VAR/ECT problem

[BlueBox]

Need some help i made a c-line in notepad and saved it as ccam.cfg then when i go in dcc ftp/var/ect and try and transfer file to left window it does not appear there so what am i doing wrong? file saved as CCcam.cfg.txt

Thanks

[daithi]

try copy and paste
also this talk isnt allowed on here you should no that
your about long enough

[benny/9]

Need some help i made a c-line in notepad and saved it as ccam.cfg then when i go in dcc ftp/var/ect and try and transfer file to left window it does not appear there so what am i doing wrong? file saved as CCcam.cfg.txt

Thanks

**********************************************
you beat me to it mate about no discussion
i have sent the poster a pm with info

[BlueBox]

Sorry guys been try to sort this problem out for hrs and not getting it

[RuberDuck]

also for the record in E2 systems it's ETC/ not VAR/ETC. thats for E1 boxes.

and it should not have the .txt bit at then end, when you save the file save it as exactly CCcam.cfg then select all files as the type to save as.

[BlueBox]

also for the record in E2 systems it's ETC/ not VAR/ETC. thats for E1 boxes.

and it should not have the .txt bit at then end, when you save the file save it as exactly CCcam.cfg then select all files as the type to save as.

i done what you have said but still the file not appearing on the left window

[canford]

I had same problem make sure your cccam software is shown in the softcam manager on your box first before you go any further, i have found that some versions of cccam dont install properly and therefor you cannot find cccam config file in dcc, just make sure you can see it in the box first, then run dcc and it will be there in etc.

[BlueBox]

I had same problem make sure your cccam software is shown in the softcam manager on your box first before you go any further, i have found that some versions of cccam dont install properly and therefor you cannot find cccam config file in dcc, just make sure you can see it in the box first, then run dcc and it will be there in etc.

Sorry but how do i go about checking that on my box Thanks

[canford]

If there is not a shortcut button by pressing blue button on remote, press menu/then setup/then softcam/ci and that will take you to the softcam manager,then were it says select softcam use your remote right button and it will show if anything is installed,if you find cccam press green,then do a full restart of your box.If there is nothing installed then you are going to have to download another version of cccam and install it,just make sure you uninstall the old version first and then install new version,it might takes a few goes before it shows up.

[andy91]

Just install a different cccam if its not there and start again.

Andy.

[BlueBox]

Just install a different cccam if its not there and start again.

Andy.

i going to play around with winscp see how i get on anyone else using this

[cokesux]

DCC is notorious for flaky operation. Just use a "real" FTP client like fireftp (firefox plugin), cuteftp, wsftp, etc... Hell, even Windoze Explorer works for the masochistic / mentaly challenged... I guess winscp should work if it also serves as FTP client, besides SecureCoPy...

--

[mdt]

DCC is notorious for flaky operation.

--

ive never had any trouble with DCC in E1 or E2 stb,s.... maybe ive been lucky? regards mdt

[RuberDuck]

i have to agree with cokesux i use a dedicated FTP client ( paid for version of flash fxp ) on all my receivers both E1 and E2 and it works flawlessly and always has.

[BlueBox]

Just install a different cccam if its not there and start again.

Andy.

i have done that now. problem is when i transfer the file to left window and goes over ok. and then check the line it show up as blank i tried DCC Firezilla also i connected the router belkin direct into my box when i open the file by right clicking edit shows up as blank no info in that left file