Diablo 2 (3.9) and cas 3 help required

[wijnendael]

Hi all, joined this forum hoping for better success on replies that i am encountering on others i have tried for information.
Long time since i did anything with satellite cams and cards so very rusty and need help to get going again.
I have just got myself a diablo 2 rev 3.9 cam and cas 3 but not having much sucess with the programming. I have loaded the ipnosys 019 file and have finally got the bis channels to open but nothing else. I read on this forum somewhere (cannot find it anymore) that with this file you must also update the digi tv keys but i really have no clue as to what i need to do for this. If somebody can give me some friendly advice on what to do with this cam to get it working i would be grateful. Which files and keys are currently correct ? and possibly a link to how you update keys etc

[benny/9]

Hi all, joined this forum hoping for better success on replies that i am encountering on others i have tried for information.
Long time since i did anything with satellite cams and cards so very rusty and need help to get going again.
I have just got myself a diablo 2 rev 3.9 cam and cas 3 but not having much sucess with the programming. I have loaded the ipnosys 019 file and have finally got the bis channels to open but nothing else. I read on this forum somewhere (cannot find it anymore) that with this file you must also update the digi tv keys but i really have no clue as to what i need to do for this. If somebody can give me some friendly advice on what to do with this cam to get it working i would be grateful. Which files and keys are currently correct ? and possibly a link to how you update keys etc

************************************************** ****
here's a bit of info that might help you mate,
you need to load the key bin files when the keys change
*********************************
how to load the key bin file on a diablo cam [all versions of cam]
***************************
You may want to load the the latest [key bin] once you have loaded the file. if the keys have changed or are out of date. you use [tab 2] on Cas3 8.7.1 studio software for this [Cam file System]. Press the connect button at the top of the right hand pane. Once it has connected to the cam - you will see the existing Keys.bin in that first window. Then go to the top left pane and open the folder where your new unzipped key.bin file is located on your computer. You will now see your new key bin in the bottom left pane. Highlight the file and press the top green arrow to move it across. Just write over the top of the existing one when the software asks. There is no need to remove the old one first. Make sure the new file is unzipped before you load the file.
************************************************** *******
Reformatting The Cam
*****************
There are occassions when the cam will benefit from being re-formatted for a fresh start. Such instances are the following :-----------
You have loaded a new underworld file - then you can't access the cam menu. Although, you should always try to go this while on a FTA channel. Any changes made to the configuration menu - require's the cam to be re-booted, [ie: turn the receiver off and on] while the cam is in the receiver ci slot, for any changes made take effect. The cam is not opening the current channels available - after loading the latest files. The pictures are glitching or freezing on a channel that worked normally before.
***********************************************
to re-format the cam, Go to [tab 3] on the Cas Studio software - named Cam Disk Functions and simply press the button marked Format. A box will then appear while the format takes place - and will indicate when it has finished. This operation takes about two minutes.Once the format is complete - load the correct file for your cam and if needed the latest keys bin as stated in the above post.after you format the cam and re-load the file the cam configuration will be lost and need to be re-configured to get the channels to open.It is not necessary to format the cam everytime you update the file. Writing over the top of the previous version is usually fine - and does not change the cam config settings.
***************************************
how to set the cam config settings
**************************
put the cam in the receiver slot and turn on
press menu and>go to common interface and you will
see the file name ie: ipnosys 019 highlight it
and click>ok on the next panel go to [4] configuration
and click>ok on the next panel set the configuration
to the following settings useing you vol and chn buttons
on your remote to scroll and change the menu's
************************************************
[1] language [english]
[2] caids file [caids]
[3] PMT - [on]
[4] emulators [on]
[5] N2 AU [on]
[6] Emu priority [1:emu-2:cards] unless your useing a card in the cam
[7] fixed cw [on]
[8] Smartcard mess [show never]
[9] adminstrator menu [ do not change anything in this ]

[mcs]

D2 & settings

N2 AU OFF recommended. If ON, not working correctly.
New ipnosys 021 has been released, but I can't upload it here.

[roxy90]

[QUOTE=benny/9;654040]************************************************** ****
here's a bit of info that might help you mate,
you need to load the key bin files when the keys change
*********************************
how to load the key bin file on a diablo cam [all versions of cam]
***************************
You may want to load the the latest [key bin] once you have loaded the file. if the keys have changed or are out of date. you use [tab 2] on Cas3 8.7.1 studio software for this [Cam file System]. Press the connect button at the top of the right hand pane. Once it has connected to the cam - you will see the existing Keys.bin in that first window. Then go to the top left pane and open the folder where your new unzipped key.bin file is located on your computer. You will now see your new key bin in the bottom left pane. Highlight the file and press the top green arrow to move it across. Just write over the top of the existing one when the software asks. There is no need to remove the old one first. Make sure the new file is unzipped before you load the file.
************************************************** *******
Reformatting The Cam
*****************
There are occassions when the cam will benefit from being re-formatted for a fresh start. Such instances are the following :-----------
You have loaded a new underworld file - then you can't access the cam menu. Although, you should always try to go ........................


thanks so much for your instructions!