Vu+ Duo Clone - problem, keeps getting stuck on 'starting' also getting green screen

[digicon]

Hi mate just curious if you still have the internal Hard drive attached try unplugging it and also remove any other USB devices in the DUO just in case you have any still attached.

Then try flashing it again,but try another USB port on the machine different as in one you have not already tried and then report back.

Just to let you know V2.0 have already had the Kernel 3.1.1 flashed so no need for anything like that at the moment also if your trying to flash Blackhole use 1.7.5 and below same with Vix use 2.4.155 and below.

Good luck

[kaisar1]

Hi mate just curious if you still have the internal Hard drive attached try unplugging it and also remove any other USB devices in the DUO just in case you have any still attached.

Then try flashing it again,but try another USB port on the machine different as in one you have not already tried and then report back.

Just to let you know V2.0 have already had the Kernel 3.1.1 flashed so no need for anything like that at the moment also if your trying to flash Blackhole use 1.7.5 and below same with Vix use 2.4.155 and below.

Good luck

tried with and without harddrive connected. no effect.

luckly at the moment it 'reading usb', light blinking. currently running 10-15min so far

[kaisar1]

look at the images please

[digicon]

Hi Kaisar1,

Thats still not right with the 'Reading USB' especially for 10-15mins it should go to programming and then erasing flash and programming again after just a few minutes.

Have you got any other USB sticks that you could try.

Regards.

[kaisar1]

Hi Kaisar1,

Thats still not right with the 'Reading USB' especially for 10-15mins it should go to programming and then erasing flash and programming again after just a few minutes.

Have you got any other USB sticks that you could try.

Regards.

thats what i thought. i previously flashed vu solo, took about 2-3 minutes.

i got a kingston 16gb usb stick. i will try that now. ty


--------------------------update

same thing happening with my kingston 16gb usb. i aint got a clue what to do know. shall i install icc security update using rs232 cable? or install kernal.

i aint got a clue with this box, dm800hd simple, transfer nfi file.

[kaisar1]

receiver never flashed, however loaded up after 10+ attempts starting > vu duo+ > saw bh 1.7.5 image then went to black screen, nothing functioning.

what should i do, install kernal or install icc security update bootloader

[DOUGALMCD]

Hi mate just curious if you still have the internal Hard drive attached try unplugging it and also remove any other USB devices in the DUO just in case you have any still attached.

Then try flashing it again,but try another USB port on the machine different as in one you have not already tried and then report back.

Just to let you know V2.0 have already had the Kernel 3.1.1 flashed so no need for anything like that at the moment also if your trying to flash Blackhole use 1.7.5 and below same with Vix use 2.4.155 and below.

Good luck

That was already quoted in post 11?

[DOUGALMCD]

Did you reboot box after successful flash? Try older version like bh1.6.7. You shouldn't have to do ic update or bootloader.

[digicon]

That was already quoted in post 11?

Not the Unplugging of the Hard Drive or using another USB slot was'nt

[digicon]

receiver never flashed, however loaded up after 10+ attempts starting > vu duo+ > saw bh 1.7.5 image then went to black screen, nothing functioning.

what should i do, install kernal or install icc security update bootloader

You may have to try Updating via the RS232 port with an .nfi image, as it appears the USB way is not working plus you could have corrupted the image on the nandflash

[DOUGALMCD]

Not the Unplugging of the Hard Drive or using another USB slot was'nt

Post 8 mentioned this although I should have added the word connected after everything else. You did just repeat everything I had said though.

[digicon]

Post 8 mentioned this although I should have added the word connected after everything else. You did just repeat everything I had said though.

Tell you what just keep editing your posts so that you thought of everything first

[DOUGALMCD]

You add something new when you post. Remember to read threads before posting.

[mdt]

flash this image with a RS232 null-modem lead then try reflashing your box with BH. 1.7.2 via usb stick,regards mdt Archive of Vu+

[digicon]

You add something new when you post. Remember to read threads before posting.

Mate at least i dont have to edit posts to make it look like i gave the right advice when i did'nt in the first place, you should actually read other threads about the subject as i actually posted the problems with the latest images on clones from the 9th of july. I suggest you do some homework before replying yourself.