View Full Version : Digiprog 3 clone questions and answers
pierre renault
13th September, 2013, 05:32 PM
Thank you !!
Nierka19
13th September, 2013, 07:44 PM
I try ford focus st27 for me is not work..
burko
13th September, 2013, 08:54 PM
sorry for double post
Anyone tested A6 (facelift) 2009-2010 dashboard with dp3 clone?
have done 2005-2008 dashes without problem
thank you in advance
Burko
TULGEYWOODMAN
13th September, 2013, 09:27 PM
sorry for double post
Anyone tested A6 (facelift) 2009-2010 dashboard with dp3 clone?
have done 2005-2008 dashes without problem
thank you in advance
Burko
anyone tried 2013 A6 with it?
javyb
13th September, 2013, 09:35 PM
anyone tried 2013 A6 with it?
Works a treat mate try it!
milesbetteroff
13th September, 2013, 09:37 PM
anyone tried 2013 A6 with it?
Not work just same as 2012 wants you to do EEPROM prepare first then Diag but don't work diagprog dp3 did it 5 mins witch is not the same as 2012 it must be differant in some way but looks the same !!!!!
smartymarti
14th September, 2013, 07:57 AM
Not work just same as 2012 wants you to do EEPROM prepare first then Diag but don't work diagprog dp3 did it 5 mins witch is not the same as 2012 it must be differant in some way but looks the same !!!!!
I don't understand the reply mate , its 2012 but its not the same as a 2012 ??? And are they 5 minute job in total or once you. Have stripped out and prepped EPROM
elzolee
14th September, 2013, 09:01 AM
2010 MB E-klass via OBD - OK
B-Klass Tacho diag via cable ST60- ok
s3man
14th September, 2013, 11:35 AM
Is it working with Audi a3 2011?
michalez
14th September, 2013, 11:44 AM
HC08 ---> ST42 Any chance to do it with digiprog 3 ?
javyb
14th September, 2013, 02:19 PM
HC08 ---> ST42 Any chance to do it with digiprog 3 ?
No hc08 not work with digi
eltiobarbas
14th September, 2013, 04:33 PM
Hi, after change mileage in Skoda Superb 2008 (Micronas) by OBD i have this error with VCDs 25-IMMO 00003 -Control Module Defective .
All working fine, car start, no lights ON in cluster..but i can't erase the DTC..when i clear appears again.
How can i fix this?
Regards
cotymoto
14th September, 2013, 04:54 PM
Where is the defect? Engine, cluster.remove battery negative 3 min and read with vag com and clear dtc.
Enviado desde mi LT30p usando Tapatalk 2
eltiobarbas
14th September, 2013, 05:01 PM
Where is the defect? Engine, cluster.remove battery negative 3 min and read with vag com and clear dtc.
Enviado desde mi LT30p usando Tapatalk 2
Hi, The Fault code its in the 25-immo module
01-Engine and 17-Cluster are fine, no DTS stored.
Ok , thanks i?ll remove the battery and check.
Regards
motorsport
14th September, 2013, 05:09 PM
Hi, The Fault code its in the 25-immo module
01-Engine and 17-Cluster are fine, no DTS stored.
Ok , thanks i?ll remove the battery and check.
Regards
Normal because you do mileage by obd and it cant erase all tool playing obd you will get this error
solution is by programer for not get this error
werner5395
14th September, 2013, 09:09 PM
Ford Fiesta 2013 by obd works perfekt
rukartinatv
14th September, 2013, 11:10 PM
Ford Fiesta 2013 9S12XEQ384
and cant not work with digiprog.
I dont know how do you did obd.
waldi1979
14th September, 2013, 11:24 PM
sorry for double post
Anyone tested A6 (facelift) 2009-2010 dashboard with dp3 clone?
have done 2005-2008 dashes without problem
thank you in advance
Burko
A6 2009FL OBD R/W OK.
sepistar
15th September, 2013, 09:50 AM
Ford Fiesta 2013 by obd works perfekt
wich sw.version you have?
br.
javyb
15th September, 2013, 11:21 AM
Ford Fiesta 2013 by obd works perfekt
Is it the new fiesta with new processor?
werner5395
15th September, 2013, 11:41 AM
its Ford Fiesta 5.2013 i do it with digiprog 4.82 version menu 2008- it works without problem.
Radley
15th September, 2013, 04:48 PM
VW Bora 1999,2000 via OBD ok
Audi A4 2000,2002,2004,2007,2009 via OBD ok
VW Passat 2006 ECU,DASH via OBD ok
VW Golf 1998 via OBD ok
rozario
15th September, 2013, 09:39 PM
a8 1998 via obd ok
passat 2005 via obd ok
a4 2007 via obd ok
xyznia
15th September, 2013, 10:13 PM
for bmw lcm modules use simple pa soft 1.4.0 adapter and you never need to remove module,tested many many times no problem, only 2min and job done!
michalez
16th September, 2013, 10:15 AM
No hc08 not work with digi
Support from china said that hc08 should work
Here is schema to connect
8
42/2
***30333;(white)
***40657;(black)
***32511;(green)
***26837;(brown)
***32418;(red)
***32418;(red)
***40657;(black)
***27225;(orange)
Anyone tried to do it?
s3man
16th September, 2013, 10:29 AM
Anyone know if it is working with late 2010 A3 or 2011? Thanks
sepistar
16th September, 2013, 10:59 AM
Anyone know if it is working with late 2010 A3 or 2011? Thanks
have done 2010,i can't remember if it was late 2010 or not.just try,see if dash are correctly identify.if yes give a try.
br.
TheBadFrog
16th September, 2013, 09:29 PM
I have a question,
from where can i actually buy a good Digiprog 3 clone without blue and white screen, new PCB (quality A) some people say, they are all from the same factory?
At the moment at aliexpress is Fw 4,82 included (is there a chance to update this tool without sending to seller?
I want to buy a set with obd and full cable set, at the moment the price start about 320 Dollar, OK?
Best regards
TheBadFrog
88diablo
16th September, 2013, 11:15 PM
Go to OBD factory and ask for one from yuanhua factory with green board. They are slightly more expensive but they are better quality. Ask for Joy as she knows this product.
jmcartec
16th September, 2013, 11:48 PM
Support from china said that hc08 should work
Here is schema to connect
8
42/2
***30333;(white)
***40657;(black)
***32511;(green)
***26837;(brown)
***32418;(red)
***32418;(red)
***40657;(black)
***27225;(orange)
Anyone tried to do it?
Sorry, i can't see this schematic connection! is that an encription for my eyes?
michalez
17th September, 2013, 08:18 AM
hc08 adapter42/2
orginal color clone color cable
(white) ---> (black)
(green) ---> (brown)
(red) ---> (red)
(black) ---> (orange)
i have 2 more cable in this adapter :
black cable with Condensator 10nF
and second black cable. Dont know for what it is...219790
bochen
17th September, 2013, 05:38 PM
hc08 adapter42/2
orginal color clone color cable
(white) ---> (black)
(green) ---> (brown)
(red) ---> (red)
(black) ---> (orange)
i have 2 more cable in this adapter :
black cable with Condensator 10nF
and second black cable. Dont know for what it is...219790
You have a starge clone because in mine there are colours as in original but HC08 programmer doesn't work.
sepistar
18th September, 2013, 06:38 AM
t5 1.9 2006
,dash went fine but edc 16 not.it work on it but wont change anything.
br.
jmcartec
18th September, 2013, 09:58 PM
About 74HC125D chips inside, did somebody exchanged them for 74HC125M?
This considering the reading of HC08
danihaos
19th September, 2013, 10:06 AM
Go to OBD factory and ask for one from yuanhua factory with green board. They are slightly more expensive but they are better quality. Ask for Joy as she knows this product.
Is OBD Factory a trustful seller? Do you have any experience with them? There is a tip to know that the product is from Yuanhua factory?
teerak2uk
19th September, 2013, 10:21 AM
Is OBD Factory a trustful seller? Do you have any experience with them? There is a tip to know that the product is from Yuanhua factory?
Yes I have bought from Lydia at obd factory but now find better price on alliexpress
TheBadFrog
19th September, 2013, 08:31 PM
Hello Tererak2uk, from which seller at aliexpress can we get the Yuanhua factory digiprog 3?Best regards i bought c4 mux from them, and this one i can not update (FW)
danihaos
20th September, 2013, 09:38 AM
I found at OBD Factory Yanhua tool with 308$ and Gocardiag 338$.
I saw muny people bought from Gocardiag and most of them are satisfied with them,but at OBD Factory is cheaper.
I'm not decided for seller OBD Factory or Gocardiag? What do you think?
skens
20th September, 2013, 10:55 AM
hi maybe help you
Car list:
Alfa 145 Programming via Chip
Alfa 146 Programming via Chip
Alfa 147/Chip86 Programming via Chip
Alfa 156 M2002 Programming Via Micro
Alfa 156HC11 Programming via Chip
Alfa 164 Only in our Office
Alfa 166 Model 2002 Programming Via Micro
Alfa 166HC11 Programming Via Micro
Alfa 166M 2002 Programming via Chip
Alfa Spider / GTV Only in our Office
Aston Martin DB7 Programming Via Micro
Aston Martin DB9 Program via cluster
Aston Martin Gallardo Programming Via Chip
Aston Martin Vanquish Programming Via Micro
Aston Martin Zagato Programming Via Micro
Audi A2/3/4/6 VDO 07/01 Diagnostic
Audi A2/3/4/6 VDO 07/01- Diagnostic
Audi A3 A8 2003 on Service & Navigation Diagnostic
Audi A3 to 06/01 Diagnosis
Audi A3 UKNSI Programmind Via Chip
Audi A4 Bosch 2002 Diagnostic
Audi A4 Modell 2001 Bosch Diagnostic
Audi A4 UKNSI Programmind Via Chip
Audi A8 / S8 up 02/99 Programming via Chip
Audi A8 24C16 Chip Programming via Chip
Audi A8 to 01/99 Diagnosis
Audi A8 VDO 2002 Programming via chip
Audi Audi A3/ A6/ A8 2006 on Diagnostic
Audi Jaeger/Magneti Marelli up 04/99 Diagnosis
Audi Magnetti Marelli All models Diagnostic
Audi MM 4/99 Diagnosis
Audi MM4/99 HC12 Programming Via Micro
Audi TT Diagnosis
Bentley Continental GT 2003 / Diagnostic
Bentley Continetal Program Via Chip
BMW 3 Series E46 2000 35080 Chip Programming Via chip
BMW 3 Series E46 Bosch 35080 Programming via chip
BMW 3er / Compact / Z3 Cluster-Diagnosis
BMW 3er / Compact / Z3 up 98 Cluster-Diagnosis
BMW 3er / E36 Diagnosis
BMW 3er / E36 Modell 99 Cluster-Diagnosis
BMW 3er / E46 1999/2000 Diagnostic
BMW 3er / E46 Lightmodule HC11 Programming via Chip
BMW 5er / E34 Programming via Chip
BMW 5er / E39 up 05/99 Programming via Chip
BMW 5er / E39 with BC to 04/99 Diagnosis
BMW 5er / E39 without BC to 04/99 Diagnosis
BMW 7er / E32 Programming via Chip
BMW 7er / E38 (SW 12/13) up 05/99 Cluster-Diagnosis
BMW 7er / E38 (SW 14) up 05/99 Programming via Chip
BMW 7er / E38 to 04/99 Diagnosis
BMW 7er up 10/01 Only in our Office / In progress
BMW 8er / E31 Diagnosis
BMW All CAS Units Send to office
BMW E39 LCM Diagnostic
BMW E39 Light Module All models Diagnostic
BMW E46 2001/ Light Module HC12 Diagnostic
BMW E46 2003/ Light Module HC12S Diagnostic
BMW E46 LCM Diagnostic
BMW E50 5 Series 2004 Diagnostic
BMW E60 & E65 E90 2004 2007 CAS Diagnostic
BMW F650GS Programming Via Chip
BMW Key Module & LCM all models Progarmming Via EWS
BMW Still R70 Programming Via Chip
BMW X3 Programming Via Chip & EWS LCM Diag
BMW X3 LCM Diagnostic
BMW X5 (SW 14 High) Programming via Chip
BMW X5 EWS & Key Programming Via EWS
BMW X5 LCM Diagnostic
BMW X5 Light module Diagnostic
BMW X5 Light module HS12 Diagnostic
BMW Z4 Programming Via Chip
BMW Z8 Programming via Chip
Cagiva Raptor 1000 Programming Via Chip
Chevrolet Avalanche Programming Via Micro
Chevrolet Balzer Programming Via chip
Chevrolet Corvette Programing Via Chip
Chevrolet Corvette Programming Via chip
ChevroletTahoe Programming Via chip
ChevroletTrail Blazer 95020 Programming Via chip
Chrysler 300 HC12 Programming Via Micro
Chrysler 300M Programming via Chip
Chrysler All Models Diagnostic
Chrysler Cherokee Modell 2002 Diagnostic
Chrysler Cherokee to Chip 56 Programming via Chip
Chrysler Crossfire Diagnostic
Chrysler Grand Cherokee 04/99 Diagnostic
Chrysler Grand Cherokee C86 Program via chip
Chrysler Grand Cherokee HC12 Diagnostic
Chrysler Grand Cherokee to 03/99 Diagnosis
Chrysler Le Baron Only in our Office / In progress
Chrysler Neon HC12 Programming via Chip
Chrysler PT Cruiser HC12 Diagnostic
Chrysler PT Cruiser to HC11 Diagnoctic
Chrysler Seebring HC12 Programming via Cluster
Chrysler Stratus Diagnosis
Chrysler Voyager Modell 2002 HC12 Cluster-Diagnosis
Chrysler Voyager to Bj. 2001 Diagnosis
Chrysler Wrangler Programming via Chip
Chrysler Wrangler HC11 Programming via Micro
Citreon C3 Programming Via Tacho & Box
Citreon C5 Programming Via Box & Cluster
Citreon C5 2003 Programming Via chips
Citreon C8 Programming Via Tacho & BSI
Citreon New Saxo Diagnostic
Citreon Picasso NEC Tacho & Box Via Micro & Chip
Citreon Relay Van Chip 95040 Programming Via Chip
Citreon Xsara 2000/2002 NEC Programming Via Chips BSI & Tacho
Citroen Belingo 2003/2004 Programming Via cluster & BSI
Citroen Belingo HC08 Tacho Programming Via Micro
Citroen C3 Programming Via Chip
Citroen C5 New software Programming Via Cluster & BCM
Citroen C8 Programming Via Tacho & BSI
Citroen Evasion Programming via Chip
Citroen Relay Programming Via Chip
Citroen Xantia Programming via Chip
Citroen Xsara Programming via Chip
Citroen Xsara Programming Via BCU & Tacho
Daimler Benz 300C Programming Via Micro
Daimler Benz A-Klasse Diagnosis
Daimler Benz C/Klasse (W203) 07/2003 Diagnostic Via cluster
Daimler Benz C/Klasse (W203) 2001/2002 Diagnostic Via cluster
Daimler Benz C-Klasse (W202) Diagnosis
Daimler Benz C-Klasse (W203) 07/003 Diagnosis
Daimler Benz CLK / SLK to 03/99 Diagnosis
Daimler Benz CLK / SLK up 04/99 Diagnosis
Daimler Benz E-Klasse to 03/99 Diagnosis
Daimler Benz E-Klasse up 04/99 Diagnosis
Daimler Benz G Klasse Programmingg Via Box
Daimler Benz G-Klasse to 03/99 Diagnosis
Daimler Benz G-Klasse up 04/99 to 07/01 Diagnosis
Daimler Benz G-Klasse up 08/01 Diagnosis
Daimler Benz M-Klasse to 03/99 Diagnosis
Daimler Benz M-Klasse up 04/99 to 07/01 Diagnosis
Daimler Benz M-Klasse up 08/01 Diagnosis
Daimler Benz S-Klasse Diagnosis
Daimler Benz S-Klasse (W220 ) up 06/02 Programming via Chip & Key
Daimler Benz S-Klasse (W220) to 05/01 Programming via Chip
Daimler Benz SL 2002 Programming Via Key & chip
Daimler Benz SL-Klasse R129 Diagnosis
Daimler Benz SL-Klasse R130 Programming via Chip
Daimler Benz Smart 2004 Programming Via Tacho & BSI
Daimler Benz Sprinter Cluster-Diagnosis
Daimler Benz Sprinter Modell 2000 Programming via Chip
Daimler Benz Vaneo Programming Via Cluster
Daimler Benz Vito Vaneo Model 2003 on Programming Via Tacho & Key module
Daimler Benz Vito VDO Cluster-Diagnosis
Daimler Benz V-Klasse / Magneti Marelli Diagnosis
Daimler Benz V-Klasse VDO Cluster-Diagnosis
Daimler Benz W203 W211 Key module HC12S Only in our office
Daimler Benz W209 CLK / SLK up tp 08/03 Diagnostic
Daimler Benz W211 2004 Key & Gateway Only in our office
Daimler Benz W211 2004 Service Assyst Only in our office
Daimler Benz W211 E Class SW 77 Diagnostic
Daimler Benz W211 E Class up to Sept 2003 Diagnostic
Dodge Durango Programming via Chip
Dodge Ram 2003 Diagnostic
Ferrari 430 Program via chip
Ferrari 550M Programming Via Chip
Ferrari ENZO Scagletti Programming via chip
Ferrari F50 Only in our Office / In progress
Ferrari F50 Programming Via Chip
Ferrari F650 Programming Via Chip
Ferrari Modena 360 Programming Via Chip
Ferrari Stradale Programming Via Chip
Fiat Brava ST Cluster-Diagnosis
Fiat Bravo MM08 Programming Via Micro
Fiat Bravo NS56 Programming Via Micro
Fiat Daily VDO Chip Programming Via Chip
Fiat Ducato M2002 NEC Programming Via Chip
Fiat Duplo Model 2002 Programming via Chip
Fiat Iveco Daily Programming via Chip
Fiat Marea 2004 Programming via Micro
Fiat Marea 2004 Programming Via Chip
Fiat Marea HC11 Programming Via Micro
Fiat Multipla Cluster-Diagnosis
Fiat Multipla M2002 C56 Programming Via Chip
Fiat Panda Programming Via Chip
Fiat Panda Programming Via Chip
Fiat Panda Chip 95040 Program via chip
Fiat Punto 2002 NEC Programming via Chip
Fiat Punto Jeager 08 Cluster-Diagnosis
Fiat Scudo Programming via Chip
Fiat Seicento Programming Via Chip
Fiat Stilo Programming Via Chip
Fiat Stilo Programming Via Micro
Fiat Ulysee 2004 Programming Via Tacho & BSI
Fiat Ulysse Programmin Via Micro
Ford Connect Programming Via Micro
Ford Connect Programming Via Chip
Ford Cougar Cluster-Diagnosis
Ford Explorer Programming Via Micro
Ford Explorer 2003 Programming Via Micro
Ford F150 2004 Programming Via Micro
Ford F150 HC11 Programming Via Micro
Ford F250 HC12 Programming Via Micro
Ford F350 Program Via Cluster
Ford Feista 2003 Programming Via Chip
Ford Feista 9S12 2006 model Programming Via BDM
Ford Fiesta Cluster-Diagnosis
Ford Focus Cluster-Diagnosis
Ford Focus 2003 Chp & Micro all models Programmin Via chip Or BDM Points
Ford Fusion Programming Via Chip
Ford Fusion Progarmming Via Chip
Ford Galaxy Diagnosis
Ford Galaxy 2000/2006 Diagnosis
Ford Maverick HC11 Programming Via Micro
Ford Mondeo Cluster-Diagnosis
Ford Mustang Programming Via Micro
Ford Puma Cluster-Diagnosis
Ford Ranger Programming Via Cluster
Ford Scorpio Cluster-Diagnosis
Ford Tarus 2003/ Only in our office
Ford Thunderbird 2005/ 2006 model Programming Via BDM
Ford Transit 2003 Programming Via chip
Ford Transit 2004 Programming Via Micro
Ford Transit Model 2003 Programming Via Chip
Ford Transit TVI Chip 66 Progarmming Via Chip
Ford VAN F150 Programming via Chip
Ford Windstar HC11 Programming Via Micro
GM Cadillac Programming Via Chip
GM Cadillac Seville STS Chip Programming via Chip
GM Cadillac Seville STS HC 11 Cluster-Diagnosis
GM Corvette Chip 93C76 Programming via chip
GM Hummer Programming via Chip
GM Hummer 2006 Programming via Tacho & Box
GM Hummer Klms & Hours Programming Via Chip
GM Seville HC11 Programming Via Micro
GM Trans Sport HC12 Programming Via Micro
GM Transport M99 Programming Via Micro
HARLEY Davidson Buel Programming via Chip
Honda Accord Programming via Chip
Honda Accord Type R Programming Via Chip
Honda CBR 1000RR Programming Via Chip
Honda CBR400 Programming Via Chip
Honda Civic Programming via Chip
Honda CRV 2004 Chip 56 Programming Via Chip
Honda CRV Chip 93C56 Programming Via Chip
Honda CRV HC12 Programming Via PCB
Honda HRV Programming via Chip
Honda Jazz Programming Via Chip
Honda Jazz Programming Via chip
Honda Legend Programming via Chip
Honda Logo programming Via Chip
Honda S 2000 Programming via Chip
Honda Shutle Programming via Chip
Honda Stream Programming Via chip
Honda VFR 800 93C46 Programming Via Chip
Hummer Miles & Hours Programming Via chip
Hyundai Coupe Ch 46 Programming Via Chip
Hyundai Getz Programming Via Chip
Hyundai Matrix Ch 46 Programming Via Chip
Hyundai Sante Fe Ch56 Programming Via Chip
Hyundai XG 30 Ch 46 Programming Via Chip
Hyundia Accent Programming Via Chip
Isuzu Trooper Programming via Chip
Jaguar Daimler to 12/97 Cluster-Diagnosis
Jaguar Daimler up 01/98 Cluster-Diagnosis
Jaguar S Type 2005 Program Via Cluster
Jaguar S Type HC12 Programming Via PCB
Jaguar S-Type 2002 HC12 Programming via Micro
Jaguar S-Type to 09/01 Programming via Micro
Jaguar S-Type up 10/01 Programming via Micro
Jaguar XJ 350 Programming Via Micro
Jaguar XK8 Programming via Micro
Jaguar Xtype HC12 Programming Via PCB
Kawasaki GPZ 600 93C46 Programming via Chip
Kawasaki ZX9 93C46 Programming via Chip
Kia Carnival Programming Via Chip
Kia Sorrento Programming Via Chip
Kia Sorrento Programming Via Chip
Lamborghini Gallardo Programming Via Chip
Lancia Lybra Programming via Chip
Lancia Z Programming via Chip
LDV Convoy Van Programming Via Chip
Lexus LS 200 Programming via Chip
Lexus LS 300 Programming via Chip
Lexus LS 400 Programming via Chip
Lexus LS 430 Programming via Chip
Lexus RX300 Programming via Chip
Lincoln Navigator Programming via Chip
Lincoln Navigator 2003 Programming Via Micro
Lotus Elise HC11 Programming Via Micro
Maserati Quattroporte Programming Via chip
Mazda 3 Programming Via Chip
Mazda 323 Programming via Chip
Mazda 6 Programming Via Chip
Mazda 6 Programming Via Chip
Mazda 626 Programming via Chip
Mazda 626 2003 Programming via Chip
Mazda MPV Programming via Chip
Mazda MX5 Programming via Chip
Mazda Premecy Programming via Chip
Mazda RX7 Programming via Chip
Mazda RX8 Programming Via Tacho
Mazda TRIBUTE HC11 Programming Via Micro
Mitsubishi Carisma Programming via Chip
Mitsubishi Colt Programming via Chip
Mitsubishi Eclipse Programming Via Chip
Mitsubishi Galant Programming via Chip
Mitsubishi Grandis Programming Via Chip
Mitsubishi Lancer Programming via Chip
Mitsubishi Outlander Programming via Chip
Mitsubishi Pajero Programming via Chip
Mitsubishi PININ Ch 46 Programming via Chip
Mitsubishi Shogun Ch 56 Programming via Chip
Mitsubishi Space Gear Programming via Chip
Mitsubishi Space Runner Programming via Chip
Mitsubishi Space Star Programming via Chip
Mitsubishi Space Wagon Programming via Chip
Motor Cycles
Nissan Almera 93C46/C56/C66 Programming via Chip
Nissan Infinity Programming via Chip
Nissan Maxima Programming via Chip
Nissan Micra Programming via Chip
Nissan Navaro Programming via Chip
Nissan Pathfinder Programming via Chip
Nissan Pathfinder HC12S Program Via Cluster
Nissan Patrol Programming via Chip
Nissan Pick Up Programming via Chip
Nissan Primera Programming via Chip
Nissan Primera 2004 Programming Via Chip
Nissan Primera 93C56/ C66 Programming Via Chip
Nissan Skyline R34 Programming Via Chip
Nissan Skyline R35 & GT350 Programming Via Chip
Nissan Skyline R35 350GT Programming Via Chip
Nissan Terrano II Cluster-Diagnosis
Nissan Tino Programming Via Chip
Nissan Xtrail Programming Via Chip
Nissan Xtrail C66 Programming Via Chip
Opel Astra Diagnosis
Opel Corsa Diagnosis.
Opel Frontera Programming via Chip
Opel Montery Programming via Chip
Opel Movano Programming Via Chip
Opel Vectra 04/99 Diagnosis
Opel Vectra 2003/2007 Programming Via chip
Opel Vectra to 03/99 Diagnosis
Opel Vivaro M2002 NEC Programming via Chip
Opel Zafira Diagnosis
Opel Zafira 2003./2007 Diagnostic
Peugeot 106 Diagnostic
Peugeot 206 Jaeger Programming Via Micro
Peugeot 206 M2002 NEC All new models Programming Via Chip
Peugeot 306 VDO Cluster-Diagnosis
Peugeot 307 Chip Programming Via Box & Tacho
Peugeot 307 HC12 Programming Via Micros
Peugeot 406 Jaeger Programming Via Micro
Peugeot 406 Sagem Programming via Chip
Peugeot 406 Valeo Box Programming Via Box & Cluster
Peugeot 406 VDO Cluster-Diagnosis
Peugeot 406 VDO 2000/2001 Cluster + BCU
Peugeot 407 Programming Via Tacho & BSI
Peugeot 607 VDO Programmingg Via Box + Cluster
Peugeot 806 Jaeger / Magneti Marelli Programming Via Micro
Peugeot 807 Programming Via Tacho & BSI
Peugeot BOXER Programming Via Chip
Peugeot Partner Programming Via Chip
Porsche 928 Programming via Chip
Porsche 996 09/01/2000 Diagnostic
Porsche 996 2000/2002 BCU Programming Via Box
Porsche 996 to 08/01 Diagnosis
Porsche 996 Turbo Ready Soon
Porsche 996 up 09/01 93C86 Diagnostic
Porsche 997 MCU Program via chip
Porsche 997 Tacho & MCU Programming Via Chips
Porsche Boxster Diagnosis
Porsche Cayenne Diagnostic
Porsche Cheyenne Programming Via Chip
Renault Clio 2004 Programming Via Chip
Renault Clio Jaeger / Magneti Marelli Programming Via Micro
Renault Clio M2002 NEC Programming via Chip
Renault Clio Sagem Programming via Chip
Renault Espace Model 2004 Programming Via Tacho & BSI
Renault Espace to 01/99 Only in our Office / In progress
Renault Espace up 02/99 Programming Via Micro
Renault Espace up 2003 Ch 56 Programming via Chip
Renault Kangoo Programming via Chip
Renault Laguna HC12 Programming Via Micro
Renault Laguna Jaeger Programming via Chip
Renault Laguna MM08 Programming Via Micro
Renault Laguna Sagem Programming via Chip
Renault Laguna ST Micro Programming Via Micro
Renault Master Programming Via Chip
Renault Megane Jaeger / Magneti Marelli Programming Via Micro
Renault Megane Sagem to 09/99 Programming via Chip
Renault Megane Sagem up 10/99 Only in our Office / In progress
Renault Megane Senic Sagem Only in our Office / In progress
Renault R25 Programming via Chip
Renault Safrane Programming via Chip
Renault Traffic Programming Via Micro
Renault Twingo Programming Via Micro
Rolls Royce All Models Only in our Office
Rover 25/45 Programming Via Chip
Rover 75 Programming via Chip
Rover 75 LCM Diagnostic
Rover 75 Light Module Diagnostic
Rover Defender Programming via Chip
Rover Discovery TD5 Programming Via BCU
Rover Freelander to 05/01 Programming via Chip
Rover Freelander to 06/02 Only in our Office / In progress
Rover Landrover Programming via Chip
Rover MGF Programming via Chip
Rover MGTF 2003/2004 Programming Via Micro
Rover Mini Cooper 2 Models up to Sept 2003 Programming Via Cluster & Box
Rover Range Rover Programming via Chip
Rover Range Rover 2001/2002 Programming via chip
Saab 900 Not Implemented
Saab 9-3 Programming via Chip
Saab 93 24C02 Programming Via chip
Saab 93 9S12 Programming Via BDM
Saab 93 Model 2003 All models Programming Via Chip
Saab 9-5 Programming via Chip
Sang Yong Rexton Programming Via Chip
Seat All Diagnosis
Seat Altea Diagnostic
Seat Leon Diagnostic
Seat Toledo Diagnostic
Sko bia 2002 Diagnostic
Skoda Octavia Service inspection & Klms Diagnostic
Smart Four four Cluster & BSI Programming Via Chip & Micro
Smart Smart All models Tacho & BSI Programming Via Box & Cluster
Subaru Forester Programming via Chip
Subaru Impreza Programming via Chip
Subaru Legacy Programming via Chip
Subaru Tribeca Programming via chip
Susuki Liana Programming Via Chip
Suzuki Ignis Programming Via Chip
Suzuki Ignis Programming Via Chip
Suzuki Jimny Programming via Chip
Suzuki Liana 2005 Program via chip
Suzuki TL 1000S Programming via Chip
Suzuki Vitara Programming via Chip
Toyota Avensis Diagnosis
Toyota Avensis 2004 Programming Via chip
Toyota Camry Programming via Chip
Toyota Cellica Programming via Chip
Toyota Corolla Programming via Chip
Toyota Corrolla VDO Programming via chip
Toyota Hi Ace Programming via Chip
Toyota HJ 100 Programming Via Chip
Toyota IGNIS Programming Via Chip
Toyota K95 Programming via Chip
Toyota Land Cruiser 2003 C66 Programming Via Chip
Toyota Landcruiser Programming via Chip
Toyota Landcruiser 2003 Ch66 Programming via Chip
Toyota MR 2 Programming via Chip
Toyota Picnic Programming via Chip
Toyota Prado Programming via chip
Toyota Previa Programming via Chip
Toyota Prious Programming Via Chip
Toyota RAV4 Programming via Chip
Toyota Yaris Programming via Chip
Toyota Yaris Tsport Programming via Chip
Vauxhall Astra 2004 Programming Via Chip
Vauxhall Astra 2004 Programming Via Chip
Vauxhall Meriva Diagnostic
Vauxhall Movano Programming Via Chip
Vauxhall Speedster Programming Via Chip
Vauxhall Vectra 2004 Programming Via Chip
Volvo S40 / V40 Programming via Chip
Volvo S60 / V60 Programming via Chip
Volvo S80 up 02/99 Cluster-Diagnosis
Volvo V40 Model 2003 on Programming Via Chip
Volvo V50 Programming Via Micro
Volvo V60/V70/V80. Model 2002 Programming Via Micro
Volvo V70 2002 HC12 Cluster-Diagnosis
Volvo V70 to 01/99 Programming via Chip
Volvo V70 up 02/00 Cluster-Diagnosis
Volvo V70 up 02/99 to 01/00 Cluster-Diagnosis
Volvo V70 V2 HC12 Cluster-Diagnosis
Volvo XC 70 2003/2004 Programming Via Micro
Volvo XC 90 2003/2004 Programming Via Micro
Volvo XC70 2004 Model Programming Via Micro
Volvo XC90 2004 Model Programming Via Micro
VW Bora Diagnosis
VW Caddy Cluster-Diagnosis
VW Caddy 2005 Diagnostic
VW Corrado Cluster-Diagnosis
VW Crafter Programming Via Chip
VW Golf 3 Cluster-Diagnosis
VW Golf 4 Diagnosis
VW Golf 4 24C08 Chip Programming Via Chip
VW Golf 4 All models Diagnostic
VW Golf Mk 5 up to August 2006 Diagnostic
VW Golf Visteon Diagnostic
VW Golf5 Up to August 2006 Diagnostic
VW LT Cluster-Diagnosis
VW Lupo Diagnosis
VW New Beetle Diagnosis
VW New Sharan Diagnosis
VW Passat B3 Cluster-Diagnosis
VW Passat B5 Diagnosis
VW Passat B6 up 12/00 Diagnosis
VW Pheaton Bosch Diagnostc
VW Polo Diagnosis
VW Polo 2003 Diagnostic
VW Sharan Diagnosis
VW Sharan 2006 model Diagnostic
VW T4 Bus Cluster-Diagnosis
VW Taro Cluster-Diagnosis
VW Touareg Diagnostic
VW Touran Service Inspection Diagnostic
VW Vento Cluster-Diagnosis
Wiesmann Roadster Programming via chip
Yamaha R6 Programming Via Chip
Yamaha R6 Programming via Chip
Yamaha VTR 1000 93C46 Programming via Chip
Yamaha Wild Star 93C46 Programming via Chip
Yamaha YZF-R1 93C46 Programming via Chip
honingkoning
20th September, 2013, 06:48 PM
What is this, dont post such bull.
Wbr.
hawaj81
21st September, 2013, 08:10 AM
Where best to buy digiprog 3? So that work can and line K?
Buy PCB green or blue? Is the color of connectors black or gray?
I've read all about it and still do not know where to buy?
And if at any digiprog the line K vag group shows instead of miles "???"
mario313
21st September, 2013, 12:43 PM
HONDA CRV 2012 - 93C76 - OK
g-ziro
21st September, 2013, 04:05 PM
CLONE DIGIPROG BLUE/BLANC SCREENi need help, my clone-DP3 show me Blue/Blanc Screen. :beheaded:
g-ziro
21st September, 2013, 04:11 PM
CLONE DIGIPROG BLUE/BLANC SCREEN
i need help, my clone-DP3 show me Blue/Blanc Screen. :beheaded:
PremierD
21st September, 2013, 04:34 PM
So two posts .. you have two clones then .. are they both gubbed lol
TULGEYWOODMAN
21st September, 2013, 07:43 PM
CLONE DIGIPROG BLUE/BLANC SCREENi need help, my clone-DP3 show me Blue/Blanc Screen. :beheaded:
well buy another one, they are cheap enough.
danielboom00
21st September, 2013, 09:32 PM
Chrysler sebring 2000 OBD read & write ok as stratos model,
U have to disconect battery after do it to see the correction
Somebody knows how to do 2002 chevy monte carlo? Tachosoft says 912B32 but i need bdm points or diagram.
Thanks
Enviado desde mi iPad con Tapatalk HD
rozario
21st September, 2013, 10:33 PM
audi a6 2006 via obd ok
audi a4 2004 rb4 via obd ok
nenadrossi
22nd September, 2013, 01:16 AM
Does anyone know how to do audi a3 2007 -? Edit mileage, then remove the battery, then back, then write new mileage. One way or something else?
blacktoy
22nd September, 2013, 10:26 AM
hi,
Does someone have a working shematic for ST60 connector?
many thx in advance
br
cotymoto
22nd September, 2013, 12:46 PM
CLONE DIGIPROG BLUE/BLANC SCREEN
i need help, my clone-DP3 show me Blue/Blanc Screen. :beheaded:
Enviado desde mi Woxter Tablet PC 50BL DUAL usando Tapatalk 2
looly
23rd September, 2013, 11:28 AM
Anyone tried doing a fiat ducato van with digiwigi pls?
88diablo
23rd September, 2013, 01:44 PM
Anyone tried doing a fiat ducato van with digiwigi pls?
Hi yes done a 2008 OBD fine.
davecooper47
23rd September, 2013, 09:25 PM
Done 2009 obd no problem.
andersonmaxi
24th September, 2013, 12:59 AM
hey mates what abt vw polo 2012 and golf 2012 nec95320 inside dash Anyone tried doing with digiwigi mean digiprog3
thx mates dk
justy22
24th September, 2013, 01:31 AM
I have done a few 12 plate polos no trouble takes about 1 to minute read and 1 minute to write back , not tried 12 plate golf
g-ziro
24th September, 2013, 06:44 AM
I have done a few 12 plate polos no trouble takes about 1 to minute read and 1 minute to write back , not tried 12 plate golf
Golf 12 and Polo 12 ist Not the Same ....
Sent from my iPhone using Tapatalk - now Free (http://tapatalk.com/m?id=1)
bersch8688
24th September, 2013, 06:45 AM
Skoda Fabia 2012 ---> use mode Skoda Octavia Diag ;-)
g-ziro
24th September, 2013, 06:49 AM
Skoda Fabia 2012 ---> use mode Skoda Octavia Diag ;-)
Right like Touran mode Golf 5 /6 Diag ;-)
Sent from my iPhone using Tapatalk - now Free (http://tapatalk.com/m?id=1)
skens
24th September, 2013, 11:24 AM
CLONE DIGIPROG BLUE/BLANC SCREEN
i need help, my clone-DP3 show me Blue/Blanc Screen. :beheaded:
hi
page to help
http://obd2repair.skyrock.com/3140096344-How-to-solve-Digiprog-III-Blue-White-Screen-problem.html
1 This might be solution to fix blue screen on digiwigi
Unsolder U16 and U17 from the board, and solder CY7C1049D onto the board at the same place.
regards
AlexandruP
24th September, 2013, 11:46 AM
Your link no work, see below working one
How to solve Digiprog III Blue/White Screen problem? : (http://www.obd2repair.com/news/how-to-solve-digiprog-iii-bluewhite-screen-problem-a-315.html)
skens
24th September, 2013, 11:56 AM
hi
i try now,work perfekt!
regards
g-ziro
24th September, 2013, 12:12 PM
hi
page to help
http://obd2repair.skyrock.com/3140096344-How-to-solve-Digiprog-III-Blue-White-Screen-problem.html
1 This might be solution to fix blue screen on digiwigi
Unsolder U16 and U17 from the board, and solder CY7C1049D onto the board at the same place.
regards
1- Thanks
2- link not function
3- I have test this method, nothing changed
http://img.tapatalk.com/d/13/09/24/je9y7yzy.jpg
An other idea .....
Sent from my iPhone using Tapatalk - now Free (http://tapatalk.com/m?id=1)
PremierD
24th September, 2013, 04:22 PM
Is it A Blue/white screen when you plug ino a vehicle ? or only when powering on the bench ?
g-ziro
24th September, 2013, 10:13 PM
Is it A Blue/white screen when you plug ino a vehicle ? or only when powering on the bench ?
If i power on its show me bluescreen. Nothing is change with changing chip.
Sent from my iPhone using Tapatalk - now Free (http://tapatalk.com/m?id=1)
PremierD
24th September, 2013, 10:14 PM
I meant mate .. are you using the 12volt supply ? or plugging it into a vehicle ?
skens
25th September, 2013, 12:01 PM
hi
MERCEDES - W203 (C) - DIAG -7_01 with ST60
1 Remove the tacho from the car
2 used ST60 as a PDF MERCEDES - W203 (C) - DIAG -7_01 , DP3 it says 49
3 adjust connector or download wrapper and connect
4 panel lights up
5 used menu w203 -7/2001
6 does not read original miles
7 Enter the desired km, work 15 min
8 back in the car, you do not need to work and box"EZS"
Radley
25th September, 2013, 12:48 PM
Hi somebady try Vw Crafter 2011? is chance to make ezs via DP3? Thanks in advance
teerak2uk
25th September, 2013, 02:44 PM
Hi somebady try Vw Crafter 2011? is chance to make ezs via DP3? Thanks in advance
I'd use a blocker personally
teerak2uk
25th September, 2013, 02:44 PM
Hi somebady try Vw Crafter 2011? is chance to make ezs via DP3? Thanks in advance
I'd use a blocker personally
vageric
25th September, 2013, 02:51 PM
I'd use a blocker personally
and witch blokker is that?
carbandit
25th September, 2013, 02:59 PM
blocker for a 9s12 ??? why when you can read and write with r260 /smok jtaq etc ... nec mcu is for blocker not motorola unless cas 4 secured
anyway regarding crafter you will need to do ezs with r260 or smok .. .but tacho can be done by diggiwiggi
michalez
25th September, 2013, 03:13 PM
it possible to copy eeprom bin from clone v4.82 to pc ? i tried to connect but without any sucess :/ Pc cant see digiprog ... any solutions?
andersonmaxi
25th September, 2013, 03:27 PM
hello mates
somebady try new clio 4 ??
thx u
andersonmaxi
25th September, 2013, 03:28 PM
hello mates
somebady try new clio 4 ??
thx u
Radek2000000
25th September, 2013, 08:11 PM
Audi A6 2006 dash work( test only if is read i not change it)---What to do?
michalez
25th September, 2013, 08:55 PM
if it read correctly change mileage
andersonmaxi
25th September, 2013, 10:06 PM
hello mates
somebady try new clio 4 by digiprog3 ??
thx u
g-ziro
25th September, 2013, 10:20 PM
Hi somebady try Vw Crafter 2011? is chance to make ezs via DP3? Thanks in advance
If you have original DP3/XPROG-M EZS is possible.
With clone DP3 no chance.
Sent from my iPhone using Tapatalk - now Free (http://tapatalk.com/m?id=1)
honingkoning
26th September, 2013, 09:31 AM
Clone xprog also works great or clone r260.
michalez
26th September, 2013, 10:47 AM
Hi,
I have problem with my connection digiprog with pc. Pc doesnt find anything when i connect usb. Pc term is activated. Any solution? I check voltage from digiprog usb and there is 0v. I Bought digiprog from nandtools.com but i think they are down and i cant ask them. I send photo pcb maybe someone have the same digiprog and know what to do.
I look into another pcb in internet and i saw that they have chip ( see pic) This chip is for usb connection? my chip is missing
gregc83
26th September, 2013, 12:24 PM
I did , its about 25 mins
skens
26th September, 2013, 01:37 PM
hi
transporter T5, 2012 obd not work
regards
exe123
26th September, 2013, 02:07 PM
Hi,
I have problem with my connection digiprog with pc. Pc doesnt find anything when i connect usb. Pc term is activated. Any solution? I check voltage from digiprog usb and there is 0v. I Bought digiprog from nandtools.com but i think they are down and i cant ask them. I send photo pcb maybe someone have the same digiprog and know what to do.
I look into another pcb in internet and i saw that they have chip ( see pic) This chip is for usb connection? my chip is missing
The missing chip is FT232BL USB-TTL. Solder it in and PC will detect the digiprog
kappaca
26th September, 2013, 07:27 PM
hello guys someone ever made zs c 204 2011 I can not change I set a fixed value as the new value, however, the old values ***8203;***8203;remain.
digiprog3
RCS
26th September, 2013, 08:43 PM
Hi,
I have problem with my connection digiprog with pc. Pc doesnt find anything when i connect usb. Pc term is activated. Any solution? I check voltage from digiprog usb and there is 0v. I Bought digiprog from nandtools.com but i think they are down and i cant ask them. I send photo pcb maybe someone have the same digiprog and know what to do.
I look into another pcb in internet and i saw that they have chip ( see pic) This chip is for usb connection? my chip is missing
Here is the picture of the unit that works properly...
Sent from my iPad using Tapatalk HD
ohkarol
27th September, 2013, 11:26 AM
Lancia Musa 2005 by obd2 - OK.
sashxxx
27th September, 2013, 06:40 PM
Mitsubishi Colt 2010 93cs66 via clip - OK!
Radley
28th September, 2013, 02:58 PM
Hi Skoda Octavia 2012 by OBD ok
gijsvm
29th September, 2013, 12:09 AM
Digiprog 4.88 f****d up a Audi TT 2008 today.
Did same model few months ago and work, this time it makes a black dash.
javyb
29th September, 2013, 09:40 AM
Digiprog 4.88 f****d up a Audi TT 2008 today.
Did same model few months ago and work, this time it makes a black dash.
Plug digi in again and try to correct miles it should work
nenadrossi
29th September, 2013, 01:48 PM
Lancia Lybra 2002 , problem in mileage correction with DigiProg3 chica clone!!!
Plug 35 , soldering wires to the board ,its operating instructions digiprog3.
Blue wire remains free. Read mileage, 4 billion, 172 230 write, then read 172 230 . I was happy !
Fit them on the car, mileage 0!!
Reread 172 230, 172 452 write, then read 172 452, instead of the car, again 0!
What do I do??? please help me.
xyznia
29th September, 2013, 03:29 PM
if you see wrong mileage after reading ori file NEVER correct mileage,first read and save all eeprom or mcu memory with other eeprom programmer like UPA-USB, Xprog etc.... dashboard may have few different algorythms,you can lost original data after change mileage.
gijsvm
29th September, 2013, 07:19 PM
Plug digi in again and try to correct miles it should work
I did more than once. But nothing works anymore.
Also try with enigma tool to repair flash, nothing...
Than read out complete flash by hand with smok jtag, and send directly to smok engineer.
After that i build dash back into car and in the time i build it in smok make extra function in his xcan soft to repair this kind of TFT dash by obd.
And work !! and dash came alive !!
wiseman
30th September, 2013, 04:28 AM
I did more than once. But nothing works anymore.
Also try with enigma tool to repair flash, nothing...
Than read out complete flash by hand with smok jtag, and send directly to smok engineer.
After that i build dash back into car and in the time i build it in smok make extra function in his xcan soft to repair this kind of TFT dash by obd.
And work !! and dash came alive !!
When you first did this car a few month previously was it with 4.82 ?
lupu_sandu
30th September, 2013, 08:22 AM
Lancia Lybra 2002 , problem in mileage correction with DigiProg3 chica clone!!!
Plug 35 , soldering wires to the board ,its operating instructions digiprog3.
Blue wire remains free. Read mileage, 4 billion, 172 230 write, then read 172 230 . I was happy !
Fit them on the car, mileage 0!!
Reread 172 230, 172 452 write, then read 172 452, instead of the car, again 0!
What do I do??? please help me.
Don't try with Digiprog, will not work.
Read/write with UPA on back of dash. Works perfectly.
gijsvm
30th September, 2013, 09:50 AM
When you first did this car a few month previously was it with 4.82 ?
Yes was with 4.82. But also other car with other soft and other HW from dash. This one was with TFT screen.
Even after i repair flash and corrected mileaged with xcan(multiTool) i did try to read it out again with enigma, but also unknown version.
Only one that was happy was smok engineer because he add new car in his tool.
88diablo
30th September, 2013, 01:36 PM
Digi just done 2012 Merc W218 fine that Abrites couldnt block sync on.
AlexandruP
30th September, 2013, 01:57 PM
Better was to send logs to ABRITUS72 and they add to machine.
88diablo
30th September, 2013, 02:08 PM
Yes but I read another post that someone tried that and they got told to fit blocker still. Plus just curious to see if Digi could do it.
PremierD
30th September, 2013, 02:11 PM
The old wiggy can do anything .. and for a fraction of the cost .. whats not to like :)
88diablo
30th September, 2013, 02:19 PM
The old wiggy can do anything .. and for a fraction of the cost .. whats not to like :)
Nothing! Thats why I just liked it.
TULGEYWOODMAN
30th September, 2013, 04:51 PM
The old wiggy can do anything .. and for a fraction of the cost .. whats not to like :)
old wiggy [whigs] for prime minister.......................................... .................................................. .................................................. ...... [unless you want david cameron for first choice of course, cos he looks after you all]:eek:
PremierD
30th September, 2013, 04:59 PM
Wiggy would be better than the plank of ****in wood you have in there at the moment , in fact tin of chick peas would even do better , and I don't care if you're a Tory or not .lol
nenadrossi
30th September, 2013, 07:23 PM
Can the Lancia with Carprog?? Do not raise mileage with Fiat ECU scan??
bersch8688
1st October, 2013, 06:39 AM
Please help
My ST15 for VW T4 Dash not working.
Please to repair
sepistar
1st October, 2013, 08:18 AM
Please help
My ST15 for VW T4 Dash not working.
Please to repair
search on forum mate,there are pinout for all connectors.
br.
Mexaniks
2nd October, 2013, 09:17 AM
who knows the manufacturer's website Digiprog3 in China? Not sellers. send me a pm
skens
2nd October, 2013, 09:57 AM
Please help
My ST15 for VW T4 Dash not working.
Please to repair
hi
T4 -2010 work to obd
regards
Mexaniks
2nd October, 2013, 10:56 AM
hi
T4 -2010 work to obd
regards
K-line problems
sepistar
2nd October, 2013, 05:12 PM
hi
T4 -2010 work to obd
regards
it must be T5 m8,did the ecu too?
br.
skens
3rd October, 2013, 09:15 AM
hi
I have not tried it, customers sought only tacho
regards
javyb
3rd October, 2013, 09:24 AM
it must be T5 m8,did the ecu too?
br.
You can't do ecu on a 2010 as it's most likely gonna be EDC17
sepistar
3rd October, 2013, 02:25 PM
You can't do ecu on a 2010 as it's most likely gonna be EDC17
yes,you may have right.but i found edc 16 on early 2010.(probably was 2009 and model 2010),but on ecu not goes with digiwigy.
br.
maaxxyy
3rd October, 2013, 10:16 PM
I done a 2011 T5 today, took about 5 minutes to do, very easy.
g-ziro
4th October, 2013, 01:35 AM
I meant mate .. are you using the 12volt supply ? or plugging it into a vehicle ?
I use 12 Volt from supply.
Sent from my iPhone using Tapatalk - now Free (http://tapatalk.com/m?id=1)
angelcom
4th October, 2013, 02:02 AM
Hi, mercedes W204 by OBD, works ok just choose ezs option, read and write ok 2 min
RCS
4th October, 2013, 03:12 AM
opel insignia 2011 OBD does not work
will try other options tomorrow...
PremierD
4th October, 2013, 06:53 AM
I use 12 Volt from supply.
Sent from my iPhone using Tapatalk - now Free (http://tapatalk.com/m?id=1)
Then try plugging into a vehicle .. ( I had the same fault ) it was the power supply plug.. at fault .. nothing to lose by trying mate lol
sepistar
4th October, 2013, 12:48 PM
I done a 2011 T5 today, took about 5 minutes to do, very easy.
do you mind the ecu?
br.
88diablo
4th October, 2013, 01:45 PM
do you mind the ecu?
br.
Done a few T5 dash fine but could never get ECU to go diag.
maaxxyy
4th October, 2013, 09:24 PM
Didnt see the option for ecu on T5
cotymoto
4th October, 2013, 09:32 PM
Ford focus 2005 perfect 2 min. Diag.
Enviado desde mi LT30p usando Tapatalk 2
sepistar
5th October, 2013, 09:02 AM
Didnt see the option for ecu on T5
there aren't t5 ecu option,but some of them work under golf-passat option.
br.
88diablo
5th October, 2013, 09:13 AM
There is ECU option on mine.
kappaca
6th October, 2013, 07:21 AM
of digiprog c option is ECU?
you can read edc16?
drpeter
6th October, 2013, 06:34 PM
Bit late on this but e65 side of the lead the tracks have been cut because chinkys made the pcb wrong repair it and try. Not saying it will work ? The top 2 tracks at the top near j3 just want repairing but solder other 2 wires in correct place, will try one if it comes in Someone tried this cable? I added the wires but no power on digi, I opened the 25pin connector and I think the white wire is connected to the wrong pin (to pin 12 instead of pin 25 +). My connections are 13 black 12 white 10 red 9 orange. If someone can check the white one for me it would be great. Thanks.
werner5395
8th October, 2013, 09:22 PM
DB W204 2008 Dash show 78000km ezs show on digiprog by obd 1800000 km can i do this with digiprog or must i go other way? Please help. thx
88diablo
8th October, 2013, 09:33 PM
DB W204 2008 Dash show 78000km ezs show on digiprog by obd 1800000 km can i do this with digiprog or must i go other way? Please help. thx
Maybe already been done before.
PremierD
8th October, 2013, 11:12 PM
Yes mate .. the wiggy will work :)
teerak2uk
9th October, 2013, 08:29 AM
Anyone tried 2013 vw touran on v4.82 to save me a wasted 20 mile trip as the guy don't want to bring it to me
88diablo
9th October, 2013, 08:33 AM
Done a late 2012 caddy maxi life which is very similar if that helps.
drpeter
9th October, 2013, 08:51 AM
Anyone tried 2013 vw touran on v4.82 to save me a wasted 20 mile trip as the guy don't want to bring it to me Save your trip will not work, 2013 vag update needed.
Mexaniks
9th October, 2013, 09:19 AM
I want to buy an upgrade. Who can update Digiprog 3 to version 4.91 or 4.92. please PM !!!I am only interested in the version 4.91 or 4.92 <only>!!! I'm not a salesman! I want to buy an upgrade.
tomuch
9th October, 2013, 01:22 PM
I want to buy an upgrade. Who can update Digiprog 3 to version 4.91 or 4.92. please PM !!!I am only interested in the version 4.91 or 4.92 <only>!!!
Me too
Gesendet von meinem GT-I9505 mit Tapatalk 2
skens
9th October, 2013, 01:50 PM
hi
AUDI A6 2006- DIAG obd ok! meni AUDI , A6 2004 (4F) read km,write new ok
regards
TULGEYWOODMAN
9th October, 2013, 06:20 PM
I want to buy an upgrade. Who can update Digiprog 3 to version 4.91 or 4.92. please PM !!!I am only interested in the version 4.91 or 4.92 <only>!!!
speak to George at Milton Keynes:roflmao:
drpeter
9th October, 2013, 07:35 PM
Me too
Gesendet von meinem GT-I9505 mit Tapatalk 2 You want tomuch
skens
10th October, 2013, 03:12 PM
HI
HYUNDAI - ACCENT 2005 C56 PLUG 1,read,write ok
regards
skens
10th October, 2013, 03:14 PM
hi
FIAT - DUCATO2006 - 950X0. PLUG 1,read,write ok
regards
skens
10th October, 2013, 03:18 PM
hi
FIAT - DOBLO 2002 NEC, 950X0. PLUG 1,read,write ok
regards
skens
10th October, 2013, 03:22 PM
hi
RENAULT - KANGOO CHIP 76.PLUG 1,read wrong km,I not experimented changed
regards
tomuch
10th October, 2013, 08:05 PM
You want tomuch
Dont think so we will see
Gesendet von meinem GT-I9505 mit Tapatalk 2
cotymoto
10th October, 2013, 09:49 PM
Nissan navara 2004 93c56. Not working.
Enviado desde mi LT30p usando Tapatalk now Free ('http://tapatalk.com/m?id=10')
bersch8688
11th October, 2013, 06:35 AM
Work Digiprog on
Ford Fiesta HCS12 ST48 ??????
Thank you
cheero
11th October, 2013, 08:02 AM
version v4.92 is OK
Audi :
A1 new version Diag
Chevrolet :
Aveo Diag
Spark C86
Citroen :
Jumper 2007 -Diag
Fabia :
Roomster new version Diag
Fiat :
Ducato 2007 -Diag
Doblo 2007 -Diag
Lancia :
Thema 24c16
Landrover :
Evoque Diag
Mercedes :
Modell W212 Face Lift Modell 2014 Diag
Modell R230 new version Diag
Modell R172 Diag
Modell 176 Diag
Modell R231 Diag
Modell W246 Diag
Modell 117 Diag
Aprilia :
RSV1000 24C02
Ducati :
Monster24C02
autocargo
11th October, 2013, 08:54 AM
There's already version v4.92 on the clones? I've fallen way behind :))
cheero
11th October, 2013, 09:01 AM
yes for eu clone, no for china clone :)
cheero
11th October, 2013, 09:08 AM
here is foto of my clone eu digiprog
cheero
11th October, 2013, 10:56 AM
digiprog eu clone sell in CZ
price is cca 2250 usd
update is only for this eu clone !
sepistar
11th October, 2013, 11:17 AM
think it took not to long until the chinese update for these clone will be available.
br.
skens
11th October, 2013, 02:58 PM
hi
Peugeot boxer 2007- DIAG obd ok! menu Fiat Ducato -2007 read km,write new ok
regards
makadam
14th October, 2013, 10:46 PM
Can I make odometer correction on Passat B6 2006y on both in ECU and instrument panel or only in instrument?
88diablo
14th October, 2013, 10:55 PM
Should do both easily on that year.
teerak2uk
14th October, 2013, 11:07 PM
[QUOTE=makadam;2118872]Can I make odometer correction on Passat B6 2006y on both in ECU and instrument panel or only in instrument?[/UOTE]
Dash via obd but depending on ecu maybe ecu only by clip
diagtech
14th October, 2013, 11:18 PM
Hi has anyone got digiprog that is broke that is willing to sell me the touchscreen dropped mine and cracked corner of screen thanks
chrismoore02
15th October, 2013, 12:21 AM
Hi has anyone got digiprog that is broke that is willing to sell me the touchscreen dropped mine and cracked corner of screen thanks
You can buy the screen on its own from China mate. :)
diagtech
15th October, 2013, 12:57 AM
Done a search and they seem to be for elprosys dp3 not clone and if they are for clone it is $159 i have ordered another clone but just wondered if anyone had a screen
smartymarti
15th October, 2013, 07:54 AM
Pm me your details , I know some one with one that went blue screen ???
michalez
15th October, 2013, 10:26 AM
i got problem with honda crv 2008 c76. Milage read ok but cant do right km
cheero
15th October, 2013, 10:36 AM
i have eu clone and Honda CRV 2008 and 2009 with eeprom 93c76 no problem, read and write via 3M clips, work ok
motorsport
15th October, 2013, 11:03 AM
i have eu clone and Honda CRV 2008 and 2009 with eeprom 93c76 no problem, read and write via 3M clips, work ok
On board or you unsolder chip?
michalez
15th October, 2013, 11:48 AM
i unsolder chip. i have saved eeprom but i cant write it back with digiprog. It show changed eeprom now with wrong calculated km. eetool program cant transfer file (there is no file c76 in eetool) I will connect now with xprog-m and write eeprom from digiprog handly and then changed with nyo4 or other program
motorsport
15th October, 2013, 12:19 PM
i unsolder chip. i have saved eeprom but i cant write it back with digiprog. It show changed eeprom now with wrong calculated km. eetool program cant transfer file (there is no file c76 in eetool) I will connect now with xprog-m and write eeprom from digiprog handly and then changed with nyo4 or other program
maybe you have bad clip change for original pomona and check all wire it will work very good
michalez
15th October, 2013, 01:10 PM
i think that digiprog destroyed my dump. I have readed before with eeprom digiprog but not works. Now milage is not correct and functions of dashboard wrong ( fuel 0 , water coolent 0, engine control etc) . Have someone Eu dump honda crv 93c76 2008?
PremierD
15th October, 2013, 01:22 PM
" i think that digiprog destroyed my dump." ... did the clone jump up and press the read funtion then mate .. :) now if you had removed the eep .. then it would have beed more difficult for it to **** ... :)
michalez
15th October, 2013, 01:34 PM
" i think that digiprog destroyed my dump." ... did the clone jump up and press the read funtion then mate .. :) now if you had removed the eep .. then it would have beed more difficult for it to **** ... :)
can you give me advice what to do now ?
PremierD
15th October, 2013, 01:50 PM
I may have a dump .. let me look
PremierD
15th October, 2013, 02:26 PM
Its a newer dump mate .. but I don't think that they are different .. (its better than the one you have at the moment ) :)
michalez
15th October, 2013, 03:12 PM
Its a newer dump mate .. but I don't think that they are different .. (its better than the one you have at the moment ) :)
Your dump works!!. Thank you very much ;*;*;*;* Now my client will test functions. Millage is little to small :) 11000 km. I think i will try again do milage with digiprog. Now i have only yellow control engine but i dont have for now computer to delete it.
Apolo29
15th October, 2013, 04:50 PM
Edit dump to km you want!!!
teerak2uk
15th October, 2013, 05:03 PM
Edit dump to km you want!!!
If you dare pmsl or better still ask someone nicely to do it for you
michalez
15th October, 2013, 05:19 PM
I nicely ask for help :) it will be better if someone will do it for me, 125500 km it will be great. economizer fuel i think doesnt work i hope that when i will delete errors from cluster everything will be ok.
in attachments there is 2 files please help to change km to 125500 km
sorry guys for offtopic and my mistakes...
Apolo29
15th October, 2013, 08:05 PM
Sorry i thought you knew the procedure. I have changed Premierd dump to 125500km.
michalez
16th October, 2013, 09:11 PM
Sorry i thought you knew the procedure. I have changed Premierd dump to 125500km.
thanks you very much :) i saved dash with your help :)
I have one question - anybody now what do function " COUNTER" in setup digiprog?
auris
18th October, 2013, 08:16 AM
Hi!
Cable 51\2 for HC12 damaged bsi in Crysler Voyager 2002.
Now i repaired this adapter and work perfect.
mototun
18th October, 2013, 02:57 PM
digiprog eu clone sell in CZ
price is cca 2250 usd
update is only for this eu clone !
the 4.92 works also on chinese clones
is it possible to change the device serial number?
m_yura
19th October, 2013, 07:19 AM
yes you can change the serial number
TULGEYWOODMAN
19th October, 2013, 11:36 AM
I'd use a blocker personally
2 blockers?
TULGEYWOODMAN
19th October, 2013, 11:57 AM
now hear this........now hear this.............
old pensioner does w212...
customer rings back a week later asking for value to be increased a little [his mistake]
pensioner agrees to do this for free.
but pensioners DP3 goes tits up and has to go back to Poland.
pensioner has abrites, but latest update has bugs in it.Pensioners attempts to increase value using abrites, but ends up fu****g up gateway!
pensioner gets his good friend to reflash gateway on line with star.
pensioner still has problem of increasing value.
pensioner updates abrites to latest version of software but is still not convinced it will be ok.......what shall he do?
Luckily, pensioner has "young " friend called Arthur who is very wise.
Few weeks ago Arthur suggested that pensioner should buy v4.85 digiprog clone.....pensioner didnt like this idea at first, thinking it was "Devils work",but after speaking to a couple of ****neys, decided to buy one,it arrived very quickly.
After much dice throwing, dart throwing, lucky number picking, the pensioner decided to risk using the new "devil box" on customers w212
"Well oil beef hooked", the pensioner said as the "devil box" did the job in 1 minute without drama!
The pensioner would like to apologise to all forum members for slagging off clones and will now take all his original tools to the boot sale and reduce his prices to whatever the forum members charge.
thankyou and goodnight.
PremierD
19th October, 2013, 01:49 PM
lol Nice one Eric ... lol
rukartinatv
19th October, 2013, 04:56 PM
Vw passat 12/12
vw jetta 12/11
Work with out any problem with v4.88
smartymarti
19th October, 2013, 07:19 PM
Eric I'm shocked you've gone to the yellow side
CARPARTS
19th October, 2013, 07:46 PM
Eric I'm shocked you've gone to the yellow side
Next step for Eric will be a home visit to Andersonmaxi.
davecooper47
19th October, 2013, 08:26 PM
Luv ya Eric!!! One of my mentors!!!! Takes a big man to moonwalk like Jackson!!!! One of the points I always made was : everyone is slagging off this piece of kit but tell me??? How many of you haven't ever owned a Diga clone????? Same thing, different era!!!! I like to think I am one of the ****neys mentioned.
makadam
19th October, 2013, 11:48 PM
But I need correct information that someone do it with this tool!
sepistar
20th October, 2013, 05:02 AM
ha,ha..luckily that the old pensioner has such a good young friends who give him a very good advice mate...and once again the clone did the job before the king of tools.
br.
vageric
20th October, 2013, 08:34 AM
yes but did the clone match the ezs to dash mileage or put it on 1.6 million mileage?
TULGEYWOODMAN
20th October, 2013, 11:16 AM
yes but did the clone match the ezs to dash mileage or put it on 1.6 million mileage?
The guy needed it by Monday 10am.
What would you have done in the circumstances?
As a matter of interest NOTHING writes the correct kms to the ezs!
and yes, I checked with star and all kms where correct.
I always ensure kms are correct in battery sensor, tyre pressure monitor, adaptive brake,soot entry, particle filter, ecu,assyst plus, assyst,airbag hours,seat belt actuations,electric seat where applicable, instrument cluster,ezs [although only flashed].
cotymoto
20th October, 2013, 01:12 PM
Bmw 530 1999. Diag not working. Software12.
Enviado desde mi LT30p usando Tapatalk
TULGEYWOODMAN
20th October, 2013, 01:42 PM
Bmw 530 1999. Diag not working. Software12.
Enviado desde mi LT30p usando Tapatalk
I have used the tacho universal [clone again] with success on some E39 BMW
djnesio
20th October, 2013, 03:00 PM
Ford C-Max 1.6 TDCi 90bhp 2007
Works correctly by OBD in 1 minute.
TULGEYWOODMAN
20th October, 2013, 04:33 PM
Eric I'm shocked you've gone to the yellow side
My word Martin, you do look well in that avatar picture.
When I spoke to you on the phone the other day I could hardly understand your Brummie accent.
[you said "yallow soyd" ]:roflmao:
bersch8688
22nd October, 2013, 01:20 PM
Fiat Doblo 2006 ---> OBD Work Read ---> NOT WRITE
Need write with EEPROM Clip
bersch8688
22nd October, 2013, 04:25 PM
Renault Master 2010 ---> eeprom clip 93C76 Work
danielboom00
23rd October, 2013, 03:48 AM
Hey mates,
I need help with a 2000 Vw new beetle with 912d60 i tried by obd because somebody before me put on 0 and i'm trying to put in 75000 miles, by obd i can't put more than 10000 or goes to 0 again, and i'm trying now to read with cable 48 but digi says not conected...
It's my second car with digi and i don't know exactly which is the problem
Thanks in advance
Enviado desde mi iPad con Tapatalk HD
Music73
23rd October, 2013, 05:52 AM
Ford Fusion 2012 works by OBD if you tell it it's a Fiesta -2008
Radley
23rd October, 2013, 07:00 AM
Audi TT 2008 via OBD
VW Golf R 2010 via OBD
Wys***322;ane z mojego GT-I8190 przy u***380;yciu Tapatalka
Timing
23rd October, 2013, 02:04 PM
digiprog eu clone sell in CZ
price is cca 2250 usd
update is only for this eu clone !
Please where to buy this eu clone. Thank you
xyznia
23rd October, 2013, 09:47 PM
same master 2011 93c76 not work,shows right km value but after change nothing changes in dash,i did it with upa by my self using kangoo tachosoft calc
bersch8688
23rd October, 2013, 10:14 PM
same master 2011 93c76 not work,shows right km value but after change nothing changes in dash,i did it with upa by my self using kangoo tachosoft calc
Renault Master 2010 yesterday WORK 100% EEPROM Clip
Hazzard
24th October, 2013, 08:30 AM
AudiTT 2010,golf 6 2009,audi a4 2008new model OBD change km,Ok very exselent,very good mashine?
fif
24th October, 2013, 03:10 PM
Audi Q7, 2009, s-line, by OBD OK, time 20 min.
skens
24th October, 2013, 03:27 PM
Digiprog 3 V4.85 Update Service Digiprog 3 V4.85 Update Service - $88.00 : go car diagnostic , scanner , car , auto scanner, car diagnose, diagnostic tools (http://gocardiag.com/index.php?main_page=product_info&cPath=72&products_id=746)
for BMW:
F20
F30
for Citroen:
C3/DS3 new versions
for Dodge:
Charger 24C16
for VW : Diag new version
for Fiat:
for Fiorino 95080/ECU95320
for Ducato/for Punto 95160
for Land rover:
for Evoque 93C76
for Mazda:
3 C66
for Mercedes :
for Crafter/for Sprinter EZS new versions
for Mitsubish:
for Lancer new version
for Nisan:
for Qashqai 2011 HCS12
370Z C86
for Renault:
for Scenic 24c16+ABS
gregc83
25th October, 2013, 03:21 PM
Hey mates.
someone was doing opel insignia , BSI also needs to be done? it is works by OBD ? the same question applies to opel zafira 2006
thanks
twincam
25th October, 2013, 04:01 PM
In insignia you are doing only bsm but diggi not working on some versions.Zafira needs to be done manual with desoldering memory from dash and in this model mileage is also in ecu.
sashxxx
25th October, 2013, 04:23 PM
When for free ?? :)
chrismoore02
25th October, 2013, 04:47 PM
What about v4.88?
PremierD
25th October, 2013, 04:52 PM
THEY ALL WANT ****IN JAM ON IT .... Free and 4.88 ... why not just ask for 4.92 for free ....
chrismoore02
25th October, 2013, 04:55 PM
I never mentioned free :rolleyes:
But now you mention it yeah what about 4.92 lmao
bersch8688
25th October, 2013, 06:27 PM
i wanted Update 4.92 for my DigiProg
Contact PM
tibi85
25th October, 2013, 06:58 PM
I want to make an Audi A6 (year 2004) via obd cable. But I have heard that the ecu also has information about the milage. It is true? If it is, the digiprog3 can correct it too?
thanks for helping!
PremierD
25th October, 2013, 07:05 PM
i wanted Update 4.92 for my DigiProg
Contact PM
UPDATE FOR DIGI 4.92 (http://www.tacho.de/)
Repinator
25th October, 2013, 09:17 PM
VW Passat B6 2007 ECU,DASH via OBD ok
CAS3 E61 LCI 530i Touring 04/2009,via CAS plug not OK (shows right SW,HW version but after, nothing changes in CAS) :(
Golf3 MotoMeter via dash plug not OK
Ford Focus 2001 with HC11 via dash plug not OK
twincam
26th October, 2013, 06:40 PM
SSangYong Rexton dash 9s12 with repaired st48 =all OK.
kizagt
26th October, 2013, 07:02 PM
Bmw e36 318is 1992 year via diagnostic plug OK
ohkarol
27th October, 2013, 08:33 AM
Ford Focus with HC11 via dash plug --- OK :)
Repinator
27th October, 2013, 09:32 AM
Ford Focus with HC11 via dash plug --- OK :)
For me it did not work
Can my cable is defekt
You can put a photo of your cable open?
Thanks
teerak2uk
27th October, 2013, 10:01 AM
For me it did not work
Can my cable is defekt
You can put a photo of your cable open?
Thanks
Or you could search the thread yourself
ohkarol
27th October, 2013, 10:41 AM
ST 27 TYCO-M1026-S502
yellow 10 11
green 9 9
brown 13 blue 1
white 25 14, 16
i comapred this pinout to my cable and it's correct
sashxxx
27th October, 2013, 01:41 PM
DB25 25,14 to 16 or 25 to 14,16 ??
ST 27 TYCO-M1026-S502
yellow 10 11
green 9 9
brown 13 blue 1
white 25 14, 16
i comapred this pinout to my cable and it's correct
ohkarol
27th October, 2013, 04:16 PM
db25's 25 to 14dash and16 dash.
it's the power supply
skens
28th October, 2013, 03:01 PM
hi
maybe help
ST CAS CANON25
blue 9 26
blue/white 10 35
black 13 12
red 25 34
ST 1 clip 3M 923650-08
1 1
2 2
3 3
4 4
19 5
6 6
5 7
7 8
ST 4 clip 3M 923690-08
1 1
2 2
3 3
4 4
19 5
6 6
5 7
7 8
ST 37
yellow 9 yellow
green 10 green
white 25 13
yellow 25 2
brown 13 1
ST 33
yellow 10 6
green 9 8
brown 13 1 blue
grey 25 10
white 25 9
ST 2 Dil 8
1 1
2 2
3 3
4 4
5 6
6 7
7 5
13 8
ST 55 TYCO-M1026-S502
green 17 green
yellow 18 yellow
white 25 11
brown 13 8
grey 25 7
ST 11 9695 9695/50
yellow 9 1
green 10 15
white 12 1 12
brown 13 11
ST 36 AMP 20pin
yellow 9 yellow
green 10 green
white 17 blue
brown 13 black 16
yellow 25 15
white 25 14
ST 29 AMP964825
yellow 9 yellow
green 10 green
brown 13 brown 17
white 25 1
yellow 25 2
ST 10
green 9 18
yellow 9 15
white 12 3
brown 13 1
ST 20 TYCO-M1026-S502 AMP92850-2
green 9 5
yellow 10 1
white 12 15
grey 12 16
brown 13 10
green 22 1
ST 12 Box
yellow 9 1
green 10 2
brown 13 3
brown 13 4 (R 1k0)
ST 49 PCB
green 9 green
yellow 10 yellow
white 12 white
brown 13 brown
ST 39 TYCO-M1026-S502 TYCO-M1026-S502
brown 7 brown
yellow 9 yellow
green 10 green
white 25 white
brown 13 23 11
green 25 24
white 25 22
yellow 25 20
ST 51
brown 13 brown
green 17 green
yellow 18 yellow
white 25 white or 06 reset
ST 26 TYCO-M1026-S502(white) TYCO-M1026-S502 AMP1-828917-2
green 9 12
yellow 12 23
yellow 12 16
white 12 4
white 12 22
brown 13 3
brown 13 24
yellow 22 8
ST 21 TYCO-M1026-S502 Peugeot (grey)
yellow 9 1
green 10 2
white 12 13
yellow 12 9
green 12 17
brown 13 11
ST 38 yellow 9 yellow
green 10 green
brown 13 brown
brown 13 2
white 25 14
yellow 25 22
ST 23 AMP343865
green 9 14
yellow 10 13
brown 13 3
white 25 2
grey 25 5
ST 32
yellow 9 yellow
green 10 green
white 12 white
brown 13 brown
ST 35
yellow 9 yellow
green 10 green
brown 13 black
grey 17 blue
white 25 red
ST 7 TYCO-M1026-S502 Peugeot (3pin)
white 10 2
brown 13 17
yellow 15 1
green 16 3
white 25 4
ST 27 TYCO-M1026-S502
yellow 10 11
green 9 9
brown 13 blue 1
white 25 14, 16
ST 46 TYCO-M1026-S502
brown 1 brown
yellow 9 yellow
green 10 green
brown 13 19
white 20 white
green 25 17
white 25 1
ST 19
green 9 8
yellow 12 5
brown 13 4
white 25 7
ST 31 AMP 1-963 616-1
yellow 9 1
green 10 2
white 12 9
brown 13 1
ST 34
blue 1 blue
green 2 green
yellow 3 yellow
orange 4 orange
black 5 black
brown 13 brown
red 25 red
ST 6 BMW
green 9 19
yellow 10 14
brown 13 15
white 12 20
ST 22 TYCO-M1026-S502
green 9 23
white 12 25
grey 12 24
brown 13 26
yellow 13 13
AMP 1-963 616-1
ST 43 green 9 16
yellow 10 15
grey 12 17
white 12 9
brown 13 18
pink 13 10
ST 47
white 1 white
yellow 2 yellow
brown 3 brown
blue 4 blue
black 5 black
red 6 red
grey 7 grey
green 19 green
ST 42
grey 1 grey, Condensator 10nF
white 6 blue
green 9 green
brown 13 black
yellow 20 white
white 25 red
ST 41 AMP 964825 - green AMP 964825 - blue
green 9 28
brown 13 9
green 17 black
yellow 18 green
white 25 1
yellow 25 23
ST 28 AMP-929650-2
yellow 9 yellow
green 10 green
brown 13 11
white 20 white
yellow 25 10
white 25 5
ST 9+15 AMP1-963553-1(24pin) 191972530B(28pin)
yellow 4 13
R-10k 9
green 10 7
white 10 2
brown 13 5
brown 13 9
brown 13 1
yellow+R 14 4
green 15 3
white 25 1
white 25 13
grey 25 17
ST 48
yellow 18 yellow
green 17 green
white 7 white
brown 13 brown
skens
28th October, 2013, 03:09 PM
digiprog3-adapter
ST01 8 Pin SOIC Clip
ST04 8 Pin Dill Chip Clip
ST06 BMW OBD Diagnostic Plug
ST07 BMW Compact SW7
ST08 Mercedes Benz C Class VDO 1993/1995 ST08 ST09 ST15 ST18
ST09 VW Golf 3 MM Cluster Diagnostic
ST10 Mercedes Benz OBD Diagnostic Plug
ST11 Mercedes Benz S Class Cluster Diagnostic
ST12 Mercedes Sprinter Kienzle Diag nostic plug
ST13 Digiprog Power Lead
ST14 Audi A6 Diag 1994/1996 & ST17 Audi A6 Diag 1994/1996
ST15 ST18 VW Golf Mk3 VDO Cluster Diagnostic
ST16 OBD II Diagnostic
ST19 Mercedes Sprinter VDO Cluster diagnostic
ST20 BMW 5/7 Series Cluster Diagnostic
ST21 Toyota Avensis Cluster Dignostic
ST22 Peugeot 306 VDO Cluster Diagnostic
ST23 Jaguar XJ6 11DU 90/91/93/95
ST24 Data lead for ST16
ST25 Ford Scorpio Cluster Diagnostic
ST26 BMW 3 Series Compact SW9/10
ST27 Ford Focus
ST28 Peogeot 206 Jeager
ST29 Ford Feista Mk 3 & 4 up to year 2000
ST30 Smart car BSI
ST31 Peugeot 406 VDO Cluster Dianostic
ST32 Fiat Multipla
ST33 Alfa 156 HC11
ST34 Alfa 145/146 ST
ST35 HC11 lead this is used on sevral applications
ST36 Alfa
ST37 Jaguar XK8
ST38 Ford Couger
ST39 Peugeot 806 Citreon Synergy, Fiat ScudoCable Title
ST41 Audi MM Dash cluster lead
ST42 This lead has sevral applications
ST45 Chrysler Grand Cherokee 1999/2000 Cluster Dignostic
ST46 Peugeot 406 Jeager
ST47 This lead has sevral applications
ST49 Mercedes W203 Diagnostic
ST50 Mercedes A Class HC 12 & Vaneo
ST51 HC12 Micro lead
ST55 Jaguar X Type
ST60 W211 & W203 Cluster Diagnostic
POWER 12V DC
ST-bmw
Saulius Saulius
28th October, 2013, 03:25 PM
Hi, maybe someone have Digiprog 3 instructions in English?
teerak2uk
28th October, 2013, 03:32 PM
Hi, maybe someone have Digiprog 3 instructions in English?
I use bing translator just google it mate and then nitro PDF to edit the files and save as English
Saulius Saulius
28th October, 2013, 03:51 PM
it is possible do mercedes e211 2007 with clone digiprog? need hc12 adapter , but I not have in my set of cables...
Repinator
28th October, 2013, 04:51 PM
hi
maybe help
ST CAS CANON25
blue 9 26
blue/white 10 35
black 13 12
red 25 34
ST 1 clip 3M 923650-08
1 1
2 2
3 3
4 4
19 5
6 6
5 7
7 8
ST 4 clip 3M 923690-08
1 1
2 2
3 3
4 4
19 5
6 6
5 7
7 8
ST 37
yellow 9 yellow
green 10 green
white 25 13
yellow 25 2
brown 13 1
ST 33
yellow 10 6
green 9 8
brown 13 1 blue
grey 25 10
white 25 9
ST 2 Dil 8
1 1
2 2
3 3
4 4
5 6
6 7
7 5
13 8
ST 55 TYCO-M1026-S502
green 17 green
yellow 18 yellow
white 25 11
brown 13 8
grey 25 7
ST 11 9695 9695/50
yellow 9 1
green 10 15
white 12 1 12
brown 13 11
ST 36 AMP 20pin
yellow 9 yellow
green 10 green
white 17 blue
brown 13 black 16
yellow 25 15
white 25 14
ST 29 AMP964825
yellow 9 yellow
green 10 green
brown 13 brown 17
white 25 1
yellow 25 2
ST 10
green 9 18
yellow 9 15
white 12 3
brown 13 1
ST 20 TYCO-M1026-S502 AMP92850-2
green 9 5
yellow 10 1
white 12 15
grey 12 16
brown 13 10
green 22 1
ST 12 Box
yellow 9 1
green 10 2
brown 13 3
brown 13 4 (R 1k0)
ST 49 PCB
green 9 green
yellow 10 yellow
white 12 white
brown 13 brown
ST 39 TYCO-M1026-S502 TYCO-M1026-S502
brown 7 brown
yellow 9 yellow
green 10 green
white 25 white
brown 13 23 11
green 25 24
white 25 22
yellow 25 20
ST 51
brown 13 brown
green 17 green
yellow 18 yellow
white 25 white or 06 reset
ST 26 TYCO-M1026-S502(white) TYCO-M1026-S502 AMP1-828917-2
green 9 12
yellow 12 23
yellow 12 16
white 12 4
white 12 22
brown 13 3
brown 13 24
yellow 22 8
ST 21 TYCO-M1026-S502 Peugeot (grey)
yellow 9 1
green 10 2
white 12 13
yellow 12 9
green 12 17
brown 13 11
ST 38 yellow 9 yellow
green 10 green
brown 13 brown
brown 13 2
white 25 14
yellow 25 22
ST 23 AMP343865
green 9 14
yellow 10 13
brown 13 3
white 25 2
grey 25 5
ST 32
yellow 9 yellow
green 10 green
white 12 white
brown 13 brown
ST 35
yellow 9 yellow
green 10 green
brown 13 black
grey 17 blue
white 25 red
ST 7 TYCO-M1026-S502 Peugeot (3pin)
white 10 2
brown 13 17
yellow 15 1
green 16 3
white 25 4
ST 27 TYCO-M1026-S502
yellow 10 11
green 9 9
brown 13 blue 1
white 25 14, 16
ST 46 TYCO-M1026-S502
brown 1 brown
yellow 9 yellow
green 10 green
brown 13 19
white 20 white
green 25 17
white 25 1
ST 19
green 9 8
yellow 12 5
brown 13 4
white 25 7
ST 31 AMP 1-963 616-1
yellow 9 1
green 10 2
white 12 9
brown 13 1
ST 34
blue 1 blue
green 2 green
yellow 3 yellow
orange 4 orange
black 5 black
brown 13 brown
red 25 red
ST 6 BMW
green 9 19
yellow 10 14
brown 13 15
white 12 20
ST 22 TYCO-M1026-S502
green 9 23
white 12 25
grey 12 24
brown 13 26
yellow 13 13
AMP 1-963 616-1
ST 43 green 9 16
yellow 10 15
grey 12 17
white 12 9
brown 13 18
pink 13 10
ST 47
white 1 white
yellow 2 yellow
brown 3 brown
blue 4 blue
black 5 black
red 6 red
grey 7 grey
green 19 green
ST 42
grey 1 grey, Condensator 10nF
white 6 blue
green 9 green
brown 13 black
yellow 20 white
white 25 red
ST 41 AMP 964825 - green AMP 964825 - blue
green 9 28
brown 13 9
green 17 black
yellow 18 green
white 25 1
yellow 25 23
ST 28 AMP-929650-2
yellow 9 yellow
green 10 green
brown 13 11
white 20 white
yellow 25 10
white 25 5
ST 9+15 AMP1-963553-1(24pin) 191972530B(28pin)
yellow 4 13
R-10k 9
green 10 7
white 10 2
brown 13 5
brown 13 9
brown 13 1
yellow+R 14 4
green 15 3
white 25 1
white 25 13
grey 25 17
ST 48
yellow 18 yellow
green 17 green
white 7 white
brown 13 brown
ST 27 TYCO-M1026-S502
yellow 10 11
green 9 9
brown 13 blue 1
white 25 14, 16
is right here?
twincam
28th October, 2013, 08:01 PM
it is possible do mercedes e211 2007 with clone digiprog? need hc12 adapter , but I not have in my set of cables...
With Digi you are doing only dashboard by obd it turn off synchro between EZS and dash.If You want to do ezs also You need to use some external programmer becouse there is no Hc 12 adapter in diggi set.
xyznia
28th October, 2013, 10:28 PM
obd no problem,dash+flash work perfect no need to rewrite ezs,if CDI engine after you will get DPF error and you need to do filter replacement with Launch or Star. but if you want to do everything ideal you need rewrite EZS and Gateway with motorola programmer ,service menu is possible with Digiprog but EZS better don't try:joyous: mileage stored also in battery module
thunderwinged
29th October, 2013, 03:55 PM
mercedes is problem many km stored in car :(
moto111
29th October, 2013, 10:35 PM
Where can i buy ugrade ? please pm
TULGEYWOODMAN
30th October, 2013, 12:11 AM
THEY ALL WANT ****IN JAM ON IT .... Free and 4.88 ... why not just ask for 4.92 for free ....
jam, marmite................the ******* lot................wallop.
michalez
30th October, 2013, 11:25 AM
in obdiigroup.com website (old nandtools.com) they write that for their clients there are free update from 4,82 to 4,85. I wrote to them and [11:03:59] www.OBDIIGROUP .COM: now, DIGIPROG 3 still no free update
[11:04:09] www.OBDIIGROUP .COM: you wait, maybe some time later, it can be updated for free. ;/
i bought from them and there was no usb ---> pc chip. sn 590c8f0e0000 so it cant be updated.
They sell now digi with 4,85...
CARPARTS
30th October, 2013, 01:12 PM
in obdiigroup.com website (old nandtools.com) they write that for their clients there are free update from 4,82 to 4,85. I wrote to them and [11:03:59] www.OBDIIGROUP (http://www.OBDIIGROUP) .COM: now, DIGIPROG 3 still no free update
[11:04:09] www.OBDIIGROUP (http://www.OBDIIGROUP) .COM: you wait, maybe some time later, it can be updated for free. ;/
i bought from them and there was no usb ---> pc chip. sn 590c8f0e0000 so it cant be updated.
They sell now digi with 4,85...
......that's again a reason why you should NEVER EVER trust a yellow men or woman !
More specific in the Shenzen district
TULGEYWOODMAN
30th October, 2013, 10:11 PM
mercedes is problem many km stored in car :(
fu**ing hell ,youre quick !
u.s
30th October, 2013, 11:18 PM
managed to get hold of a CAS2 unit from an E60 to have a play with.
made my own ST-CAS cable and did CAS module out of the car (made a backup first using red rosfar clone)
http://www.dailymotion.com/video/x16m90i_bmw-e60-cas2
EDIT: i did put a video up but the video is not showing up on my mobile devices???
link as follows http://www.dailymotion.com/video/x16m90i_bmw-e60-cas2
justy22
31st October, 2013, 04:50 PM
managed to get hold of a CAS2 unit from an E60 to have a play with.
made my own ST-CAS cable and did CAS module out of the car (made a backup first using red rosfar clone)
http://www.dailymotion.com/video/x16m90i_bmw-e60-cas2 Lets have a look at it
drpeter
1st November, 2013, 08:07 AM
managed to get hold of a CAS2 unit from an E60 to have a play with.
made my own ST-CAS cable and did CAS module out of the car (made a backup first using red rosfar clone)
http://www.dailymotion.com/video/x16m90i_bmw-e60-cas2
EDIT: i did put a video up but the video is not showing up on my mobile devices???
link as follows BMW E60 CAS2 - Video Dailymotion (http://www.dailymotion.com/video/x16m90i_bmw-e60-cas2) What's new? I did this almost 2 years ago with the digiprog clone. By the way you better choose cas plug by pressing ''X'' in the cas diag menu.
u.s
1st November, 2013, 11:01 AM
Sorry mate didn't mean to piss on your bonfire.
Nothing new, I was only reporting/confirming what I have tried that worked.
There was a use who posted screenshots of his CAS cable much earlier in the thread.
EDIT: sorry mate only just read your sig, after liking your post... Doh
drpeter
1st November, 2013, 12:03 PM
Sorry mate didn't mean to piss on your bonfire.
Nothing new, I was only reporting/confirming what I have tried that worked.
There was a use who posted screenshots of his CAS cable much earlier in the thread.
EDIT: sorry mate only just read your sig, after liking your post... Doh No problem, it was already discussed many times before, and about 50 % are ''unknown versions". Better try to read on dash connector if the cas version is recognized. Saves you even more time. You must have small fingers to remove the fuses though. I hope that the ''fuse'' thing is solved for CAS2 in the future, just like smelecom or enigma.
PremierD
1st November, 2013, 04:28 PM
Did the same job on E90 about two hours ago ... Diggy Rules ....lol
marcio1758
4th November, 2013, 01:18 PM
Digiprog 3 V4.85 Update Service (http://www.immokm.com/wholesale/digiprog-3-v485-update-service.html)
someone might be interested!
thunderwinged
4th November, 2013, 04:03 PM
someone know or make update to 4.85 in digiprog 590C0FE00000?
PremierD
4th November, 2013, 04:52 PM
Banned serial .. I think you have been informed of that already mate .. :)
Apolo29
4th November, 2013, 05:17 PM
Digiprog 3 V4.85 Update Service (http://www.immokm.com/wholesale/digiprog-3-v485-update-service.html)
someone might be interested!
I see 4.85 update, but the don?t say anything about 4.83 or 4.84, are they added?
PremierD
4th November, 2013, 05:19 PM
No mate ... they dont give you them .. they are extra ... :roflmao: ...........
digimile
6th November, 2013, 01:56 AM
hi digiprog 4.82 ......offcourse clone....please share experice with VW polo.....from 2007 to 2012.....or 13......thanks
vageric
6th November, 2013, 05:37 AM
hi digiprog 4.82 ......offcourse clone....please share experice with VW polo.....from 2007 to 2012.....or 13......thanks
read the complete thread 167 page
rust55
6th November, 2013, 05:52 AM
here will update your device.????? ???? ?? ??????? ?? Viktor (Cardiag) - ????????????? ?????? Oktja.ru (http://www.oktja.ru/forum/topic/70185-%D0%BF%D1%80%D0%B0%D0%B9%D1%81-%D0%BB%D0%B8%D1%81%D1%82-%D0%BD%D0%B0-%D0%BF%D1%80%D0%B8%D0%B1%D0%BE%D1%80%D1%8B-%D0%BE%D1%82-viktor-cardiag/)
Powered by vBulletin® Version 4.2.5 Copyright © 2025 vBulletin Solutions Inc. All rights reserved.