Digiprog 3 clone questions and answers

[rukartinatv]

you do bmw e60 by obd or .....

by obd? how you can do dash by obd?
Thank you

[wiseman]

He is asking if the CAS went by Obd

[Meat-Head]

i only cant get a grip on golf mk 3 i think some problem in cable, if someone have schematic for cable pls upload.

the cable is not same as TU i see difference in power cable TU have 2 massa and 2 plus cables my digiprog have only 1 plus and 1 massa.
put 2 extra cabels but same result.




1) Gulf has TWO earths, one for the warnging lamp electronics, one for
the gauges

2) will have two lives, B+ and Ignition.

OFF TOPIC - BUT RELEVENT:-

*THINK* Use search botton member Z786 had a passat thrrad
somebody uploaded the pin data, you can use some of that data
as a reference it is also - MK III info on here - some where.

[dimet]

Can someone tell me whether the trust this company Digiprog III Odometer Programmer - $478.30 : go car diagnostic , scanner , car , auto scanner, car diagnose, diagnostic tools (http://www.gocardiag.com/index.php?main_page=product_info&cPath=72&products_id=621)

[54321]

Can someone tell me whether the trust this company Digiprog III Odometer Programmer - $478.30 : go car diagnostic , scanner , car , auto scanner, car diagnose, diagnostic tools (http://www.gocardiag.com/index.php?main_page=product_info&cPath=72&products_id=621)
I've used them a few times and everything has been ok

[chrismoore02]

Why waste your time with dp3 on mk3 golf just use upa and brain.exe would prob be quicker too

[honingkoning]

Why waste your time with dp3 on mk3 golf just use upa and brain.exe would prob be quicker too

mate shall we both make a movie, through dash plug golf 3 takes about 2 min.

I am sire in 2 minutes you are not able to open dash.

Regards Adam

[honingkoning]

Bmw e60 its m35080v? how you say ok if dp3 dont support to eraze this chip m35080v?
Thank You

I did not say i erased the eep, i was able to read good milleage and program to a new chip.

Since i screwed up some dmps in the past i never reprogram a 35080, i always replace them and when all ok i use the old eep for next job, same as bsi cars.

Regards Adam.

[Meat-Head]

off topic:;-

gulf clocks has a programming port.

on topic;

justy you reprog yours yet?

[honingkoning]

off topic:;-

gulf clocks has a programming port.

on topic;

justy you reprog yours yet?

I finished mine @ 23:06 like i said 2 min.

[chrismoore02]

You can do them in circuit with an eeprom clip in about 2mins you only have to unclip the cover off the back of the clocks - each to their own :D

[z786]

chris are u sure u have done one of these

[smokey08]

IIRC the chip is under the screen that has to be desoldered. Easy with TU on the test points on the rear.

[Meat-Head]

we seem to be going off topic.

next person to mention gulf 3, make it a link to another thread!

[chrismoore02]

Off topic - we are obviously talking about different mk3 dashes as the ones I have done were TRW dashes and via EPROM clip

On topic - I've heard some people have had issues with the touch screen has anyone here had these issues

[z786]

we seem to be going off topic.

next person to mention gulf 3, make it a link to another thread!

the DKCSO is getting pissed off

(Digital Kaos Community Support Officer)

imagine if u was a mod, we'd all be banned lol

[batandball]

Hi
Any one had any luck with the dash plug on a BMW 3 / 5
Noticed on my lead when i stipped it down the tracks have been cut through with a knife

[smartymarti]

Hi
Any one had any luck with the dash plug on a BMW 3 / 5
Noticed on my lead when i stipped it down the tracks have been cut through with a knife


thats quality for ya

[batandball]

I dont remember asking for quality control

[wurz]

Quality is important but all in all these digiprogs seem to be very close to the original, even down to the sound when using the touch screen. I think we all accept that you get what you pay for and take chances on these things from time to time. I think as long as you do enough testing with the machine before letting it loose on a 2012 5 series then you'll know it's capabilities and limits.

[batandball]

Most of the people wot slag clones will a got a clone in there stash

as we all know
unless
rosfar
universal tacho
MB Star
OPcom
vag
autoboss
upa
clones
and so on, dont count

[Meat-Head]

thats quality for ya

not 100% sure but posssable same board for a ?? and modifited for bmw, or was misrake in producrtion'

upload clear photos

[skens]

hi
vw golf 6 ,2011 , VDO tacho obd 2 min !!ok!!
regards

[almeida]

Hello
I try this tool digiprog clone at 2 audi a4 2009
Both times read fine and after 10m not change.
I try with vag k can 2.0 ( blue toy ) and job done after few seconds.
Some one have the same?
Cheers

[antibisic]

Hello
I try this tool digiprog clone at 2 audi a4 2009
Both times read fine and after 10m not change.
I try with vag k can 2.0 ( blue toy ) and job done after few seconds.
Some one have the same?
Cheers

I don,t have the digiprog but it look,s like wrong version selected like example when you select by passat before 2006 and after 2006 it read good but can not change

[enigmauk]

If it read fine it should Have worked... try another year as listed above. What error or message did your machine give?

[wiseman]

Dash fuses may need to come, then it may work, some Audi a8's need this

[abdallah]

for the audi a4 2008 demand 1 min for reading and 30min for writing
a4 2008 30min job work ok by obd

[almeida]

Thanks
Better next time

[enigmauk]

Dash fuses may need to come, then it may work, some Audi a8's need this

Even some A6's need fuse out with Enigma... so could be the case... take it out for 20 seconds and then back in next time.

I did a Audi A8 with Digiprog clone by obd the other day... worked perfect... it was 2008.

[wiseman]

Even some A6's need fuse out with Enigma... so could be the case... take it out for 20 seconds and then back in next time.

I did a Audi A8 with Digiprog clone by obd the other day... worked perfect... it was 2008.

How long was reading and writing?

A friend of mine has a Digiprog and tried it on a polo RB8 Earlier worked fine, went to try his 2010 VW t5 van and it wont read now, but it did before. This van runs UDS not CAN, any ideas?

[enigmauk]

It was only a few minutes max

[batandball]

How long was reading and writing?

A friend of mine has a Digiprog and tried it on a polo RB8 Earlier worked fine, went to try his 2010 VW t5 van and it wont read now, but it did before. This van runs UDS not CAN, any ideas?

Tell your mate to look at post 95

[wiseman]

Tell your mate to look at post 95

I forgot about this issue, I bought a plug kit aswell but havent used it.

[Shaheenem]

Tested:
Vw polo 6r 2011 obd OK
VW lupo obd OK

Then I try vw golf 6 2010 unit switches off
Also try 2001 audi a4 and unit switches off

Anyone have similar problem with digiprog?

[nikabbi]

i have enigma, this digiprog clone which functions has more than enigma? for example make ajustment in service history on zgw? thank

[enigmauk]

This is not a replacement to enigma it is a clone tool not a pro tool.

[nikabbi]

i know, i have original enigma, but not have function for service adap'tation in zgw, if this clone can do it i buy...

[smartymarti]

Think you might have overlooked the support issue , at least with pro tool you have some assistance even if limited some is better than none

[enigmauk]

You can edit Assyst using digiprog but it isnt very good... i would edit it using AVDI or other tool...

[Meat-Head]

Think you might have overlooked the support issue , at least with pro tool you have some assistance even if limited some is better than none

OFF TOPIC:- BUT RELVENT-:

Our Swiss Army Pen Knife with OBD Scanner is a GENUINE product, we
pay ?650+VAT per year to keep it on line, unit cost new ?7000, does have a LOT of extra blades.

We had a problem, rung them up, would have better use of a phone call ringing the parts people and asking the *HOT* bird out.

Another time we had a problem activating the software - instead of just saying, oh you need to XYZ, the bloke ended up talking to some bloke called Sven in Sveden about it, who said, do XYZ

It got sent back more than once, second time it didn't need to be sent back - at our expense - but useless co*oont didn't say anything.

Would like to point out although then fixed, a DK member posted the soltion for FREE.

HTH

Meat.

[nikabbi]

You can edit Assyst using digiprog but it isnt very good... i would edit it using AVDI or other tool...
why not is very good in zgw? what other tool economic you know for this function? i know and have avdi-but not active mercedes functions-

[skens]

hi
Vw passat B6 -2008 obd OK 1min
regards

[honingkoning]

vw lupo 2002 with rb 4 dash not ok
get message "unknown version rb4"

fiat punto 2000 read good milleage when programming is finished it says verify new milleage but milleage still the same.
btw how is it possible that fiat stilo does not have a obd option.

any idea.

[PremierD]

Coz its a FIAT mate ... Fck It Away Today .... lol

[blackpirate]

stupid question:
does digi3 support edc15/16 mileage adjusting on VAG???

[PremierD]

Stoopid answer .... Yes ...lol

[mislav88]

Coz its a FIAT mate ... Fck It Away Today .... lol

...or Fix It Again Tomorrow

[blackpirate]

Stoopid answer .... Yes ...lol

anybody tested??:)

[kisslorand]

Tested on Audi A4 EDC16, not working. Tested on VW Passat EDC16, working.

[z786]

some edc16 are impossible, they have to be done manually

[motorsport]

some edc16 are impossible, they have to be done manually
yes like first audi A3 8P year 2003

[antibisic]

stupid question:
does digi3 support edc15/16 mileage adjusting on VAG???

I don,t think so because my friend has original digiprog but use some tool from codecard to do edc15

[zecas]

I don,t think so because my friend has original digiprog but use some tool from codecard to do edc15

unfortunally 15 usd k+can v1.4 does km in edc15

[batandball]

It does the ecu on golf 5 plus auto gearbox

[antibisic]

unfortunally 15 usd k+can v1.4 does km in edc15

Question was about digiprog not about k+can

[batandball]

i was on about digiprog

[tomuch]

...or Fix It Again Tomorrow
or in German FIAT FEHLER IN ALLEN TEILEN
ERROR IN ALL PARTS

[dvdegrt]

Got machine this week tested litle mercedes w204 obd ok
Golf4 vdo ok edc 15 not work comunication error made it smelecom no trouble then friend tested audi a6 ok edc 16
not work tried ford 2006 912 4 wires ok
Tried 93c46 mazda ok trouble tried turn chip wrong owerheats smelecom never also digimaster beter for that
anyway if put inside corect work ok .
Anyway for now can say for 500usd is ok can work on cars have trouble other machine but beter save all data first before use digiprog cause didnt see any save option inside

[honingkoning]

Got machine this week tested litle mercedes w204 obd ok
Golf4 vdo ok edc 15 not work comunication error made it smelecom no trouble then friend tested audi a6 ok edc 16
not work tried ford 2006 912 4 wires ok
Tried 93c46 mazda ok trouble tried turn chip wrong owerheats smelecom never also digimaster beter for that
anyway if put inside corect work ok .
Anyway for now can say for 500usd is ok can work on cars have trouble other machine but beter save all data first before use digiprog cause didnt see any save option inside

Tell u did w204 all by diagnose all units or only dash and pls explain, cause the pdf i have are old and i am not shure how to do this car.

Regards Adam.

[vageric]

you can do only dash.
rest of car is on 1 milion mileage.
that is if car isnt dead after correction. (see it happend)

[dvdegrt]

Hm me only did dash it was friend car only tested but only
first tried put mileage like 128000 car had 127000 then when
sucesesfuly made tried 123000 then again 118000 then checked with star mileage on ezs 118000 asyst also was ok moved last service back but maybe moved back with some other machine before.

[batandball]

you can do only dash.
rest of car is on 1 milion mileage.
that is if car isnt dead after correction. (see it happend)

Can you tell me someone that's f-cked av Merc 204 212 up with Digiprog clone,
Start car and do diag, I think if you do with a DP3 diag prog 3 you get same results but about ?6000 cheaper :banghead:

[vageric]

for me it does not matter who do what with what machine.
i only tell you that i see it happend when mine friend tried the digiprog clone on a w204 and on a w212.and this was before the clone came official on the market.
both car was dead after. but for him it does not matter because he have also elprosys, avdi and enigma for use and he is lets say a mercedes specialist. ps:before he have used the digiprog clone he have make backup with other tools.

[PremierD]

PS .. Elprosys is even killing the Mercs mate ... lol.. but keep it to yourself .. don't want to start a riot lol

[smartymarti]

Touch wood never had an issue doing any mercs with dp3 up to date

[batandball]

for me it does not matter who do what with what machine.
i only tell you that i see it happend when mine friend tried the digiprog clone on a w204 and on a w212.and this was before the clone came official on the market.
both car was dead after. but for him it does not matter because he have also elprosys, avdi and enigma for use and he is lets say a mercedes specialist. ps:before he have used the digiprog clone he have make backup with other tools.

Your mate must be a very brave or stupid person to try 2 different Merc with a machine that's f-cked one up when he as, as you say a machines that does them perfectly ok. I ant read about any body on this topic saying its messed a Merc or any other car yet that's been the machines fault. This machine will take a copy of eeproms and micros. The only problem I've had sometimes is it won't take a copy of some eeproms in circuit
PS
What tool did he take a back up of the Merc key box with ?

[rukartinatv]

Can you tell me someone that's f-cked av Merc 204 212 up with Digiprog clone,
Start car and do diag, I think if you do with a DP3 diag prog 3 you get same results but about ?6000 cheaper :banghead:

no with diagprog you get diferent resolt.
Diagprog put in dash and ezs thesame km!!!

Digiprog put 1 milion in ezs.

[markony79]

My friend do yesterday w212 with digiprog clone(500$)
I can not belive it.....uuuuffff

[honingkoning]

My friend do yesterday w212 with digiprog clone(500$)
I can not belive it.....uuuuffff

Small update today tested on a 2001 corsa and all ok, no special car but for some people maybe Nice to know.
Also tested on a e36 sw 14 would not go through diagnostic port with none of the tools i have.
So removed dash and direct to dash 20 sec job with good old TU.

Regards Adam.

[batandball]

If you watch DP3 (Diagprog3) doing a E / C Class Merc the clocks go upto 999999 miles then goes to the mileage you put in

[solar]

i try old 912 bsi 307 with this tool and now bsi dead(wipers,light on when you turn on ignition+cant connect pp2000).....try FFFFF no work bsi dead.maybe bad look,maybe tool....did more then 20 cars(mainly by eeproms japaneese makes with no problem)....i hate this tool because he cant save original file...

[sparkz02]

diagprog, does go to 999999 but when checked with star it inputs the required km, touch wood, I've done over 50 mercs with dp3 & haven't messed one up. - dont get it wrong for the price digiprog is good but come on, don't compare to diagprog or something of that level its seriously not smart.. diagprog for mercs has more software supported versions then AVDI,

The 50 +mercs ive done alone paid for my dp3, the rest was for free.

[batandball]

i try old 912 bsi 307 with this tool and now bsi dead(wipers,light on when you turn on ignition+cant connect pp2000).....try FFFFF no work bsi dead.maybe bad look,maybe tool....did more then 20 cars(mainly by eeproms japaneese makes with no problem)....i hate this tool because he cant save original file...

User error
You can save original data with this tool. So I put that down to you
not using it right.
Picture attached
I've done 912 peuget ECU with Digiprog

EEPROM
Set type
912
Read
Save

[batandball]

diagprog, does go to 999999 but when checked with star it inputs the required km, touch wood, I've done over 50 mercs with dp3 & haven't messed one up. - dont get it wrong for the price digiprog is good but come on, don't compare to diagprog or something of that level its seriously not smart.. diagprog for mercs has more software supported versions then AVDI,

The 50 +mercs ive done alone paid for my dp3, the rest was for free.

Sparkz02
I'm not comparing one machine with another, I know Merc 204 / 212 works with this, some one said in a earlier post about 204 / 212 been messed up by his friend with this tool, BUT a user of Digiprog as not mentioned it messing one up yet ?. The member that mentioned not been able to save original data obviously as,nt had a good look round this tool, can't believe he changed data without saving original 912 data that's asking for trouble, any machine can put data error in a dash or bsi.
Lots of people like to slag this clone cos they paid thousands for original tool but that don't make you good at clocker. Most of the things that don't work on Digiprog clone is down to crap leads

[dvdegrt]

Agree with that need save first not once me reather save it 2-3 times this tool is good for experienced users with some other tools if this only tool me wouldnt do anything with it.
And also sugest keep it away from cas modules and ezs.
Use rosfar r270 and etl for fix is still something go wrong
anyway think obd should all work fine.

[solar]

batandball,
thanks,somehow i not see save function before:)yes,was user error(because not save),and bsi error because she dead(not because bad read-write,just dead......replace with another one,try tool again,works 100%.

[honingkoning]

batandball,
thanks,somehow i not see save function before:)yes,was user error(because not save),and bsi error because she dead(not because bad read-write,just dead......replace with another one,try tool again,works 100%.

Bad luck, shit happens but good clone ***128515;.

Regards Adam.

[olegario]

I saw few times "Voltage too high" on the screen after boot and screen freezing. With own power adapter and another one. Is it reason of worries? Must I change some power stabilizers inside the box? Saw Pcb and solderings looks OK.

[dvdegrt]

Me also get voltage to high sometimes but all work normal
tried clio mm hc 08 today for test get error or sometimes machine freeze tried lift green cable aswell also not work
but this trouble my other machine aswell carprog normall
works but that also work cluster diagnosis.

[koziolek]

so over all is this machine worth $400?

[batandball]

so over all is this machine worth $400?

I think your on the wrong forum, for jokes go on sickipedia.
I've spent more on my iPhone

I would post link on here but PremierD might give me a bollocking

[PremierD]

But is it a clone ... or original ...... ? lol

[batandball]

But is it a clone ... or original ...... ? lol

Original
I got it when I was on holiday in Thailand, when I was with my new good looking Thai bride !!!!!!

Are we on about bride or phone ?????

[PremierD]

I would imagine it was the phone mate .. as you forgot to tell me you were married ...

[olegario]

Ibiza 2007 dash MM with 912h256 inside, can't do by OBD .

[obdiidiag1986]

which cable use for 93CXX chip programming ? could attached the picture?

[antibisic]

Anybody tryed VW T5 2007-8 year tacho and edc16 is it works?Thanks

[ALEXEI]

Anybody tryed VW T5 2007-8 year tacho and edc16 is it works?Thanks

this ecu must be done manualy like Tuareg same engine.
Ive tried with Elprosys, Enigma, AVDI. None can do it via obd.

[antibisic]

this ecu must be done manualy like Tuareg same engine.
Ive tried with Elprosys, Enigma, AVDI. None can do it via obd.

I have read somewhere in this thread that guy done both ecu and dash with digiprog 3

[batandball]

Anybody tryed VW T5 2007-8 year tacho and edc16 is it works?Thanks

try it the golf 5 ecu works diag

[koyot]

I read and write to obd

VW T5 2007-8 year tacho and edc16

[PremierD]

"Ive tried with Elprosys, Enigma, AVDI. None can do it via obd."

Then buy a shitty clone ... lol

[ALEXEI]

"Ive tried with Elprosys, Enigma, AVDI. None can do it via obd."

Then buy a shitty clone ... lol

I have also the shity clone but since Ive got it never met T5.

[dimet]

Can I do a mileage of golf 5 visteon 2005 with digiprog3?

[TULGEYWOODMAN]

PS .. Elprosys is even killing the Mercs mate ... lol.. but keep it to yourself .. don't want to start a riot lol

Well I do at least 6 a week, total to date over 100, never ever ever ever had a problem with dp3.
Abrites did put 9999999 in without warning ,when it came across late model, dp3 on the other hand gave you a warning. Abrites now give prior warning if it cant do it.

Everyone must do ther own thing, but my thoughts are if I am making good money why not buy proper equipment? Why take a chance?

The other interesting point is........What about the rest of the mileage locations? I dont think the digithingy will do those!

I

[PremierD]

I can assure you it was killing them Eric .. and we seem to be slipping back to the old routine ... Spend a fortune and it will always be correct ...

[TULGEYWOODMAN]

Well it depends on what volume you are doing and who for?

I did say "my thoughts are"

I will never condone the use of equipment costing ?300 on a car costing ?60k.

Where is the sense in that?

My point was.I never killed any.

Maybe the operator was at fault?
Maybe not keeping voltage stable with the use of jumper leads and a running donor car.

Clones are ok if you have the money and resources to repair the breakage if it occurs. But one must assume that the reason to buy a clone was due to lack of funds in the first place.

as I said, everyone must do there own thing.

[PremierD]

So 5 grand... .. 60k ... thats ok ..? lol You said it Eric you just do your own thing and leave the chancers to their own ends .. to save up and become as successful as you .. ..

[drpeter]

I never damaged a Cas Ezs or Benz in 7 years and I only use clones for this. You can not speak of luck anymore :-)

Verstuurd van mijn GT-N7000 met Tapatalk

[TULGEYWOODMAN]

I never damaged a Cas Ezs or Benz in 7 years and I only use clones for this. You can not speak of luck anymore :-)

Verstuurd van mijn GT-N7000 met Tapatalk

Who speaks of luck?

[rukartinatv]

some one try bmw E65 2008 with dashplug?
or any cas2 dashplug?
Its work for you.

[PremierD]

Saw one done OBD ... Cas 3 though

[rukartinatv]

cas3 i know what about cas2?

[PremierD]

You getting Unknown Version ?
Someone got that yesterday .. same used to happen with TU ...

[TULGEYWOODMAN]

When doing cas 3 with DP3. I try first without key,then if no luck insert key , if still no go, then ign on.

I try switching lights on and off at same time.
Maybe try this method with digiprog?

[rukartinatv]

with dp3 cas 3+ work try obd with out any problem.
cas2 with dp3 dont work i try like 11 cars no luck
e65 with dp3 obd dont work.
that why i ask if someone did e65 cas2 try dashplug with digiprog???

[TULGEYWOODMAN]

with dp3 cas 3+ work try obd with out any problem.
cas2 with dp3 dont work i try like 11 cars no luck
e65 with dp3 obd dont work.
that why i ask if someone did e65 cas2 try dashplug with digiprog???

With respect, you didnt ask if someone did e65 cas2!



quote #602
"some one try bmw E65 2008 with dashplug?"

[wiseman]

head lights on and radio can stop a Cas from sleeping.

[javyb]

So does cas 3+ by OBD work on digiprog 3?

[ALEXEI]

just tried today VECAM module from Freelander 2 2008.
wrong calculation. dont waste your time with it.
dash went good.

[smartymarti]

As wiseman said turn lights to stop cas from going to sleep and turn the radio on, was always told to do this with enigma on cas2

[PremierD]

So does cas 3+ by OBD work on digiprog 3?


Read a few posts .. and guess mate .....

[abdallah]

is that digiprog3 change km for golf 6 2012 by obd ;odometer with color screen ?
thanks

[ALEXEI]

is that digiprog3 change km for golf 6 2012 by obd ;odometer with color screen ?
thanks

and what else do you want more ?
maybe a virgin to polish your tool

[batandball]

and what else do you want more ?
maybe a virgin to polish your tool


I would say it depends on the tool that wants polishing ;)

[batandball]

is that digiprog3 change km for golf 6 2012 by obd ;odometer with color screen ?
thanks

Normally when you try with OBD, machine should search for dash type ie: serial numbers in dash before they continue. Try the latest version of golf 6 OBD

[skens]

hi
jeep cherokie 2004 908as60 plug 42 not work
regards

[Shmortz]

is that tool working by dump, I need to calc km and checksum on golf5 visteon dash with error on km display, dump is in that thread: http://www.digital-kaos.co.uk/forums/f174/another-golf5-visteon-error-299892/

[honingkoning]

is that tool working by dump, I need to calc km and checksum on golf5 visteon dash with error on km display, dump is in that thread: http://www.digital-kaos.co.uk/forums/f174/another-golf5-visteon-error-299892/

My friend TU can do this dash by eep and by diagnostic.

I dont know if this tool can fix your problem.

[dimet]

More tested cars with this tool please.

[dimet]

I made a file from this thread for digiprog3 what works and what does not work.

[blackpirate]

I made a file from this thread for digiprog3 what works and what does not work.
thank you very much for your time collection all this info!!

[ALEXEI]

I made a file from this thread for digiprog3 what works and what does not work.

I did A klasse obd OK
Meriva and Corsa C obd OK.

[diga1]

astra 1998 vdo obd not vorking. device freezes.
old taho universal vorks like a charm

[dimet]

astra 1998 vdo obd not vorking. device freezes.
old taho universal vorks like a charm

You do not need for that car digiprog3. It can be solved with a op-com like a charm.

[dimet]

I did A klasse obd OK
Meriva and Corsa C obd OK.

What year?
Please more information.

[ALEXEI]

What year?
Please more information.

A klasse 2001
Corsa C 2003
Meriva 2004
obd all ok

[abdallah]

What is used the function assyst diag in mercedes ?
thanks

[TULGEYWOODMAN]

What is used the function assyst diag in mercedes ?
thanks

Its method of editing the service assyst records.

[angelcom]

ford ranger 68hc05 ok

[angelcom]

hi
jeep cherokie 2004 908as60 plug 42 not work
regards

dont work at all, I try with two models of boards

[wadim21]

Megan 3 ABS, work only with ESP unit ,without ESP not work

[antibisic]

Megan 3 ABS, work only with ESP unit ,without ESP not work

Is it OBD or not?

[wadim21]

Is it OBD or not?
not.eprom.

[justy22]

dont work at all, I try with two models of boards

TU can do this via OBD

[TULGEYWOODMAN]

TU can do this via OBD

I think you have been drinking too much British Rail Tea

[abdallah]

is there anyone who try w212 and w204 by obd?
is there anyone who has cable diagram for digiprog3 ?
thanks

[technobox]

i try mate working w212 and w204 obd dash and ezs

[88diablo]

is there anyone who try w212 and w204 by obd?
is there anyone who has cable diagram for digiprog3 ?
thanks

Here attached.

[abdallah]

thanks technobox
w204 w212 working by obd ? no need remove ezs?
thanks

[abdallah]

thanks 88diablo
i have this schema but it s no clear for repar some cable for exemple cable number 42 not working
do have another schema?
thanks

[88diablo]

These are photos of mine if that helps.

[skens]

hi
mercedes w 204 2009 year
W204 (C) EZS - DIAG ok , 2 min
W204 (C) - TACHO - DIAG ok, 2 min
W204 (C) - ASSYST - DIAG ok, 15 min

[abdallah]

hello
i need to adjust odometer for w212 by obd : dash+ezs
in the menu of digiprog 3 i have:
1 tacho diag
2 tacho 24c128
3 ezs
4 assyst diag
5 assyst 24c128
6 clr error
what program i use to adjust the car by obd ?
thanks

[yeager]

1 tacho diag
2 ezs
3 assyst diag
4 clr error

[rukartinatv]

hi
mercedes w 204 2009 year
W204 (C) EZS - DIAG ok , 2 min
W204 (C) - TACHO - DIAG ok, 2 min
W204 (C) - ASSYST - DIAG ok, 15 min
What you mean W204 (C) - TACHO - DIAG ok?????
If you do EZS OBD its change the km in ezs and the tacho!!!!!

[rukartinatv]

1 tacho diag
2 ezs
3 assyst diag
4 clr error

You cant do S class by obd2
If you press EZS its will ask you to install can filter.
Can some one confirm if you did W221 by obd.
Thank You

[PremierD]

"hello
i need to adjust odometer for w212 by obd : dash+ezs
in the menu of digiprog 3 i have:
1 tacho diag
2 tacho 24c128
3 ezs
4 assyst diag
5 assyst 24c128
6 clr error
what program i use to adjust the car by obd ?
thanks"

I think if you read mate .. he was asking about a W212...

Which most certainly can be done .. colour screen as well .. choose EZS .. enter kms required .. it does the rest for you .. takes all of about 1 minuite .. then do assyst .. takes about 15 mins .

[diagnoza_auto2000]

And how many km you will have then in EZS if you check with Xentry?

[kisslorand]

You'll have 1.600.000 Km

[cokolo]

Or maybe like these :wink:


ps. With AVDI :wavey:

[cokolo]

Or maybe with your Digiprog 3 chines interface (450usd) :afraid:, you can do odo in ECU (w212,w204,x204,w197,w207,w218) lollollollol

[abdallah]

1 tacho diag
2 ezs
3 assyst diag
4 clr error
hello yeager
are sure for the w212:
1 i use :tacho diag and i enter the new km for exemple 60000 km ?
2 i use :ezs and i enter the same value km in tacho diag :60000 km ?
3 i use assyst diag ?
4 i use clear error ?
thanks

[motorsport]

Or maybe with your Digiprog 3 chines interface (450usd) :afraid:, you can do odo in ECU (w212,w204,x204,w197,w207,w218) lollollollol
Tested on W212 ecu year 2010 commender not read

[diagnoza_auto2000]

You'll have 1.600.000 Km

And you think that is good?

[javyb]

And you think that is good?

Well the mighty Diagprog 3 by elprosys puts 1.600.000km in the EZS and Diagprog 3 is supposed to be a state of the art machine!!!

[z786]

they all put 1.6 million but a few disguise it

[diagnoza_auto2000]

AVDI will make real value

[PremierD]

"Digiprog 3 clone questions and answers"...

Where does it metion AVDI.. in the thread title mate .. I can't seem to find it .........?

[z786]

AVDI will make real value

no, not in ezs

avdi will flash gateway to show correct miles everywhere but not actual km in ezs

[TULGEYWOODMAN]

Well the mighty Diagprog 3 by elprosys puts 1.600.000km in the EZS and Diagprog 3 is supposed to be a state of the art machine!!!

If you read with star after it wont show that!

[TULGEYWOODMAN]

no, not in ezs

avdi will flash gateway to show correct miles everywhere but not actual km in ezs

I assumed that everyone knew that its not possible to write to NEC in EZS and all machines are flashing Motorola in SAM

It doesnt matter what tool you use,or where its made or what it cost!

If it does the job you ask of it and doesnt fkcu the car then thats ok , yes?

We are talking about dash display and assyst yep?

All the other kms locations are only for people who are serious about doing a proper job!

[javyb]

If you read with star after it wont show that!

So if we correct with digy wigy clone and read with star it will show 1.600.000km ?

[TULGEYWOODMAN]

So if we correct with digy wigy clone and read with star it will show 1.600.000km ?

Dont know about didgy widgy clone,
But if you correct it with DP3 or AVDI it wont!




ps I thought it writes 999,999 kms not miles!

Could it really write over 1 million in it?

[batandball]

So if we correct with digy wigy clone and read with star it will show 1.600.000km ?

Jav by the time you get your Digiprog it will have traveled that many miles lol

[javyb]

Jav by the time you get your Digiprog it will have traveled that many miles lol

Tell me about it worse than snail mail :giveup:

[TULGEYWOODMAN]

Jav by the time you get your Digiprog it will have traveled that many miles lol

the avatar is reaaaaaallllllllllllly good.

[justy22]

I think you have been drinking too much British Rail Tea

I've done a few Cherokees via obd with TU , the early pdf's were superceded , I have latest TU pdf's

[TULGEYWOODMAN]

I've done a few Cherokees via obd with TU , the early pdf's were superceded , I have latest TU pdf's

my apologies, I see you where looking at the Cherokee post.


TIP..... when trying to do jeeps & Chryslers obd with TU, if they wont go, then try jumper leads to running donor car
[just up your street]

[javyb]

I've done a few Cherokees via obd with TU , the early pdf's were superceded , I have latest TU pdf's

What year Cherokees have I managed to do via OBD with TU

[TULGEYWOODMAN]

What year Cherokees have I managed to do via OBD with TU

Well if you dont know .

How would we know!


:heeeelllllooooo:

[justy22]

my apologies, I see you where looking at the Cherokee post.


TIP..... when trying to do jeeps & Chryslers obd with TU, if they wont go, then try jumper leads to running donor car
[just up your street]

Even better tip if they don't work with ignition on then do it with ignition off , tam told me this one and works a treat

[javyb]

Even better tip if they don't work with ignition on then do it with ignition off , tam told me this one and works a treat

What year Cherokees have u managed to do upto by TU, Justy22

[justy22]

What year Cherokees have u managed to do upto by TU, Justy22

03 and 04 models done grandbcherokee and jeepncherokee both by obd

[javyb]

03 and 04 models done grandbcherokee and jeepncherokee both by obd

Which OBD connector u use the one with double ends for SRI cable 17 or dongle cable 33 thanks

[justy22]

Which OBD connector u use the one with double ends for SRI cable 17 or dongle cable 33 thanks

I think it was 33 but will upload the latest PDF later, also never ever switch ignition with cable connected or it will fry

[TULGEYWOODMAN]

I think it was 33 but will upload the latest PDF later, also never ever switch ignition with cable connected or it will fry

That rule applies to all cars with TU, in fact always switch ign on before plugging in any obd device

[Meat-Head]

That rule applies to all cars with TU, in fact always switch ign on before plugging in any obd device

RUMOR

toyota avensis pin ?? of diagnostic socket has pulse from coil to it - frys struff search autel

ON TOPIC :-

correct me if i'm wrong, did iii sodding phone see this does airbag reset and immo stuff?

O

if i'm wrong - what simular devise was it?

JUSTY, mate is the leads same quality as the carprog? meaning flexable not solid as a rock?

thanks

[spiria]

Hello.

Who have new pdf for Digiprog? Send me pls.

[almeida]

Hello
Anyone try with audi A3 from 2008
Cheers

[abdallah]

"hello
i need to adjust odometer for w212 by obd : dash+ezs
in the menu of digiprog 3 i have:
1 tacho diag
2 tacho 24c128
3 ezs
4 assyst diag
5 assyst 24c128
6 clr error
what program i use to adjust the car by obd ?
thanks"

[javyb]

"hello
i need to adjust odometer for w212 by obd : dash+ezs
in the menu of digiprog 3 i have:
1 tacho diag
2 tacho 24c128
3 ezs
4 assyst diag
5 assyst 24c128
6 clr error
what program i use to adjust the car by obd ?
thanks"

You have already asked this question and been given an answer!

[batandball]

"hello
i need to adjust odometer for w212 by obd : dash+ezs
in the menu of digiprog 3 i have:
1 tacho diag
2 tacho 24c128
3 ezs
4 assyst diag
5 assyst 24c128
6 clr error
what program i use to adjust the car by obd ?
thanks"

EZS then assyst
I had one last week that put the engine management light on after error clear, just use different machine to clear DTC,s code was something about DPF blocked

[wadim21]

FIAT PUNTO 2008 OBD not work
FIAT BRAVA 2008 OBD work

[TULGEYWOODMAN]

EZS then assyst
I had one last week that put the engine management light on after error clear, just use different machine to clear DTC,s code was something about DPF blocked

kms in dpf not match kms in odometer

[batandball]

kms in dpf not match kms in odometer

It happened when I used error clear, only one its done it on

[skens]

hi
GOLF 5 2008 kombiistrument 3HL , OBD -OK 1min
GOLF 5 2008 ECU DIAG R4 1,9L EDC 000SG OBD-ok 10min
regards

[wadim21]

W211 ZGW not work

[TULGEYWOODMAN]

It happened when I used error clear, only one its done it on

nothing to do with your machine, probably something different on that car?


done 2x 2012 w212 250 estates this week , one put light on, one didnt.

[wiseman]

Did you get the light to stay off eventually ?

[batandball]

Did you get the light to stay off eventually ?

Yes just used Autoboss
Like Tulgeywoodman said probably nothing to do with machine, I've done plenty and that was first

[wadim21]

insignia 2009 OBD not work (access denied) .tried 2 cars

[binken]

Has anyone test digiprog clon on Audi a4 2011 , Works or not


Skickat fr?n min GT-I9300 via Tapatalk 2

[saadoun]

"hello
i need to adjust odometer for w211 by obd : dash+ezs
it is possible or no ?
if possible what programme i use for this car
thinks

[batandball]

"hello
i need to adjust odometer for w211 by obd : dash+ezs
it is possible or no ?
if possible what programme i use for this car
thinks

Some 211 go by OBD but it only flashes the dash doesn't touch the ezs
Same as doing it through dash plug

[honingkoning]

Guys Laguna 2005 with 9s12 all ok through 4 wires

Regards Adam.

[enigmauk]

Some 211 go by OBD but it only flashes the dash doesn't touch the ezs
Same as doing it through dash plug

I tried one today (first with enigma) using OBD... it read the old mileage fine but when I went to program the new mileage it lost communication and wouldn't connect I even let the car sit for 15 minutes but no luck had to remove speedometer and do via cluster plug in the end.... ive not had a single w203 or w211 go via obd

[TULGEYWOODMAN]

I tried one today (first with enigma) using OBD... it read the old mileage fine but when I went to program the new mileage it lost communication and wouldn't connect I even let the car sit for 15 minutes but no luck had to remove speedometer and do via cluster plug in the end.... ive not had a single w203 or w211 go via obd

Why would you want a 211 or 203 to go obd?
During your 15min wait. I could have removed the ezs , done the miles, took the cluster out and done it from the back of the dash.............


bat nball..."Some 211 go by OBD but it only flashes the dash doesn't touch the ezs
Same as doing it through dash plug" .
Well why would it touch the ezs? [if it where to flash the dash, thats the point , to stop comms with ezs!

[batandball]

Why would you want a 211 or 203 to go obd?
During your 15min wait. I could have removed the ezs , done the miles, took the cluster out and done it from the back of the dash.............


bat nball..."Some 211 go by OBD but it only flashes the dash doesn't touch the ezs
Same as doing it through dash plug" .
Well why would it touch the ezs? [if it where to flash the dash, thats the point , to stop comms with ezs!


post 695 someone asking a question

[drpeter]

Why would you want a 211 or 203 to go obd?
During your 15min wait. I could have removed the ezs , done the miles, took the cluster out and done it from the back of the dash.............


bat nball..."Some 211 go by OBD but it only flashes the dash doesn't touch the ezs
Same as doing it through dash plug" .
Well why would it touch the ezs? [if it where to flash the dash, thats the point , to stop comms with ezs!

15 minutes for a W211 and W203 EZS? Please make a video.
I want to know how to do this.

[enigmauk]

Why would you want a 211 or 203 to go obd?
During your 15min wait. I could have removed the ezs , done the miles, took the cluster out and done it from the back of the dash.............


bat nball..."Some 211 go by OBD but it only flashes the dash doesn't touch the ezs
Same as doing it through dash plug" .
Well why would it touch the ezs? [if it where to flash the dash, thats the point , to stop comms with ezs!

lol i dont use obd option only tried it as it never seems to work anyway... i usually just flash the dash using cluster plug unless the customer requests the ezs to be done properly... in which case it would take 15 minutes... :D

[enigmauk]

15 minutes for a W211 and W203 EZS? Please make a video.
I want to know how to do this.

why video?

2minutes - just pull out the ezs
4minutes - take speedometer out... pull off the surround and then 3 more screws
8minutes - while walking over to soldering station pull apart the ezs... solder the wires on and program the mileage....
10minutes - cluster plug to do the dash
15minutes - then run back to the car and put it back to together

you can have it done in 15 minutes if you really want... you need to have everything out ready to complete the job as quickly as possible though.

[gcesare21]

why video?

2minutes - just pull out the ezs
4minutes - take speedometer out... pull off the surround and then 3 more screws
8minutes - while walking over to soldering station pull apart the ezs... solder the wires on and program the mileage....
10minutes - cluster plug to do the dash
15minutes - then run back to the car and put it back to together

you can have it done in 15 minutes if you really want... you need to have everything out ready to complete the job as quickly as possible though.


Yes ....lol
the best thing ...
is faster...
and little risk...:party::party::party:

[TULGEYWOODMAN]

15 minutes for a W211 and W203 EZS? Please make a video.
I want to know how to do this.


I dont have a video camera.

[smartymarti]

Dear drpeter
for your hedification............

wtf should I make a video?

Tilt column,remove cluster surround, remove trip button,
loosen 4 torx screws, pull out cluster and unplug. 1 minute

connect cluster plug and reprogramme 2 minutes.

remove kick panel screws, remove ezs lock ring,
disconnect bowden cable and 2 connections from ezs, 2 minutes

remove 2 torx from ezs casing and split casing,
solder rosfar connections,reprogramme 3 minutes


desolder, and rebuild ezs, 1 minute.

replace plugs and bowden cable, 1 minute.

refit ezs and locking ring,refit kick panel and screws 1 minute

Reconnect cluster, refit and tighten 4 torx screws 1 minute

Replace trip button and cluster surround, 1 minute

Start car, drink tea, eat toast 2 minutes

used to be a lot quicker when I was younger


Eric you missed recieve payment from customer on your in depth description , please amend with imediate effect

[puiu]

Tryed today to make a Touareg 2010 color display
try by OBD - error
removed the dash and the 95320 - made a backup of eeprom,i selected menu Touareg 2010- (7P)-95320 and Digiprog say "Attention Read Manual" ??? but i have no pdf for this one :(
i press ok - done - "memory erased" (I was a little nervous, but I had backup :) )
put all back,on display its show : 0 km !
try again by OBD new value is writen ok
:proud:

Puiu

[antibisic]

Tryed today to make a Touareg 2010 color display
try by OBD - error
removed the dash and the 95320 - made a backup of eeprom,i selected menu Touareg 2010- (7P)-95320 and Digiprog say "Attention Read Manual" ??? but i have no pdf for this one :(
i press ok - done - "memory erased" (I was a little nervous, but I had backup :) )
put all back,on display its show : 0 km !
try again by OBD new value is writen ok
:proud:

Puiu


So it was like in bmw 35080 first erase and later put orig back and program?

[puiu]

I say more like the service Mode with VDP for Golf 6 ...

Puiu

[drpeter]

Right and I am the real Santa.

Verstuurd van mijn GT-N7000 met Tapatalk

[enigmauk]

Dear drpeter
for your hedification............

wtf should I make a video?

Tilt column,remove cluster surround, remove trip button,
loosen 4 torx screws, pull out cluster and unplug. 1 minute

connect cluster plug and reprogramme 2 minutes.

remove kick panel screws, remove ezs lock ring,
disconnect bowden cable and 2 connections from ezs, 2 minutes

remove 2 torx from ezs casing and split casing,
solder rosfar connections,reprogramme 3 minutes


desolder, and rebuild ezs, 1 minute.

replace plugs and bowden cable, 1 minute.

refit ezs and locking ring,refit kick panel and screws 1 minute

Reconnect cluster, refit and tighten 4 torx screws 1 minute

Replace trip button and cluster surround, 1 minute

Start car, drink tea, eat toast 1 minute 59 seconds

Snatch money off punter 1 second

used to be a lot quicker when I was younger

Wow 13 minutes and even time to snatch the money... your a pro!

[drpeter]

Tryed today to make a Touareg 2010 color display
try by OBD - error
removed the dash and the 95320 - made a backup of eeprom,i selected menu Touareg 2010- (7P)-95320 and Digiprog say "Attention Read Manual" ??? but i have no pdf for this one :(
i press ok - done - "memory erased" (I was a little nervous, but I had backup :) )
put all back,on display its show : 0 km !
try again by OBD new value is writen ok
:proud:

Puiu


This has nothing to do with service mode, more with virginise. With VCDS you can program km on a new dash (0 Km). Now you understand why you saw 0 km on your dash.

[puiu]

This has nothing to do with service mode, more with virginise. With VCDS you can program km on a new dash (0 Km). Now you understand why you saw 0 km on your dash.


I know that,it was just a stupid answer ....
you are right :)
without any documetation,when i saw that is not asking me to put new km,i was i litle bit worried,but after i put all back and its show 0 Km ,my first thought was to use the VCDS to put new value,but i try with Digiprog and all was ok .

[captain crackers]

Tulgeywoodman, you should realise. The air is thin in the Netherlands and a lack of oxygen will slow anyone down. If you are now taking 13 minutes to strip, program and refit an EZS, may I suggest turning up the oxygen valve, just like the doctor told you. Arthur.

[TULGEYWOODMAN]

thatismuchbetterthankyouverymuchoxygennowsetatmaxi mumbutmyheartbeatisgettingveryfastithinkimustchews ometulipleavestocalmmyselfdownatthisrateithinkicou lddothemercedesezsandclusterintenminutesnow





sorry, I inhaled the wrong gas again.

[wadim21]

some body tried Skoda fabia 2008 crypto? via OBD?

[Ding-Dong]

Dear drpeter
for your hedification............

wtf should I make a video?

Tilt column,remove cluster surround, remove trip button,
loosen 4 torx screws, pull out cluster and unplug. 1 minute

connect cluster plug and reprogramme 2 minutes.

remove kick panel screws, remove ezs lock ring,
disconnect bowden cable and 2 connections from ezs, 2 minutes

remove 2 torx from ezs casing and split casing,
solder rosfar connections,reprogramme 3 minutes


desolder, and rebuild ezs, 1 minute.

replace plugs and bowden cable, 1 minute.

refit ezs and locking ring,refit kick panel and screws 1 minute

Reconnect cluster, refit and tighten 4 torx screws 1 minute

Replace trip button and cluster surround, 1 minute

Start car, drink tea, eat toast 1 minute 59 seconds

Snatch money off punter 1 second

used to be a lot quicker when I was younger


u r still young to do all this in 15 minutes

[rukartinatv]

I know that,it was just a stupid answer ....
you are right :)
without any documetation,when i saw that is not asking me to put new km,i was i litle bit worried,but after i put all back and its show 0 Km ,my first thought was to use the VCDS to put new value,but i try with Digiprog and all was ok .

but how you did porshe obd2 if its no option in digiprog?
only eprom ????

[ALEXEI]

but how you did porshe obd2 if its no option in digiprog?
only eprom ????

it was about Tourareg.
but if you want to know I did one Cayene obd all ok
my AVDI didnt seen it.

[nomis]

To Eric ! Why you change this (http://img835.imageshack.us/img835/4809/avatar1077562gif.jpg) avatar ? I love this ... You are looking smart, young, decent, in this avatar if it is real..& of course? lol lol lol ..

[rukartinatv]

it was about Tourareg.
but if you want to know I did one Cayene obd all ok
my AVDI didnt seen it.

cayene 2011 12 you did obd? with digiprog or avdi?

[TULGEYWOODMAN]

To Eric ! Why you change this (http://img835.imageshack.us/img835/4809/avatar1077562gif.jpg) avatar ? I love this ... You are looking smart, young, decent, in this avatar if it is real..& of course? lol lol lol ..

Here is pic taken of me today



[you dont think my coat looks too big for me do you?]

[javyb]

Has anyone managed to do s CAS 3 BY OBD using ST16 lead with digiprog???

[honingkoning]

Has anyone managed to do s CAS 3 BY OBD using ST16 lead with digiprog???

I was able to read correct milleage on cas 3 but i did not programmed new milleage due to no time to play.
But i think it works good.

Regards Adam.

[PremierD]

Yes it works ...

[tatop]

Yes it works ...

List of Fiat alfa lancia by Obd?


Inviato dal mio GT-P1000 usando Tapatalk

[nomis]

you dont think my coat looks too big for me do you?
No..... never ..don't hurt..

GOD Bless You.

[carradio2001]

How solve Audi A4 2005 2.0 on ECU EDC16 ?

Carradio2001.

[saadoun]

hello
is there anyone who tried the golf 5 2007 year odometer manetti marelli by obd?
thanks

[drpeter]

Dear drpeter
for your hedification............

wtf should I make a video?

Tilt column,remove cluster surround, remove trip button,
loosen 4 torx screws, pull out cluster and unplug. 1 minute

connect cluster plug and reprogramme 2 minutes.

remove kick panel screws, remove ezs lock ring,
disconnect bowden cable and 2 connections from ezs, 2 minutes

remove 2 torx from ezs casing and split casing,
solder rosfar connections,reprogramme 3 minutes


desolder, and rebuild ezs, 1 minute.

replace plugs and bowden cable, 1 minute.

refit ezs and locking ring,refit kick panel and screws 1 minute

Reconnect cluster, refit and tighten 4 torx screws 1 minute

Replace trip button and cluster surround, 1 minute

Start car, drink tea, eat toast 1 minute 59 seconds

Snatch money off punter 1 second

used to be a lot quicker when I was younger

Please post a video, just like your volvo movie, we know that you are fast;

traktor racing volvo terror - YouTube (http://youtu.be/9yHl24QynOM)

[batandball]

Please post a video, just like your volvo movie, we know that you are fast;

traktor racing volvo terror - YouTube (http://youtu.be/9yHl24QynOM)


FAF
LOL:bike::fight:

[wadim21]

VW Sharan 2008 dash OBD --ok

EDC 16 U31 via OBD not work( can`t write new mileage)

2.0 TDi

[TULGEYWOODMAN]

Please post a video, just like your volvo movie, we know that you are fast;

traktor racing volvo terror - YouTube (http://youtu.be/9yHl24QynOM)

Its a quick way to get to the pub

[binken]

Today i test digiprog 3 to make dash eeprom 95020 citroen berlingo 2012 dont work "unknown version "
had to do it manually!!

[autocargo]

Please anyone have pinout for digiprog OBD adapter? Mine is not working...tried on few cars allready... Like any other clones they could have been wrongly soldered from D9 connector to OBD adapter.
Here's a picture of mine, need to know which one goes where on D9 connector. Many thanks.

Regards.

[gijsvm]

Mercedes CLK W209 from 2003 did not work by obd.
Make it with smelecom and dashplug and work.

[marcio1758]

Please anyone have pinout for digiprog OBD adapter? Mine is not working...tried on few cars allready... Like any other clones they could have been wrongly soldered from D9 connector to OBD adapter.
Here's a picture of mine, need to know which one goes where on D9 connector. Many thanks.

Regards.

DB9 PLATE OBDII
1 = 3
2 = 7
3 = 4
4 = 6
5 = 1
6 = ND
7 = 2
8 = 8
9 = 5

[SEAT.]

Anybody know how to use this Merc W203 cable#St49,it's for 01-04 diag.
Thanx.

[batandball]

Anybody know how to use this Merc W203 cable#St49,it's for 01-04 diag.
Thanx.

thats the old lead for doing it through interior light, use obd lead or dash plug lead

[SEAT.]

Its only shows me the st49 cable in the menu,but the 04- it shows me plug 60 &16.

[batandball]

Its only shows me the st49 cable in the menu,but the 04- it shows me plug 60 &16.

st 60 or 16 use them
you may have to trim the plug edge to make it fit

[sterling]

Is there such a probe adapter ST59 ??

[nebojsapejcic]

Anyone tried this version with red casing

???????????? ???? - DIGIPROG 3 (http://strelkosiemnik.ucoz.ru/index/digiprog_3/0-14)

DSCN4802 - YouTube

they say it is better quality , made in poland , or is it same china in red box?

I have read here about red case digiprog 3, someone said it works 100% , can anyone confirm

[nebojsapejcic]

it's made in Poland , costs 1500 and doesn't kill dasboards , that's the answer I got. Anyone have this?

[TULGEYWOODMAN]

it's made in Poland , costs 1500 and doesn't kill dasboards , that's the answer I got. Anyone have this?

Well why pay that much when chinky ones dont kill dashboards either and only cost ?20.?

[PremierD]

lol lol lol

[batandball]

:congrats: :party: lollol

[drpeter]

Only the paint is from Poland mine is original red

Verstuurd van mijn GT-N7000 met Tapatalk

[nebojsapejcic]

Only the paint is from Poland mine is original red

Verstuurd van mijn GT-N7000 met Tapatalk

How much does your cost? Any link where to buy?

[TULGEYWOODMAN]

How much does your cost? Any link where to buy?

?4 per litre from B&Q....[post office red]