VVDI PROG

[testit34]

Hi
Did you have to lift legs or remove parts?
Thanks

[exSPEEDyTOR]

Hi. need cutting 2 wires. use the picture. if you have software. see manual, variant 4.2015-10-16 09-18-20 Скриншот эк&#108.jpg

[testit34]

Hi
I tried today on V2 Cas4. I was able to read D Flash and P flash but it wont let me reset Sec so I can program unit.
When you try to reset sec says Chip is Crypt FF Operation Failed. Any ideas ??

Thanks

[CryptoKey]

HI Samic.

CAS2 with 2K79X, there are two versions one can not read.
ID-2K79x not recognize possible that another pinout, R270 says "NOT 5v Power" with the same connection that standard version of the image.

- You could look and reprar this ruling.

CAS2 I have this test,
Error VVDI prog 2k79x BMW.jpg

[testit34]

Hi
The cas I tried to do is CAS4 5M48H with Silver Crystal. It wont unlock Sec byte to program CAS.
When you try to reset sec says Chip is Crypt FF Operation Failed. Any ideas ??
But you can Read D flash and P flash no problem and data is valid.
You just cant unlock to edit data and rewrite.
Thanks

[Samic]

HI Samic.
CAS2 with 2K79X, there are two versions one can not read.
ID-2K79x not recognize possible that another pinout, R270 says "NOT 5v Power" with the same connection that standard version of the image.
- You could look and reprar this ruling.
CAS2 I have this test,

Hello friend,the connection diagram of this type will add in next version.
this type of the connection diagram is only a little different about the "CLK",other connection lines are the same.
you can refer to this image,then try again.
CLK-Left.jpg

[Samic]

Hi
The cas I tried to do is CAS4 5M48H with Silver Crystal. It wont unlock Sec byte to program CAS.
When you try to reset sec says Chip is Crypt FF Operation Failed. Any ideas ??
But you can Read D flash and P flash no problem and data is valid.
You just cant unlock to edit data and rewrite.
Thanks

thank you feedback this issue,we will check and fix this problem.

[kohli]

is good tool but now ther's vvdi2 2000 D

[CryptoKey]

SAMIC, this pin, not works. for VVDI-Prog
cas2-V2 2K79X - siemens 59510.21.01C
does not identify the MCU, I get in the ID0000 software.

R270 also tells me (Not 5v Power).

[PremierD]

Probably something to do with the thermal lance you used to throw solder at it from 20 meters away mate

[Johnner]

.................

[CryptoKey]

Age takes its toll on the eyes, but is well tested.

---Nothing, not leaving it beautiful, this is not working.
-PremierD Now after it clean you should tell me what is the pinout,,

[clusters]

Age takes its toll on the eyes, but is well tested.

Then the facility that rebuilds clusters for GM must be full of geriatrics.

A sample of their "reflow" work in a rebuilt cluster that failed.

[Samic]

SAMIC, this pin, not works. for VVDI-Prog
cas2-V2 2K79X - siemens 59510.21.01C
does not identify the MCU, I get in the ID0000 software.

R270 also tells me (Not 5v Power).

please use the current latest V3.9.1 version.

[CryptoKey]

found in all the versions, always the same. NOT ID-0000
MCU - 9S12DG256 also beaten.

this does not work!!!, nor welding, nor versions, all checked ..here the technical VVDI-PROG he stayed asleep.