purposes only!