VVDI PROG

[PocketHero]

clip are mostly for lazy people only, but i understand....it can save lot of time and work

And that matters @ roadside work. IT isn't funny to search for a fallen Spider (8 legged eeprom) on the black asphalt

[jaelgti]

Hello colleagues, someone who uses adapters for ezs.
I just bought them, and the first test w203 and I have this problem.
Has anyone tried it?
Thanks for your time

[PocketHero]

Has nothing to do with the adapter, except the bad contact. Release it, put it back, try again. Nothing dangerous.

[trinicolin]

Hello colleagues, someone who uses adapters for ezs.
I just bought them, and the first test w203 and I have this problem.
Has anyone tried it?
Thanks for your time

Look at the chip type on the other side of the PCB. Post picture.

Sent from my SM-G930F using Tapatalk

[daxxer]

Look at the chip type on the other side of the PCB. Post picture.

Sent from my SM-G930F using Tapatalk

on other side moostly 2J74Y

[ivyura1977]

Hello. Soft 4.8.0 BMW CAS4 1N35H chip not read and write after unlock success, force unclock too:
[2019-03-01 08:50:53] : Start communication...
[2019-03-01 08:50:53] : Chip is not crypt FE
[2019-03-01 08:50:53] : End communication...
[2019-03-01 08:50:53] : Operation success
[2019-03-01 08:50:56] : Check Device...
[2019-03-01 08:50:58] : 12V Power Adaptor connected
[2019-03-01 08:50:58] : Initialization device...
[2019-03-01 08:50:58] : Initialization success!
[2019-03-01 08:50:59] : Initialization chip...
[2019-03-01 08:50:59] : ID 0N35H 0XCC95/1N35H 0XCC95
[2019-03-01 08:51:00] : Chip is crypt,this operation needs to decrypt

Any ideas?

[habbyb]

Hello colleagues, someone who uses adapters for ezs.
I just bought them, and the first test w203 and I have this problem.
Has anyone tried it?
Thanks for your time

adapters work perfectly , check connection .

[jaelgti]

Has nothing to do with the adapter, except the bad contact. Release it, put it back, try again. Nothing dangerous.

Thank you very much for your cooperation, before publishing, I have connected and disconnected several times, cleaned the pcb and verified that the pins make contact.

[jaelgti]

And on the other side it's the same 4j74y

And say that the module works correctly.

[daxxer]

And on the other side it's the same 4j74y

And say that the module works correctly.

try to preheat the mecu which you want to read...its probably almost dead

[PocketHero]

Thank you very much for your cooperation, before publishing, I have connected and disconnected several times, cleaned the pcb and verified that the pins make contact.

Makes nothing, but try tó push down the clip when reading. Sometimes it helps.

[trinicolin]

on other side moostly 2J74Y

Zoom this area.

Sent from my SM-G930F using Tapatalk

[jaelgti]

Thank you very much for your interest colleagues

[WinWoj]

Somebody used fvdi to read older ezs from W208, W210 etc? xhorse doesnt produce adapters fro this ezs, but mcu cable could do this two Motorola MC68HC05X32 witfout desoldering, or only lifting reset leg?

[mrjackkilby]

can someone help me? to read tricore with vvdi prog? in suzuki swift sx4
please, thnks

Sent from my Redmi 4X using Tapatalk