Issues with emu

[martin20009]

Hi all, I've flashed my cuberevo with NLB-11102. The problem i have is with the emu. Im using it with cable and mgcamd so I copied my k*ys from my dbox into the k*ys folder. I pressed the green button and mgcamd is running but im still only getting fta channels. IOve been at this for days reading but I really not sure what im dong.

Thanks in advance

[aftermath]

did you chmod all the files to 755, the ones you transfered from dbox. ?

also go to var/keys/mg_cfg

right click , then edit

scroll down to here ..

# box type
# 00 autodetect, change only if you think wrong type detected.
# 01 dbox2
# 02 dreambox
# 03 triple-dragon
# 04 relook
# 05 openbox
B: { 11 }

B: { 11 } for E2
B: { 00 } for DGS based image , sometimes you might have to try { 12 }

[martin20009]

No I didn't chmod them. I just did what would do with my dbox or azbox. I forgot to mention that when I ftp'd these to my azbox they worked ok. I wil follow ur advice and report back. Thanks

[martin20009]

I had a look at the var/keys/mg_cfg file and it was set to 12. So I changed it too 00 and reset the cam still same. So I changed the file with the 1 from my dbox and chmod all files to 755 reset cam and seemdtoo be working till i rebooted it and now back to fta.

[aftermath]

re install mgcam 1.33

the dbox one will be written in different code to sh4 code

after installation reboot the box , then change the cam to a different one to mgcamd, say incubuscam for argument sake.

when you edit the mg_cfg file, chmod it 755, then re boot the box.

then go into NLB panel again and change the working cam to mgcamd.

I take it you put the

Nagraroms, autoroll.key, softcam.key,autoupdate.key

all those into var/keys and chmod 755 ?

# EMM messages
# 00 don't show any EMMs (default)
# 01 show only valid EMMs
# 02 show valid and bad EMMs with complete data display
M: { 00 }

# ECM messages
# 00 don't show anything about ecm
# 01 normal mode, show pids processed, decoded ecm and cw
# 02 verbose mode, show valid and bad ECMs with data
C: { 00 }

# AU
# 00 disable, no emm pids processed
# 01 enable, emm pids always processed for soft-au and shared cards
# 02 auto, emm started only if channel cant be decoded
# 03 process emm pids for network cards update only
A: { 02 }

# key update (sum 01 or 02 with 04)
# 01 update only new keys, default setting
# 02 update all keys (used for valid PMK checking)
# 04 enable TPS au
U: { 01 }

# config files folder (softcam, autoroll, ignore/priority)
# 00 files in /var/keys
# 01 files in /tmp
T: { 00 }

# network mode, use summ for several clients
# 00 no network (default)
# 01 newcamd netclient
# 02 radegast netclient
# 04 camd3 netclient
# 08 gbox netclient
G: { 09 }

# network retry, use summ for several options
# 00 disable
# 01 retry every new ecm
# 02 try to connect to offline shares every Q: seconds
# 04 try to detect and fast reconnect to lost (and not used atm) server
# + XX messages number and YY seconds to reconnect
# mg will reconnect to server, if no answer to last XX ecm/keepalive or
# if no answer for last ecm or keepalive sent for YY seconds
# set to 0 to disable
N: { 07 } 5 30

# network ecm timeout in seconds
K: { 05 }

# newcamd dead routes connect retry, sec
Q: { 600 }

# network shares priority
# 00 gbox, newcamd, radegast, camd3 (default)
# 01 camd3, radegast, newcamd, gbox
# 02 newcamd, camd3, gbox, radegast
P: { 02 }

# on screen display type
# 00 No OSD (default)
# 01 neutrino
# 02 enigma
# 03 relook
# + user password for http auth
O: { 00 } username password

# on screen display Options, summ of:
# 01 show emu ecm
# 02 show network shares messages
# 04 show decoding failed / fta
# 08 show emm keys update
# + web port to use for osd
S: { 03 } 80

# Log option, summ of:
# 00 off
# 01 network udp log
# 02 log to console
# 04 file, appended ! delete it by yourself, before it eat all your hdd
# + IP udp-port log-file-name
L: { 03 } 172.16.1.1 28007 /tmp/mgcamd.log

# keep ecm cache, seconds
# every cache entry takes 28 bytes, so 24h cache will take *only* 240-400kb of memory,
# for openbox/elanvision users with remote shares make sense to set it higher than default value,
# to not hammer cards while timeshifting or playing crypted recordings.
E: { 15 }

# cache option, summ of:
# 00 Off (default)
# 01 Ecm pids cache, store pids used to decode in /tmp/ca_cache.list at exit, load at startup, same syntax as restore.list
# 02 Ecm data cache, remember CW for (E time
# 04 Emm cache for network cards, do not resend the same emm twice, cache not cleared until restart
H: { 06 }

# reread files, summ of:
# 00 No (default)
# 01 reread config file on channel change (including priority and ignore, but not replace/cache)
# 02 reread SoftCam.Key on channel change
# 04 reread SoftCam.Key if file changed
R: { 00 }

# debug, summ of
# 00 off (default)
# 01 debug ecm
# 02 debug emm
# 04 debug network ecm
# 08 debug network emm
# 16 debug network login
# 32 show mem/cpu stats every 1 min
# 64 add timestamp to log messages
D: { 00 }

# box type
# 00 autodetect, change only if you think wrong type detected.
# 01 dbox2
# 02 dreambox
# 03 triple-dragon
# 04 relook
# 05 openbox
# 12 fortrex (ipboxhd)
B: { 12 }

[martin20009]

Thanks Aftermath, Ive tried everything. I even reflashed it a couple of times. I did Chmood to 755 and all the files i put into keys. I been at all afternoon so I give up. Im gonna have another go later but wonder is this image ok or is there another i could try?

Thanks again

[aftermath]

wait a few days m8. DGS just released their latest image, so NLB one will be out soon

[martin20009]

Just a quick update, I have now got it sorted all working. The problem was down to me thinking Dbox.

I'm little confused about something else though. My bereave came with image r11453 and I upgraded it to the latest r11502 without hitch. Now when I tried the sifteam versions of these its just hangs displaying booting. I did use flash tools via usb with all 3 images but I'm confused why.

Thanks