VAG-COM/VCDS EVERYTHING

**mishu_b** · 21st July, 2011, 05:45 PM

...
mattydr67 is right
check into about tab if the serial is full registered/ activated.

otherwise the tool will work for several iteration and than will stop to work.

atb

**makura** · 21st July, 2011, 06:57 PM

Originally Posted by mishu_b

not really - this is only the FTDI "dump" - if your tool has inside also one uC that you will need to reprogram too the uC.

atb

oops
The how do i program the uC?do you have the dump?i want to have all the facts before i make things worse and the solution even harder and longer.
thanks for the attention and help,like i always say you will find the greatest mindds on DK,BIG UP

**mishu_b** · 21st July, 2011, 09:34 PM

...
first - describe as deep as you can the issue.
put also few pictures here, and after you will receive the answer to your issue.

atb

**qwest123** · 22nd July, 2011, 04:46 AM

awsome
awsome
awsome
awsome

**dar10ck** · 22nd July, 2011, 06:51 AM

Greetings, I have re-read entirely, but and haven't understood one
At me vag106 clone based on ft232rl
If I reflash mega by 908, than what dump I need to reflash ft, whether am necessary reflash gal and whether there is a probability to start 10.6.4

sorry for my english (translate.ru)

Harrycz44 · 22nd July, 2011, 07:35 PM

Originally Posted by mattydr67

Take a look and tell me if it is full resgistred/activated.
just because the inetrface it was erased because this it hasn't this softwear in blacklist but it is not a serial for that language just for englesh.
I tested it for romanian laguage with 10.6.4 , it's working I mean the interface it wasn't erased but the softwear remain unregistred. It didn't become Full registered/Activated.
Good luck

yes full activated

**vilenjak** · 24th July, 2011, 10:50 PM

Does the VCDS interface can support another software, e.g. FiatEcuScan or ... ?

**mattydr67** · 25th July, 2011, 06:02 AM

Originally Posted by vilenjak

Does the VCDS interface can support another software, e.g. FiatEcuScan or ... ?

M8 it is a dedicated interface.
It dosen't work with other softwears.
For FiatEcuScan you need Vag kkl
Well VCDS has a function OBD II and can connect to OBD II cars and it works like ELM327 OBD II softwears
You can use it.
Good luck

**Qwarz** · 25th July, 2011, 08:39 AM

I have reflashed VCDS besed on FT232BL with good dump ( it is 908 EN arash) and FT as well.After that VCDS program says that firmware is uknown and needs to be updated.It is really strange because I know dump is fully working and interface should show firmware version etc.I'm wondering if GAL needs to be programmed as well. Has anyone had similiar case?

**mattydr67** · 25th July, 2011, 10:25 AM

Originally Posted by Qwarz

I have reflashed VCDS besed on FT232BL with good dump ( it is 908 EN arash) and FT as well.After that VCDS program says that firmware is uknown and needs to be updated.It is really strange because I know dump is fully working and interface should show firmware version etc.I'm wondering if GAL needs to be programmed as well. Has anyone had similiar case?

No m8 but 908 is older and it's asking you to upgrade it.
When you'll do this your tool will be erased again.
I don't know if that dumps are very good for you tool.
Why don't you use the dumps for 11.2 and 10.6.4?
And you'll have the latest softwear of VCDS.
Don't ask me where you can find it because this dumps are for free and you can do a goole serch and for sure you'll find item.
Good luck

**Qwarz** · 25th July, 2011, 12:09 PM

It doesn't matter what dump is used.Everytime VCDS tells that upgrade is needed but update cannot be performed because version is uknown.I changed also dates in PC but the same thing occur.
I suppose it might be problem with GAL which has "previuos" dump or atmega is damage.

**mattydr67** · 25th July, 2011, 02:01 PM

Show me a pics with this.
First you must flash FTDI the Atmega with 2 dumps.
One for flash and the other one for EEProm
Then you need the Original installer for the version of the VCDS
Good luck

**Qwarz** · 25th July, 2011, 02:27 PM

I used working dump (flash+eeprom) and suitable ept.
Except that original version of VCDS was used as well.
This what I observe is fact that LED changes colour when I plug USB kable into computer.

**mattydr67** · 25th July, 2011, 06:24 PM

Do this and plug it into the car as well
good luck

**aminebot** · 25th July, 2011, 09:21 PM

Originally Posted by Qwarz

I used working dump (flash+eeprom) and suitable ept.
Except that original version of VCDS was used as well.
This what I observe is fact that LED changes colour when I plug USB kable into computer.

try to connect interface to car first , wait 5 seconds , connect it to usb and wait another 5 seconds , and make a test.

if interface has protection chip , desolder it.

if it does not work reprogram Atmega , at end of programming you should get a message saying if Atmega was successfully programmed or not.

Thread: VAG-COM/VCDS EVERYTHING

Thread Tools

Display

vcds

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions