hi everyone, i have a eurovox blue and i tried to install the software onto it. when i tried to do it the the software was installed successfully but nothing comes on my t.v when i plug it in. please can somebody help me!!!
-
-
try reloading software again...then when you plug back into tv just wait a few mins i used the one dated 4/12 took about a min or two before i got picture -
clone
your box may be a clone. BEFORE YOU DO THIS FLASH WITH F/WARE FROM APRIL 08 .TO GET THE F/WARE D/LOAD BIGMAQ TOOLBAR AND CLICK ON FILES AND FIXES, YOU WANT THE BLUE BOX FLASH FROM 21/04/08.heres what u do take out the scart lead form ur eurovox and tv
connect a coxial cable from the back of ur eurovox to ur tv (a coxial cable is the one u use to connect ur vcr to ur tv )
ok now u have ur eurovox connected to the tv by coxial cable only have ur eurovox on and not in standby but on
now using ur tv remote scan the channels on ur tv do an automatic scan of channels on ur tv u should get to a screen asking for a code the code using ur eurovox remote now is either 0000 or master code 1004
now u will press menu>goto config>cleardata>clear channels>factory default ?choose correct symbol rate then power scan.once your box is back on flash it with the blue box clonesafe f/ware.
sigpic
its the stuff we think we know that stops us all from learningComment
-
Hi Camelv, I have a couple of eurovox max 2006 boxes, which I got for next to nothing of someone as they don't work? i have found these to be clone boxes - i opened one and it had red paint on the screws.
I've tried flashing with a clone image - it is a successful download - but I get 0000 on the display, the remote doesn't work, cannot even power on and off from the remote. However on the tv I do get an image through scart and video out (yellow phono) this says 'channel not currently available'. As I said the remote doesn't seem to do anything - change channel or menu etc.
do you still think I need to do the instructions as per RF cable - I'll probably give it a go tonight anyway...Comment
-
follow the guide above and you should be able to access the menu and get your box working again .
sigpic
its the stuff we think we know that stops us all from learningComment
-
camelv
Afternoon mate,
The April fix dated 21-04 isn't clone safe, if people with a clone flash there boxes with that firmware it could brick em.Comment
-
if it's bricked is there any way of fixing it??? i think someone may have put the old image you're talking about on it...
i have just connected box via coax and get the same screen - channel not currently availableComment
-
ok - i think i know what to do now - jtag kit off fleabay?Comment
-
Happy new year all!!
Well, my jtag kit arrived today and after a bit of messing around I got it to connect. For anyone stuck getting these errors in jkeys or skymax:
init jtag idcode : ffffffff
unknown device
error no response from jinterface
Check you parallel settings in bios are set to epp and 378 - I was checking the physical connections over and over and this was the problem!
Make sure the red side of the ribbon is closest to the power supply.
Hopefully that info will help someone?!
It didn't help me though! after running skymax s/w and erasing all then writing eurovox blue, I then put clonesafe image dated 16042008 from bigmaq onto the box - guess what same error - channel no currently available - cannot do anything from the remote????
I only tried this on one box (but I have 3), they have omega chips, not intel if that makes a difference - I don't know if I used the wright s/w or image during jtag process??
please help someone.....Comment
-
Last edited by camelv; 7 January, 2009, 03:17.
sigpic
its the stuff we think we know that stops us all from learningComment
-
any ideas on my problem camelv?Comment
-
sorry never had to j tag, but i know you can also get a step by step guide on u tube, hope you sort it m8
hope this is what u need ,let me know.Last edited by camelv; 7 January, 2009, 12:17.
sigpic
its the stuff we think we know that stops us all from learningComment
-
thanks for that link - it allows me to watch youtube videos at work!
I will have a look at the instruction vid - but I'm pretty sure I did it correct???Comment
-
Sorry for hijacking the thread.... Just wondering if you can use a parallel -> serial connector while jtaging and still connect the box to your PC? Haven't got a parallel cable handy ya see.
ThanksComment
-
start a new thread m8 you will get more response to this.
also check this link m8
sigpic
its the stuff we think we know that stops us all from learningComment
Comment