Zgemma single tuner - good to use on a motorised system

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • digicon
    V.I.P. Member
    • Jul 2009
    • 8261

    #16
    If you loaded Catseye channel list via Dreambox edit and then decided to download Vhannbals plugin and update via the plugin then yes Vhannibals list would overwrite Catseye, with Vhannibal Plugin it really is made for the lazy person Press green button for plugins choose Vhannibal updater and then choose the channel list you want to download to the box everything takes about 20 seconds and your done, Faster than getting to a laptop loading DBedit then firing over a channel list.

    if you set Vhannibals plugin to Autoupdate it updates without you lifting a finger

    Comment

    • charlie567
      Member
      • Mar 2013
      • 50

      #17
      I have got dreambox edit downloaded and the catseye motorised list

      however you have mentioned the Vhannibals plugin here



      sorry to ask but how do you install this plugin ?

      is there a download section in one of the openvix menus and from this l can select this plugin or simply Download the plugin from your link then install in which folder ?

      thanks again for your patience

      Comment

      • digicon
        V.I.P. Member
        • Jul 2009
        • 8261

        #18
        you can download the Plugin directly from the Plugin feeds, or install the .ipk from the link and let it upgrade from V 1.1 to 1.4.

        I dont use OpenVix sorry so i assume the Vhannibals plugin is in there feed
        Last edited by digicon; 13 April, 2017, 18:26.

        Comment

        • charlie567
          Member
          • Mar 2013
          • 50

          #19
          thanks again.
          I have got the box, loaded the channel table but struggling to get any signal on any channels
          I left the old box on 0.8 west
          powered the edision, set the long and lat for birmingham
          but when l look for 0.8 west - its slightly out

          when l go to positioner setup and move it so l get signal, everytime l come out of the menu, it moves the dish again, so l cant find any signal
          I cant save the setting once l come out of the menu...which is frustrating. I cant seem to save the position of the satellite when the menu is exited


          If l try and switch off USALS, the dish does not move in Disqec 1.2 setting

          the satellite signal is displayed in the top corner - assuming it means the dish is moving. Really struggling at the moment to get any signal on any channels....

          any help would be appreciated to get the usals working please or Disqec

          update.....just seen the green store button after moving dish...gutted...
          will try 13 and see if l can tune that in and then 16, 19 and 28.2

          Looking a bit better now, stored 28.2 east and 13 east :-)
          Last edited by charlie567; 13 April, 2017, 17:17. Reason: maanged to store channels

          Comment

          • digicon
            V.I.P. Member
            • Jul 2009
            • 8261

            #20
            If using Diseqc 1.2 you have to use the Advanced option in the Tuner Configuration setting and then number differently every satellite you want to store so say 13,19,23,28 etc..

            Then goto the sat finder and move dish in small increments either east or west until you find the best signal for that particular satellite once done make sure the Number of the satellite corresponds with your saved number job done

            Comment

            • charlie567
              Member
              • Mar 2013
              • 50

              #21
              Nearly all sorted mate, thank you so much for your help
              Couldnt have done this without your help!!

              I will look at the bluetooth another time, main thing is to get the satellite positions stored and Sea Lion sorted out.
              Didnt know that you had to download the plugin for Emulators....learning all the time here :-)
              Last edited by digicon; 13 April, 2017, 20:15. Reason: Edited for Forum Rules

              Comment

              Working...