RENAULT CAN CLIP REPAIR SOLUTION

**racin-snake** · 20th May, 2011, 04:01 PM

try loading driver manually from the clip file search the forum for install information for clip the dll sometimes has to be input manually

from file in the program

**sc202** · 20th May, 2011, 07:47 PM

not only detects cypres an unknown device

**sc202** · 20th May, 2011, 07:48 PM

You can not manually load the driver

**racin-snake** · 20th May, 2011, 08:10 PM

oh well i did ...when setting up my clip ?
manually found cypress driver for installation and it then loaded from the file on desctop
but it might be different with your setup so ....good luck

**mishu_b** · 21st May, 2011, 02:25 PM

Originally Posted by bo0st

Hi all
Im late...sorry
here is link for CLIP v55 install...please reupload to rapidshare. dont kill my server

http://www.fastestracing.com/Clip V55.zip

Thanks ladies

I can not open the archive, I get this error message:
"cannot open file: it does not appear to be a valid archive"

I would appreciate the effort if someone will upload a good archive for us!

many thanks!

**racin-snake** · 22nd May, 2011, 05:36 PM

copy file from dvd to desktop or from the original and load when it plugs in to the car and asks for the cypress driver it will ask if you want to automatically want windows to load click no
you will find driver to install show the file in the desktop and it should load
also some more learned guys on the forum have produced step by step instructions to load if you use the search facility

HTH

**mishu_b** · 24th May, 2011, 11:42 AM

@ racin-snake = did you answer to my post? if yes - your post is not relevant to my question.

I have asked for v55 archive which I could not open up at that time.

Now the issue is solved.

But I still have the issue with 20% stop. Where should I look first?

should I change the AN device too?

thanks

**vanya86** · 24th May, 2011, 09:36 PM

Repair solutions and referent points for test.

If usefull, click thanks

**dave1977** · 11th June, 2011, 08:50 PM

Originally Posted by baner

but, if you want to hear my opinion, then I think that you have malfunction CLIP device, ISO part of it is not functioning properly, and need to be repaired. It doesnt matter if you have both green LEDs for ISO and CAN illuminated, that is not a prof of fully functional CLIP device.

Hi, I have clip clone and software v108. From what you have written it sounds like I have the same problem.

Installed fine with 4 drivers etc, but when connecting to the car, I enter the VIN manually (how do you make it read it automatically??). Select engine/chassis code etc then run a full computer test. There is clicking noise, dashboard display flashes on/off a couple of times, then I get a screen showing various computers. The UCH I can get at fine, but the ECU is unavailable. There is absolutely nothing wrong with the car. I bought the CLIP to diagnose a non-runner.

Other weird things: cannot read any live data - error message says "ISOxxxxx not supported" or somesuch thing. This is basic shit right? An ELM 327 should read it no problem.

Mileage reported is not consistent with the dashboard.

What do you all think? Is the CLIP broken? Anything else I could try?

Thanks for reading!

**ototest** · 11th June, 2011, 09:01 PM

Hello friends,
if need any help for repair Renault Can Clip, you can send PM to me. if you are not electronic technician , very difficult repair byself. Regards.

**mishu_b** · 12th June, 2011, 02:11 PM

Originally Posted by ototest

Hello friends,
if need any help for repair Renault Can Clip, you can send PM to me. if you are not electronic technician , very difficult repair byself. Regards.

why PM and not here - for everybody?

I have a issue with ISO part - 20% fw upgrading stoped after I solved the power supply with the LDO.

where should I look know?

atb

**dave1977** · 12th June, 2011, 02:18 PM

Further to my last message, the exact error displayed by CLIP is:
DIALOGUE NOT ESTABLISHED: CHECK
That the vehicle has OBD equipment
The connection to the vehicle
Protocols supported by the tool:
-ISO 9141-2
-ISO 14230-4

Car is Megane II (2008) 1.5dci

Any thoughts?

Cheers!

**vanya86** · 18th June, 2011, 12:55 AM

All china clones have problems with Connector (round one) on device (side to OBDii)

Connect +12V to pin 16, and GND to pin 4&5. Than check pin 7 do you have +12V (Kline) and most common problem is CAN, one pin don't have 2.55V

**z786** · 18th June, 2011, 11:05 AM

can you PLEASE show a picture/diagram on what to look at and how to fix

thanks

**vanya86** · 18th June, 2011, 12:42 PM

After you connect supply on obd, then connect USB, run soft.

Check voltage on pin 6 and 14, you need about 2.50V

If you have it, then check LED diodes if only 1 is turned ON, than you have problem with ic on 2. picture where is 4.88V shown