openbox s11hd c-line

[rhinoranger]

hello, just bought an openbox s11hd, could anyone please tell me what firmware/software i flash it with so i can enter a c-line or point me in the right direction , i have looked for a tutorial on the forum but no joy, any help would be greatly appreciated

[DeejayAJ]

Your current firmware could be fine, just scan the satellite & enter your cline.

For a better channel list try;

http://www.digital-kaos.co.uk/forums/f184/ocd-sky-uk-channel-list-11-03-a-260273/

Newer firmware;

http://www.digital-kaos.co.uk/forums/f184/latest-openbox-firmware-205077/

Unzip, put on a usb stick & "Upgrade by USB".

[lagerland]

Have a read of shadys guide m8 that will put you right................

https://skydrive.live.com/?cid=18c3b1693bc85898&resid=18C3B1693BC85898!124&id=18C3B1693BC85898!124

[bodserbrown]

I read shadys guide and still failed! the box says it cant find Cccam.cfg when it tries to update. Does the file need to saved as special?
Does it need to contain anymore than the c line? any help would be appreciated

[lagerland]

I read shadys guide and still failed! the box says it cant find Cccam.cfg when it tries to update. Does the file need to saved as special?
Does it need to contain anymore than the c line? any help would be appreciated

How to enter a CLine in Openbox s10,s11

Its easy to enter the CLine once you have the box.

You press the Menu button, go down to Network Local Setting, go across to CCcam plug setting, go to Manage Config Files, In manage Config files, choose CCcam.cfg, Click on Add (Blue Button) Now this is where it gets hard.

Protocol leave at CCcam
Host = IP Address
Port = Port Number
User = Username
Password = Password.

So if your cline looked like this

C: 192.168.1.3 16000 Billy Bigplums
Then in Host you would enter 192.168.1.3
Then in Port you would enter 16000
Then in User you would enter Billy
Then in Pasword you would enter Bigplums
Once done, press the yellow button.
You will now see the cline saying C: 192.168.1.3 Billy 16000 Offline.

Now press the Green button and it will put a tick next to Offline, exit the menu and it will say saving, Restart the box and it will work.

If you are going to use the USB to dump the Cccam.cfg file, make a notepad file and enter on the top line
C: 192.168.1.3 16000 Billy Bigplums

Save it as a cfg file and load it in using the menu.

[bodserbrown]

Thanks for the reply, been called into work, so will let you know how i get on later.

[lagerland]

Thanks for the reply, been called into work, so will let you know how i get on later.

No need to say thanx thats what the thanx buttons 4 good luck.................

[bodserbrown]

Hi guys am i doing something really stupid here??
i have my c line and i have cut and pasted it to notepad and saved it as Cccam.cfg
i have followed shadys guide and updated to the latest firmware - all ok
i go to update by usb, select CCcam Client Setup add my tick and press read(yellow button) and it says Cccam.cfg not found
i have tried it with two different usb sticks, two different c lines and it will not find it!! it reads everything else on the sticks. Assistance would be appreciated.

[darcu5]

did you format the usb to fat32.. make sure file saves as cccam.cfg and not cccamcfg.txt or cccamcfg.cfg, you could try installing cline with the remote manually, go to cccam on box, manage cccam -- add (green or blue button)-- top line cccam, host port username and pass, save it all then place a tick on it and reboot the box

[bodserbrown]

i did it again manually and it works, must have been a syntax error

[proton]

still cant get my box working

hopefully this will help get my box working