Openbox s10 and Mgcamd

[DW190]

MGcamd is built into S10.

Just copy and paste your cws line into Newcamd.list.

Make sure the network is set to DHCP and reboot you box and router.

[dilwsi]

i have 2 lines i test on the openbox s10

1 will work in both cccam and mgcamd
but the other only in cccam... any one know what the problem would be.

I have copy and pasted them and also tried to enter it manually with the remote. Still no luck

[insrobbo]

MGcamd in openbox

Can anyone post a Working Newcamd.list withXXX in the user ID and Passwork, Ignore.list Replace.list as I can not get my files from the dreambox to work, if I can copy in my own details Im sure it will work

[althom40]

this n line set up as cws would be like this

N: test.dm800.com 12000 user1008 password102 01 02 03 04 05 06 07 08 09 10 11 12 13 14

enter newcamd -
set up single account
host - test.dm800.com
port - 1200
user - user1800
pass - password
deskey - 0102030405060708091011121314

press yellow to ok it and it shud now show in newcamdlist as

cws = test.dm800.com 1200 user1800

================================================
I can get CCcam working in my OB-S10 but not NewCamD.

I followed your instructions and entered the newCamD list via the MG plug file. Entered the instructions as above but when I go to yellow ok, it jumps to user1800. No way can I save this file.

I enter the same details via the CCcam.cfg and can load this
N: file. Similiar files I have tried and made active do not come on line. Any more tips ?
regards

[althom40]

Yes there are a lot more unresolved problems with the OB and a lot more bad and conflicting info given out.

[konami001]

same openbox s10 problem here... mgcamd does not...

[DW190]

I have OB s10 which works fine on both CC and MG

[mept1]

It dont work if you dont read up... plenty info on this great forum

[althom40]

It dont work if you dont read up... plenty info on this great forum

Well I have done plenty reading up and still cannot get NewCamD to work.

The NewCamD is embedded in the S10. How would I find out what version of NewCamD is installed in my box? Users are working with version 5.25. How do I find out mine.?

Please dont tell us that "google is our friend"

[althom40]

I have OB s10 which works fine on both CC and MG

Tell us where you entered the NewCamD file. If possible give us a step by step example using made up data. Seems to me there are lots of people with the same problem and would really like to know what is amiss.

[darcu5]

This is what your n line should look like

N: test.dm800.com 12000 user1008 password 01 02 03 04 05 06 07 08 09 10 11 12 13 14

Now Select;

menu
MGCamd Plug Setup
Manage Config Files
Newcamd.List
Select Green (i think) to add

set up single account
host - test.dm800.com
port - 12000
user - user1008
pass - password
deskey - 0102030405060708091011121314


the n line set up as cws would be like this

cws = test.dm800.com 1200 user1008

You can check it by following the above instructions again

-------------------------------------------------------------

To set the n line up to run as CCcam simly open notebook on computer, copy and paste youe n line like this

N: test.dm800.com 12000 user1008 password 01 02 03 04 05 06 07 08 09 10 11 12 13 14

Select to save the file as CCcam.cfg

Stick it onto your usb dongle, plug dongle into box, select

Menu
Network
CCcam Client Setup
Update files by usb
Manage Config Files
Select the nline (to place a tick)
exit back to tv
Reboot.

[Digiray]

I'm having the same problem.

I'm running a S12 straight out of the bix it had CCCam, Newcamd and MGcamd. My server runs MGCamd and I uploaded the newcamd.list via USB that my server sent me (so I know the line is correct), checked it to make sure it was ok, turned off the decoder with the red button, turned it back on and nothing.

I've done it about 50 times since I got it yesterday and no luck whatsoever. I've tried putting the line in manually, I have the Keep alive line in also, also tried removing the keep aline line, DHCP is correctly set, etc.

When I turn the decoder on, it never says Cam loading or anything like that, should it??

I've tried original firmware and also OPENBOX_S10_111117 firmware. Still nothing.

Help please!!!

[althom40]

This is what your n line should look like

N: test.dm800.com 12000 user1008 password102 01 02 03 04 05 06 07 08 09 10 11 12 13 14

Now Select;

menu
MGCamd Plug Setup
Manage Config Files
Newcamd.List
Select Green (i think) to add

set up single account
host - test.dm800.com
port - 12000
user - user1008
pass - password
deskey - 0102030405060708091011121314


the n line set up as cws would be like this

cws = test.dm800.com 1200 user1008

You can check it by following the above instructions again

-------------------------------------------------------------

To set the n line up to run as CCcam simly open notebook on computer, copy and paste youe n line like this

N: test.dm800.com 12000 user1008 password102 01 02 03 04 05 06 07 08 09 10 11 12 13 14

Select to save the file as CCcam.cfg

Stick it onto your usb dongle, plug dongle into box, select

Menu
Network
CCcam Client Setup
Update files by usb
Manage Config Files
Select the nline (to place a tick)
exit back to tv
Reboot.

===============================================
Thankyou Darcu5.
I followed your entries and got into the CWS entry within the NewcamD list file. What happens now? How do I make that line active?
I then tried your entry exactly for a N line and put that into my CCcam cfg file. It looks like this:-----
N: server1 user1008 12000 no active.

Looks OK so I copied an active |N line into the CCcam.cfg file
and ticked the box to make it active but alas the line just stayed dormant and would not come on line.
regards

[DW190]

===============================================
Thankyou Darcu5.
I followed your entries and got into the CWS entry within the NewcamD list file. What happens now? How do I make that line active?
I then tried your entry exactly for a N line and put that into my CCcam cfg file. It looks like this:-----
N: server1 user1008 12000 no active.

Looks OK so I copied an active |N line into the CCcam.cfg file
and ticked the box to make it active but alas the line just stayed dormant and would not come on line.
regards

MGcamd should look like this and copied into the "Newcamd.List"

CWS = server.aa 20042 abcde tuvwxyz 01 02 03 04 05 06 07 08 09 10 11 12 13 14


CCcamd should be like this and copied into "CCcam.cfg"

N: server.aa 20042 abcde tuvwxyz 17 01 02 03 04 05 06 07 08 09 10 11 12 13 14


abcde being the user name and tuvwxyz being the password.

When entered place a tick to make CCcamd active, exit back and reeboot box and router.


MGcamd doesn't have to be ticked. Just reeboots.


If you are entering manually and have an n line. change the top box to Newcam.

[darcu5]

Looks OK so I copied an active |N line into the CCcam.cfg file
and ticked the box to make it active but alas the line just stayed dormant and would not come on line.
regards
----------------------------------------------------------

Did you do a reboot after you selected the nline??

Also as DW190 said above, there is nothing to select on the MGcamd, just reboot and it connects.

Seems like there's a few people having problems connecting s10 to an nline.. i can't understand why, what version of firmware are you running.. i have firmware from 15/09/11 running on both s9 and s10, before that i had july firmware on them, both have worked fine for me.