Eurovox ex 5000 pvr HELP ME PLEASE

[impoundeddog]

whats up m8, and what have you done so far?

[StonerStevo]

i have flashed my box searched all the channels an found them all an it gets stuck on updating codes, now av been told i had software from july 2008 so put the newest 1 from december on it, when i go to put the software on it, its just sayin waiting for reciever and not doing nothin i have made sure its in port 1 tryed pullin the power cord out an plugging it back in and its just not workin for me. i have a usb conection going into my pc then the other end goes to my box dont understand were i am goin wrong

[impoundeddog]

if you have the latest firmware on the box,(check by going to menu/config/system info. what date is on the software on the box?)
leave it on sly sports 1 and let it update, can take up to 15-20 mins first time so just leave it and dont change the channel untill the picture comes in.

[satsmo]

Threads have been merged to alleviate the confusion as the queries where asked and answered on your last thread.

What you need can be found in the red stickies above.

[StonerStevo]

Try this m8 to find which com your Eurovox is connected to either using null modem or usb to null,

Problems with your PC/Laptop not recognising your eurovox.

To see which port your USB adapter is connected to, connect your USB adapter and follow the following instructions:

1. Go to the Start Menu
2. Right click on "My Computer"
3. Select "Properties"
4. Click on the "Hardware" tab
5. Click on "Device Manager"
6. Click the + sign next to "Ports (COM & LPT)"
7. One of the listed ports should indicate which port your USB adapter is connected to (e.g. COM1, COM2, COM3, etc.)
8. Go back to your map software program that you use to transfer data and make sure it is looking at the correct port.
9. You should be able to transfer data once the correct port is selected

If you need drivers go here

USB to Serial Adapter driver downloads and documentation

Follow my advice to step 7. Locate your USB Adapter (port *)

Right click on that port and select properties. Then select port settings, then select advanced. At the bottom of that tab will be a drop down box with the port selected (port * in your case). Use the drop down to select another port (eg 1, 2 or 3). If the port you want to use is already allocated to something else, you can use the same procedure to reassign that port after you have finished.
Save the selections in the usual way. The USB converter will be permanently assigned to the port you selected.
Thanks to celtic71

yer its sendin it now mate thanks very much an celtic 71, hope i dnt have nemore problems now been 3 days still not goin ha

[gizmo.1484]

Glad to hear that m8. It should be plan sailing from now on. After you have flashed your box then have a read off this to scan for channels http://www.digital-kaos.co.uk/forums...settings-9789/
Good look.

[StonerStevo]

Glad to hear that m8. It should be plan sailing from now on. After you have flashed your box then have a read off this to scan for channels http://www.digital-kaos.co.uk/forums...settings-9789/
Good look.

gizmo thanks alot mate been very helpful and iv now managed to get it workin.

[badapple]

When you see the message waiting for a response from the receiver, switch the box OFF/ON at the mains and the it will continue the download.
Also before scanning the box do a factory reset.

[crozzer]

[QUOTE=gizmo.1484;163492]Try this m8 to find which com your Eurovox is connected to either using null modem or usb to null,

Problems with your PC/Laptop not recognising your eurovox.

To see which port your USB adapter is connected to, connect your USB adapter and follow the following instructions:

1. Go to the Start Menu
2. Right click on "My Computer"
3. Select "Properties"
4. Click on the "Hardware" tab
5. Click on "Device Manager"
6. Click the + sign next to "Ports (COM & LPT)"
7. One of the listed ports should indicate which port your USB adapter is connected to (e.g. COM1, COM2, COM3, etc.)
8. Go back to your map software program that you use to transfer data and make sure it is looking at the correct port.
9. You should be able to transfer data once the correct port is selected

If you need drivers go here

USB to Serial Adapter driver downloads and documentation

Follow my advice to step 7. Locate your USB Adapter (port *)

Right click on that port and select properties. Then select port settings, then select advanced. At the bottom of that tab will be a drop down box with the port selected (port * in your case). Use the drop down to select another port (eg 1, 2 or 3). If the port you want to use is already allocated to something else, you can use the same procedure to reassign that port after you have finished.
Save the selections in the usual way. The USB converter will be permanently assigned to the port you selected.
Thanks to celtic71[/QUO

[DaVinylJunkie]

Hi All,
I'm new here having just taken delivery of Eurovox EX5100 PVR. I'll be obliged if you can offer any basic info regarding flashing, set up etc. I'm running Vista 32-bit Home Premium on my laptop and also have an older PC running XP.

Any help on pointers, pitfalls to avoid and general information will be greatly appreciated.

Thanks in anticipatipion.

DaVinylJunkie

[badapple]

Hi All,
I'm new here having just taken delivery of Eurovox EX5100 PVR. I'll be obliged if you can offer any basic info regarding flashing, set up etc. I'm running Vista 32-bit Home Premium on my laptop and also have an older PC running XP.

Any help on pointers, pitfalls to avoid and general information will be greatly appreciated.

Thanks in anticipatipion.

DaVinylJunkie

Use this softwa*e for your box> Digital Kaos - Downloads - UFL_EX5100PVR_DarX_16-01-09
All the other info u require is in the threads above. so have a read and u will be ok m8.

[chic.]

try the 1/12/08 firmware thats what i have on my box do not use the nosort 1 it may kill your box