Mgcamd?

[harry1986]

i want mgcamd to work instead of the cccam i have installed everything but when i run it on the programme it doesnt let me view it and says cannot parse this emu i dont understand what im doing wrong?

[Simba92]

Should be as simple as

1. Downloading Mgcamd and the magcamd config file
2. Inputting your line in the correct format. (remember you must change the C: or N: to CWS =

3. And then changing your softcam to mgcamd.

[harry1986]

where do you put the mgcamd file and then the mgcamd config file and in the mgcamd file i put my line but what do i put in the mgcamd config file?

Should be as simple as

1. Downloading Mgcamd and the magcamd config file
2. Inputting your line in the correct format. (remember you must change the C: or N: to CWS =

3. And then changing your softcam to mgcamd.

[owengrey]

where do you put the mgcamd file and then the mgcamd config file and in the mgcamd file i put my line but what do i put in the mgcamd config file?

If i remember rightly the CWS line goes in the newcamd.list and you must have this file to, if not just make one using notepad and save it where the mg_config is.
works fine on my 800se.

[thomsork]

Hi, this is taken from another forum, so cannot accept credit for it.

This is some information about how to add N lines to mgcamd

Make sure you have mgcamnd installed like 1.35 or 1.35a

Your n line issued will start with an N: use something like notepad and remove the n and replace with CWS = instead

Example:~

N: myfriend.dyndns.com 15000 myname mypass 01 02 03 04 05 06 07 08 09 10 11 12 13 14

Convert to

CWS = myfriend.dyndns.com 15000 myname mypass 01 02 03 04 05 06 07 08 09 10 11 12 13 14

(you can edit this in notepad)

using a FTP tool add it to the end of the newcamd.list found in the Keys Folder.

In Linux they will be in /var/keys/newcamd.list or /usr/keys/newcamd.list or something similar.

Now press save and exit

Reboot the receiver then start mgcamnd emu and enjoy

Point to note:
You change from N: to CWS =. Taking note theres a space between the CWS & =

[gaza2001]

hi, is it okay to use the new version of mgcamd 1.38 or better to use mgcamd 1.35/1.35a?

[thomsork]

I use 1.35a, haven't upgraded to 1.38 yet

[delboy13]

i want mgcamd to work instead of the cccam i have installed everything but when i run it on the programme it doesnt let me view it and says cannot parse this emu i dont understand what im doing wrong?

what image are you using

[harry1986]

its all sorted now has installed in wrong location works fine now

[canford]

Where did you end up installing, lets other users know if they have same problems,thanks.

[shumifan50]

Below file names apply to OpenPli images.
if server is newcs then file is /usr/keys/newcamd.list with "CWS" line similar to N line
if server is CCcam then file is cccamd.list with line "C:" line as in CCcam.cfg

Note that the .list files names and content are case sensitive.

The message "cannot parse this emu" means there is a syntax error in one of the .list files. Rename them to something different and test one at a time. Fix the file that causes the error to be displayed.

Edit /usr/keys/mg_cfg file and at lest make sure the boxtype is correct (at bottom of file).

[downtime8]

MGCAMD

hi can u help me please to install mgcamd on vu ultimo ,i have mgcamd installed but have no idea where to get the mgconfig file and where to put it .when i start mgcamd.1.35a message no config file found setup mgcamd first in var/keys
i cant find this at all . thanks