DELETE AND PROGRAMMING REMOTE MITSUBISHI ASX 2015

[vitimax]

You need 8a42, try again with this code

Thank you for advice. Will try tomorrow.

[vitimax]

You need 8a42, try again with this code

When I added new transponder I used Pin Code 8A62, but new remote didn't synchronized with the car. Only one the 1st remote still in the system.
New ones can't added. Why new transponder added with pin code 8A62 and new remote didn't ?

[totalkey]

This is separate remote and transponder, you need precoded transporder and manual program remote

Sent from my VOYAGER2_DG310 using Tapatalk

[vitimax]

This is separate remote and transponder, you need precoded transporder and manual program remote

I used original key 6370A159, that was already precoded. I program old and new keys into the car, but couldn't program remote.
I used FVDI tools and X100 Pro tool and both tools didn't add remote to the car. Only old remote still works.
Maybe these tools can't do this procedure ?

[totalkey]

I used original key 6370A159, that was already precoded. I program old and new keys into the car, but couldn't program remote.
I used FVDI tools and X100 Pro tool and both tools didn't add remote to the car. Only old remote still works.
Maybe these tools can't do this procedure ?

There is manually way to do it, search Google, or here

Sent from my VOYAGER2_DG310 using Tapatalk

[vitimax]

There is manually way to do it, search Google, or here

No way to do that manually. Only some special tool can do it.
If you can recommend me manual instruction, I'll be very thankful and grateful.

[totalkey]

Basically I do this years by obd, gscan or avdi, but you.can try connect to immo with scan tool or x100 than push on off hazard button 7 times than push remote button, take a look in Google because I can't answer all your questions

Sent from my VOYAGER2_DG310 using Tapatalk

[obdsystems]

Basically I do this years by obd, gscan or avdi, but you.can try connect to immo with scan tool or x100 than push on off hazard button 7 times than push remote button, take a look in Google because I can't answer all your questions

Sent from my VOYAGER2_DG310 using Tapatalk

Seemed to have trouble doing one today - tried avdi and manually. guess need better tools

[castin]

Mitsubishi Eclipse 2007 - obd2 pin 1 to ground and 4(?) times on/off hazard button, then push button on remote and ok. Search on google. Meybe work.

[Buzztek]

Zed Full works 1st time every time I have done this remote.

I did once on skp900, but it took half an hour, and only worked once I disconnected the device, then reconnected and tried again.

Definitely separate remote and chip.

It was the "hold lock and unlock for 3 flashes, then lock or unlock for 1 flash.

All done on KD. The one I did on skp900 came back 2 months later and stopped working, re did it on ZF and hasn't come back since.

And all remotes are deleted when you need to add 1


Sent from my SM-G935F using Tapatalk

[ibritstone]

Knowing Mitsu, its probably a manual procedure for remote. Proxy should be automatic when you program the key

[p1et]

Is there any other tool apart from avdi and zedfull which can program remote to ASX? I tried Smart Pro, Lonsdor, Key Tool Plus without luck.

Anyone actually tried manual procedure? Doubt it work for that model year but maybe?

[Manta1600]

Is there any other tool apart from avdi and zedfull which can program remote to ASX? I tried Smart Pro, Lonsdor, Key Tool Plus without luck.

Anyone actually tried manual procedure? Doubt it work for that model year but maybe?

Few days ago I programmed ASX 2015 with Autel

I'm pretty sure that AVDI also can program it and also the other tools that you have so maybe you have wrong key or faulty car

[amm]

Did lancer 2008ish with avdi, and 2 ASXs with autel.

Lancer and one ASX aftermarket keys, and one ASX with universal remote and both avdi and autel programmed the remotes.

[fuzz1]

Hi
Are the keys from the lancer cs not the same as the asx? I think they are both omron keys with the chip separate in the remote.