Clone Duo Open pli (kernal 3.0)Oscam-cccam sky uk Cooltv

[Data7]

oscam.user =flines ie you give
oscam.server =clines ie you take
look at the file i gave a link to.

oscam.user

[account]
user = mym8
pwd = XXX~~~~13e
description = any description you want
group = 1
uniq = 1
cccignorereshare = 0

send me your msn and i will see if i can help you better.

[madmanuk]

so i won't need to use cccam when iv done that and when i have done that should it work mate,Im not on man mate but you can have my email if you want.
thanks pal

[Data7]

it is far quicker to be on msn and get it sorted real time rather than wait for you to find open read anawer the email

[madmanuk]

i will try and get msn mate

[Data7]

no problem m8

[Data7]

This is taken from another forum.

Here are the contents of my four files:

This for Sky UK card in upper card slot with Oscam5953/CCcam213. This is running under Blackhole 1.6.5 but I don't imagine Vix it too much different.

There are 4 files:

CCcam.cfg in /etc
oscam.conf, oscam.server & oscam.user all located in /etc/tuxbox/config

CCcam.cfg (if you are already running CCcam, back up your working settings BEFORE you install the new cam).

BOXKEY: /dev/sci0 XX XX XX XX
SMARTCARD CLOCK FREQUENCY: /dev/sci0 3570000

N: 127.0.0.1 12000 test1 test2 01 02 03 04 05 06 07 08 09 10 11 12 13 14 256

(I left my boxkey in initially so that this file would work with both CCcam alone or OscamCCcam but you can remove that line later if you want, once you get it all working)

oscam.conf

nice = -1
WaitForCards = 1
logfile = stdout
preferlocalcards = 1
saveinithistory = 1
[webif]
httpport = 8888
httpuser = admin
httppwd = admin
httpallowed = 192.168.0.100-192.168.255.255
# protocols
[newcamd]
key = 0102030405060708091011121314
port = 12000@0963:000000;12001@0963:000000

(the line httpallowed includes all private network IP adresses or you can just replace this with the ip address of your box. This will allow you to look at the web interface via your browser so if the ip address of your box is 192.168.2.10 then in your web browser you would type 192.168.2.10:8888 (8888 is the port number that it is using). The username and password are both "admin".

oscam.server

[reader]
label = slot1
protocol = internal
device = /dev/sci0
boxid = 00000000
blockemm-u = 0
blockemm-s = 0
blockemm-g = 1
blockemm-unknown = 1
emmcache = 1,3,2
group = 1
caid = 0963

(Whilst this config does not require a boxkey, I found that it will not work if you completely remove this line. I just put 8 x "0" here and it works for me).

oscam.user

[account]
user = test1
pwd = test2
monlevel = 0
uniq = 0
group = 1,2
au = 1
caid = 0963

Make these 4 files, and place them in the folders I have mentioned, either with explorer or with FTP. When you have copied the files there, double check that the permissions are correct. With Filezilla, right click the files, and make sure the numeric value is set as 755 Double check the permissions for /etc/tuxbox/config are the same also. If you use Windows Explorer, right click each file (and the Config Folder) and make sure the read/write permissions are the same. Then go in and make sure that oscam/cccam is set as your default cam.

Switch your box off, and then back on again and let it start up. I shut my box down on one of my subscription channels and thought it wasn't working because the picture didn't clear instatly, but it took a couple of minutes to sort itself out and clear the my subscription channels. This delay is only for the first time you start the box. Further shutdowns and restarts clear subscription channels almost instantly.

If it clears OK then you can view your entitlements via the web interface.

Hope this is of some use.

[madmanuk]

ill try that pal thanks

[madmanuk]

hi mate i have done all this and its saying in oscam.ms) (of 0 avail 0) (no card support 0963:000000)
.
Its clearing channels but not sport.
thanks

[mdt]

hi mate i have done all this and its saying in oscam.ms) (of 0 avail 0) (no card support 0963:000000)
.
Its clearing channels but not sport.
thanks

try oscam 6059... is it saying card or network when it clears a channel? regards mdt

[madmanuk]

in oscam its saying no card support mate

[madmanuk]

ok i have got it running now with the files of a 500 that was running oscam/cccam and it seems ok,Its setup in my living room but when its gets moved to a new location on my network oscam won't work and i don't know why, its only been moved 30 feet away,?.Running Oscam5953/CCcam213
ps
where do i look for the ECM times.
thanks lads

[brasco03]

Will this also work with a genuine VU+ SOLO 2?

[madmanuk]

try it mate

[brasco03]

I am new to all this so my question is if I input all the text you wrote into telnet will it do whats needed for all sly channels to unlock as thats what I am after its just for testing out what the box can do though and I have a vu+ solo 2

[brasco03]

Anyway I tried this image and for some reason all the FTA channels dont work well on my genuine box but all the extras in this image make it super so I wish it worked on my unit