ca error on my clone 800hd

[steve29662]

messed up my dreambox 800hd what i got for Christmas, tried to put some boquets on it and sent my old dreambox 500 settings too, then it started to hang on boot and showed the splash screen then the screen on the front of the box went off, with just a red light flashing, so i thought I would put a new image on it NabiloBlackHole_DM800_012 via webpage and now get ca error message, so i connected to dreamup via a cable and it show up my box, box type dm800, but then a error comes up " is not valid integer value" can anyone help, can't connect via ethernet anymore !!!

please help regards Steve

[kaitum]

Assuming you used a Patched img file for the clone!
Try this.

http://www.digital-kaos.co.uk/forums/f34/fix-no-ca-error-70341/

[dctyper]

too long, just flash the bl you need, you will find in dl section

[steve29662]

thanks Guys,

I tried that it did'nt work got error file to big, but I got it working from a member on another site, big tahnks to Sabasa, he wrote this
"hi
what you have to do
1-run dreamup , connect DM800 with cable
(I useed my null cable steve29662)

2- under dreamop select network and in the remote ip (box) put the ip you want for your box
( try any ip if you haven't got your dreambox one steve29662)

3-now switch on the dreambox, dreamup will prepared the box for flash
when ready for flash
( I used enforcer to get the greyed out box to work steve29662)

4 take the remote ip (box) then follow the procedure through the web now
192,168.xxxx.xxx
will get to the upgrade firmware page
( this part 4, I didn't need to do as I got the pop up box to add bootloader 72 nfi file and then it flashed, rebooted and it loaded nablosat image which I had put onto the box earlier that caused the box not to boot.
This will force the box on bootloader mode"

all I did was to add my ip address of my box into "REMOTE" box in Dreamup with network box checked, still using enforecer and null cable still connected was able to send a new bootloader 72 to my box, repowered my box and it started to boot.

hope this will help others.

regards Steve

[kaitum]

Nice. I tested it but it did not work for me. My sim was broken most likely by a power spike. But if you just deleted the information on it so I think they works fine with the enforcer. Although bootloader 72 was too big. I tested only through dreamup. Next time (if it happens again) I'll try connecting dreamup and then flash through the web as you did.
Thank you Steve

[georgiosm]

Hi people.
I am facing a similar problem with no ca error .

There are two diferences at my problem
There is no pop-up at Dreamup saying that i have a ca problem and the other problem
is that when i do enforcer the dream up says "waiting for OK from box to beginn upload..." and never starts to upload.

I tryed to unplug - replug and gives me a blank "Wrong Response" with no http error on it..

Any ideas ?
How many time shall i leave dream up to wait ok from the box ?

Thank in advance
P.s. This is the log of the dream up
12:37:32 πμ box type: DM800
12:37:32 πμ Enabled recovery of bad sectors
12:37:54 πμ Calculating checksum...
waiting for OK from box to beginn upload...

and stays there for... ever ?? (at least i tried it 30 mins)

[steve29662]

hi,
I to did have a pop up when the dreambox was first connected, but closed the box and all dreamup showed was the name of my box "dm800" that it nothing else.

did you keep the silver on/off press in when you plug the power cable back into the box ?

it shows DREAM in big letters, then connect the null cable.

also try other older copies of dreamup, the latest copy 1.3.3.4 didnt work for me I used 1.3.3.2



hope that helps

[georgiosm]

Belowe i attach the response of dreambox when i power on with telnet connected to serial port at 115200

(c) 2007,2008 Dream Multimedia GmbH. All rights reserved.
Dreambox DM800
FIRST STAGE 1.00 {BO23456}

2ND STAGE OK, build #75 (20091005)

0.000 - BCM board setup
{00000126,00000126,00000125,00000124,00000123,0000 0133}
0.007 - fp init
0.008 - ca init
CA invalid
OLED found!
NO CONFIGURATION DATA PRESENT. STOP.
* ERR01: NO CA FOUND

apparently my sim card is off right ?

[sotiris_n]

The same problem!

Hi,

I have the same problem no ca found!
I try to flash an image with dream up second stage and on the beginning it seas uploading flash-loader, then it comes up uploading completed, waiting for acknowledge!
I use the enforcer and when i try to flash it seas
calculating checksum...
waiting for ok from box to begin upload...
and stack

Does anyone can suggest a solution for it?

Can anybody help please!

Many Thanks

[southpaw]

Hi,

I have the same problem no ca found!
I try to flash an image with dream up second stage and on the beginning it seas uploading flash-loader, then it comes up uploading completed, waiting for acknowledge!
I use the enforcer and when i try to flash it seas
calculating checksum...
waiting for ok from box to begin upload...
and stack

Does anyone can suggest a solution for it?

Can anybody help please!

Many Thanks

i too got to this stage , take ip number from display ,(box display should say http mode then ip number) , and flash through web-browser , worked a charm for me

[georgiosm]

Hi,

I have the same problem no ca found!
I try to flash an image with dream up second stage and on the beginning it seas uploading flash-loader, then it comes up uploading completed, waiting for acknowledge!
I use the enforcer and when i try to flash it seas
calculating checksum...
waiting for ok from box to begin upload...
and stack

Does anyone can suggest a solution for it?

Can anybody help please!

Many Thanks

I have exactly the same problem, no ip from the networks dhcp no nothing.
My bricked 800 stands on the self ..
Still waiting for someone to have a bright idea .

[halau]

try this it worked for me and some others

http://www.digital-kaos.co.uk/forums/f34/no-ca-found-file-big-fix-73198/

[flori]

Hi,

i can?t connect with DreamUp. There is a error message: "is not a valid integer value"