How to watch pay channels with Protek 9600 IP

[cactikid]

Protek 9600IP is now dead

dead as in what way?if firmware is not current it may not work as every now and again it may need a manual null modem update.

[mdt]

Protek 9600IP is now dead

THEY ARE NOT DEAD!!, as ive wrote elswhere on the forum you will need a id file for your box to get all your packages back. regards mdt

[sharraf]

Hi, It will be appreciated if you explain how to get the ID file and from where..regards

[mmoo]

MAXX 1000 receiver boxes

I wander if scrambled channels could still accessed with the Maxx1000 boxes? Can someone put me in the picture please, thanks in advance

[Burnmasterb]

Hello i need the uploader v13.
Who can me give it

Thanx

[ponho]

9600ip

good
dear colleagues not soft to the cccam

[abasia]

Thanx mate
i had aljazeera sport befor bu they disapear and i cnt dowloand the files. where can i find them to flash my ip9600.
regards

[kissedindevon]

help!!

How to load software to 9600IP

Firstly you will need the following tools:-

PC running Windows, which has an available serial (COM) port. If it does not have a COM port, you will need a USB to serial adapter

Null modem cable (also known as a crossover cable), with 9 pin D-connectors on end (female)

Download the following from the Downloadcenter:-
Click Here

Uploader v13
Bootloader 1.34
Software BorisT53


Please note: If your receiver is already flashed you don't need install those files. All you need to do is a internet connection and you are ready to go.

To open the files, you will need to have Winzip on the PC to extract the achived files. Make sure you extract all the files to a known folder, before starting.


Load bootloader on to receiver

Run UploaderV13.exe
Select the available COM port by clicking on COM1 (if this is not the COM port to be used).
Select Boot option, by click in on Main (this toggles between Main and Boot)
Click on Open File, and select the bootloader bin file
Click on Start Down
Click on OK on screen
Press OK on receiver
Press standby ***8211; the receiver will boot and the file will start transferring to the receiver
WAIT! - click OK on loader screen when told that transfer is complete
Press Exit on screen
Software is updated


Load software on to receiver - NOTE you can also use webloader for this function (read below)

Run UploaderV13.exe again, and select the COM port to use
This time, make sure that Main is selected, and not boot
Click on Open File, and select the software bin file
Click on Start Down
Click on OK on screen
Press OK on receiver
Press standby ***8211; the receiver will boot and the file will start transferring to the receiver
WAIT! - click OK on loader screen when told that transfer is complete
Press Exit on screen
Software is updated


To load channel list - NOTE you can also use webloader for this function (read below)

Run Uploader
Click on ***8220;Open File***8221;
Choose channel list file
Press Open
Click on ***8220;Start Down***8221;
Click on OK on screen
Press OK on receiver
Press standby ***8211; the receiver will boot and the file will start transferring to the receiver
Press Exit on screen
Channel list is updated

Once you have upgraded the s/w. Connect the antenna connection, and go into Menu, Installations to set up the antenna.


Set up Diseqc motor

Press Menu on the remote
Installation
Antenna Setting
Satellite - Choose satellite (press OK)
Changed Disqec1.2 to ON
Select Diseqc1.2 settings
Used left and right to move dish East / West for max signal / quality
Select Store Position - press OK
Press Exit

Job done

Follow same process for other satellites


If you have loaded the channel list from the Downloads / Settings section, you should have channels already loaded. If you want to choose pre-sorted channels, select FAV on the remote control.


Webloader

Once the bootloader is on the receiver, loading of software, keyfiles and channel lists can be achieved using the webloader function. You don't need any software for this, just open a browser on a PC on the same LAN as the receiver (IE, Firefox, Opera, Chrome, etc), and enter the IP address of the receiver, i.e. 192.160.1.6

This will then ask for a username and password. The default username is admin, and the default password is 0000. Once these have been entered, you can browse to the files you want to upload, and then send them to the receiver via your LAN

You can use Webloader to load software, keyfiles or channel lists, but not bootloader (which needs to be added via Uploader V13

Once the files has been uploaded to the receiver, please wait while it automatically reboots

More info at>>>>>> NanoXX Support Forum • Index page

I have followed this to the letter and when i get to hit down on the bootloader and switch on my 9600 the little window just hangs there? i have tried lots of different combinations and two laptops one running vista and the other xp to no avail.any advice appreciated.
at the moment my receiver is running BT:1.34 SW:3pehr K:72

[simosgr11]

this steel working with protek 9600 ip ??

[Billyboy312]

I have just been given a Protek 9600IP box which I don't know too much about.

The software on the box reports as BT:1.34 SW:v1.10.

Would it be worthwhile trying to update the software to t53 bin file as in post 6 above?

Thanks in advance.

[cactikid]

if you want box to work,usually box stops working on old firmware.

[vaiosbratsos]

hi, where i found an - id - for my maxx1000 to unlock the lock channels

[mdt]

hi, where i found an - id - for my maxx1000 to unlock the lock channels

ive pm,d the guy again for you and if there still available you will have to send the money to my paypal account like last time,regards mdt

[vaiosbratsos]

ive pm,d the guy again for you and if there still available you will have to send the money to my paypal account like last time,regards mdt

hi, i sent the money to your paypal and send me the id.

[seamouse]

simple as above, find a good server