DM800HD Power Supply

[stigmata1823]

my dm800hd power supply is knackered but i have a spare power supply here and dont know if its ok to use? its output is DC19v 3.42A any help would be great

[benny/9]

my dm800hd power supply is knackered but i have a spare power supply here and dont know if its ok to use? its output is DC19v 3.42A any help would be great

************************************
they are very cheap on the bay mate and satfools
have them for about a tenner i would be a bit dubious
about using one that says 19v the psu unit for a dreambox is 12v
i did use one for a long time that came with a old
thomson speed touch router and it had the same
fitting that dreambox uses. but the router was rated at 12v

[stigmata1823]

************************************
they are very cheap on the bay mate and satfools
have them for about a tenner i would be a bit dubious
about using one that says 19v the psu unit for a dreambox is 12v
i did use one for a long time that came with a old
thomson speed touch router and it had the same
fitting that dreambox uses. but the router was rated at 12v

so just any 12v power supply that will fit the dm800hd will do then buddy?

[ramjet]

so just any 12v power supply that will fit the dm800hd will do then buddy?

yes m8

you can use the 12v dc from any pc psu to do this , and you will find them on auction sites to sort this out too

12v power packs are fine , ensure its 12v centre pin is positive and rated at at least 3.0 amp, or maybe get up to 4.0 amp

do not use anything over 12v like those laptop psu`s you asked about

also bear in mind the dc plugs can be different sizes too

probably best to get the ones used to power 12 volt monitors looking at what is available there

[stigmata1823]

yes m8

you can use the 12v dc from any pc psu to do this , and you will find them on auction sites to sort this out too

12v power packs are fine , ensure its 12v centre pin is positive and rated at at least 3.0 amp, or maybe get up to 4.0 amp

do not use anything over 12v like those laptop psu`s you asked about

also bear in mind the dc plugs can be different sizes too

probably best to get the ones used to power 12 volt monitors looking at what is available there

which one on ebay would do buddy there are quite a few on there cheers

[chic.]

psu

this should do it Power Supply PSU for Dreambox DM500S 500S, DM600, DM800 | eBay

[stigmata1823]

this should do it Power Supply PSU for Dreambox DM500S 500S, DM600, DM800 | eBay

should it not be higher than 1.5a should it not be 3 or 4??

[benny/9]

should it not be higher than 1.5a should it not be 3 or 4??

*************************************
the psu for the dm800 from where i buy
has this with there Power Supply listing
Power Supply for DM800/500HD (12V/3A). ?10.99
but the one in your link says it's for the dm800
and it should work ok.

if your anywhere near cheshire i will give you one
from my router that will work on a dreambox

[ramjet]

alternatively, I would buy the 12v 4A ones for monitors

2.5mm inside dia , 5.5mm outside dia , centre pin positive

[stigmata1823]

yes m8

you can use the 12v dc from any pc psu to do this , and you will find them on auction sites to sort this out too

12v power packs are fine , ensure its 12v centre pin is positive and rated at at least 3.0 amp, or maybe get up to 4.0 amp

do not use anything over 12v like those laptop psu`s you asked about

also bear in mind the dc plugs can be different sizes too

probably best to get the ones used to power 12 volt monitors looking at what is available there

I'm in Scotland buddy but cheers for the offer, I'll have a scout about the house as I have a few routers laying around and keep Yous posted

[stigmata1823]

cheers for th info guys got a router power pack and its powering up just need to try sort this damn no ca error that iv been at all night grrrrr

[benny/9]

cheers for th info guys got a router power pack and its powering up just need to try sort this damn no ca error that iv been at all night grrrrr

***************************************
if it's a clone box you need the forhike and natas
patched dreamup panel and use the last known ip
for your box. and upload and clear the problem then
load a new image with this loader panel and a null modem cable

[chic.]

where in scotland are you if you are in glasgow i can fix the no ca for you

[stigmata1823]

where in scotland are you if you are in glasgow i can fix the no ca for you

got it sorted buddy for some reason it would only take bootloader 69 so had to hunt for a #69 image and seems to be working ok now. im in stranraer buddy but if i need anymore help ill fire you a pm thanks for that

[andy91]

Bought one of these recently off Ebay for ?7.50 delivered.

http://www.ebay.co.uk/itm/1709045099...84.m1497.l2649

Andy.