CIM clone Opel Astra H PIN code

[daten]

Hi
could someone help me for the Opel Astra H CIM module PIN
Valeo 2810502
GM 93184321
Manufacturing date 22.03.2017
Attached original eeprom reading 95160
Could you confirm if to replace it is enough to copy the 95160 eeprom, the references are exactly the same, attached MCU CIM image.


Thanks

[Bllinda]

No pin code, damp. what is needed .... ?

Hi
could someone help me for the Opel Astra H CIM module PIN
Valeo 2810502
GM 93184321
Manufacturing date 03.30.2009
Attached original eeprom reading 95160
Could you confirm if to replace it is enough to copy the 95160 eeprom, the references are exactly the same, attached MCU CIM image.


Thanks

[daten]

No pin code, damp. what is needed .... ?

I want to clone the sim, but first I want to check the pin code, vin data.

[Ninjor s]

dump bad readed,unsolder eeprom chip and read again.

[daten]

dump bad readed,unsolder eeprom chip and read again.

The 95160 eeprom reading is done with the desoldered vvdi prog eeprom programmer.
Check the eeprom read 95160 from the other CIM unit and they are similar

[budata]

I also think it's a bad read….try again or replace the device...

[daten]

I don't have the vehicle in my workshop but I managed to communicate with the new cloned CIM with the original data from eeprom 95160 and everything seems to be fine the vin is correct, there is a programmed key, I managed to calibrate the steering angle sensor using the pin that I I provide the owner of the vehicle.
But I have a fault code
B3057-00- Security code not programmed

[Ninjor s]

reset and program again.

[daten]

reset and program again.

You mean reprogram the pin code?

[Bllinda]

Read any of these blocks

https:/ /sutarta.lt/skelbimai/automobilio-pasas-car-pass-6625443.html

[Ninjor s]

You mean reprogram the pin code?

.......yes here virgin cim CIM Opel H_EEPROM 95160 Virgin.rar

[Bllinda]

.......yes here virgin cim CIM Opel H_EEPROM 95160 Virgin.rar

What do you think about that ....

I don't have the vehicle in my workshop but I managed to communicate with the new cloned CIM with the original data from eeprom 95160 and everything seems to be fine the vin is correct, there is a programmed key, I managed to calibrate the steering angle sensor using the pin that I I provide the owner of the vehicle.
But I have a fault code
B3057-00- Security code not programmed

[daten]

Hello
Thanks to all for the help
I want to confirm that the cloning has been successful, the engine starts without problem. I don't understand why no calculator can calculate the pin code. I also thought that the reading is bad or the eeprom file is corrupted.
I hope one day to discover the mystery.

[Bllinda]

Hello
Thanks to all for the help
I want to confirm that the cloning has been successful, the engine starts without problem. I don't understand why no calculator can calculate the pin code. I also thought that the reading is bad or the eeprom file is corrupted.
I hope one day to discover the mystery.

Did the error go away by itself?

But I have a fault code
B3057-00- Security code not programmed

[kiszka]

I don't have the vehicle in my workshop but I managed to communicate with the new cloned CIM with the original data from eeprom 95160 and everything seems to be fine the vin is correct, there is a programmed key, I managed to calibrate the steering angle sensor using the pin that I I provide the owner of the vehicle.
But I have a fault code
B3057-00- Security code not programmed

wystarczy zaprogramować pin nic więcej