Digiprog 3 clone questions and answers

[Shmortz]

yes it was working on many W203 clusters, 4+6 also working, because 4 and 5 are shorted in W203 dash as I sad in my previous post, so 4+6 = 5+6 for W203, but the best is to use 4+6 for all MB dashes of that type...

[dyc]

mb glk 2012 read wrong milage value not tried to write :)

[u.s]

What was original miles and what value did it read?
I found when reading a Toyota that the Digi thought it was in KM and then converting it miles.

[gregc83]

I checked the plug st 60/2 connection today, please guys look is good or not I attach a photo:

black plug:
1 - green
5 -orange
6 - yellow
17 -white
18 - black

grey plug:
1 - yellow + orange
2 - green
4 - black
5 - white
209807

[gregc83]

Clio 08 -st 01 - works OK via CHIP
yaris 06 - st 01 - read wrong milage not tried to write new value
mazda 6 - st - 01 - read wrong milage not tried to write new value

[will4u69]

Renault master 2010 read and write ok, read miles but was km, but easy to work out and same on write

[bersch8688]

Mazda 6 2006 ---> Clip OK Work
VW Passat 2000 ---> OBD OK Work

[rukartinatv]

Clio 08 -st 01 - works OK via CHIP
yaris 06 - st 01 - read wrong milage not tried to write new value
mazda 6 - st - 01 - read wrong milage not tried to write new value
Try to swape bites on the dump.
sometimes bites swapt if someone program with another programer!!!

[u.s]

Try to swape bites on the dump.
sometimes bites swapt if someone program with another programer!!!

I've said it before, but what I think is happening is that the digi is reading the miles but thinks it is in km and changes it to miles when it shows you on the screen.

E.g car miles is xxxxx, digi reads it and thinks it's km so converts it to miles and shows you yyyyy.

[JustMeAgain]

Clio 08 -st 01 - works OK via CHIP
yaris 06 - st 01 - read wrong milage not tried to write new value
mazda 6 - st - 01 - read wrong milage not tried to write new value

yaris 06 works. Read mileage as KM
Mazda 6 works. Read above, exercise logic, and learn a little remedial mathematics and logic.

[lupu_sandu]

Iveco 2008 executed today using Ducato 2007 menu and yellow adapter for Fiat (for Multiecuscan users ;) )

[lupu_sandu]

I checked the plug st 60/2 connection today, please guys look is good or not I attach a photo:
.....
Read this please:
http://www.digital-kaos.co.uk/forums/f174/digiprog-3-clone-questions-answers-282850/index134.html#post2032728

[djnesio]

Hi guys.

I have a problem with a Xsara Picasso dashboard.

This dash has a 93c66 eeprom. I have read it with Digi and it reads them succesfully, then I modified and wrote in dash.

Now, when I start the car, the dash doesn't show the total and partial mileage,nor current speed and some warning lights keep on all the time.

The lexia tool connects with all car systems but not with the dash.

Any idea?

[teerak2uk]

Hi guys.

I have a problem with a Xsara Picasso dashboard.

This dash has a 93c66 eeprom. I have read it with Digi and it reads them succesfully, then I modified and wrote in dash.

Now, when I start the car, the dash doesn't show the total and partial mileage,nor current speed and some warning lights keep on all the time.

The lexia tool connects with all car systems but not with the dash.

Any idea?

Right your original dump back to it

[xanubysx]

Hi guys.

I have a problem with a Xsara Picasso dashboard.

This dash has a 93c66 eeprom. I have read it with Digi and it reads them succesfully, then I modified and wrote in dash.

Now, when I start the car, the dash doesn't show the total and partial mileage,nor current speed and some warning lights keep on all the time.

The lexia tool connects with all car systems but not with the dash.

Any idea?

read eeprom and post here....

[Shmortz]

allmost all adapters on my digi are wrong, here is pinout of ST60/2 my adapter after repair it:

ST 60/2 DB25 --> dash 18pin


black 13 --> black 1
brown 12 --> brown+green 5,6
red 9 --> red 17
yellow 10 --> yellow 18

don't you read, here is pinout of my working adapter, your pinout on DB25 is wrong, also you must move orange to pin 4 on black plug


I checked the plug st 60/2 connection today, please guys look is good or not I attach a photo:

black plug:
1 - green
5 -orange
6 - yellow
17 -white
18 - black

grey plug:
1 - yellow + orange
2 - green
4 - black
5 - white
209807

[nebojsapejcic]

Hi guys.

I have a problem with a Xsara Picasso dashboard.

This dash has a 93c66 eeprom. I have read it with Digi and it reads them succesfully, then I modified and wrote in dash.

Now, when I start the car, the dash doesn't show the total and partial mileage,nor current speed and some warning lights keep on all the time.

The lexia tool connects with all car systems but not with the dash.

Any idea?


xsara picasso with 1 dash plug you have to swap file, with 2 plugs writes ok.

[djnesio]

Right your original dump back to it

I have read and saved the eeprom with Digi, but now How could I download to the PC ?

[PremierD]

Search on here for EEtool

[djnesio]

read eeprom and post here....

210024

This is the eep file from the dash.

Now has 32x.xxx kms

After, I would like 127.888 kms

Thanks in advance

[PremierD]

you have 127888 on it mate ..

C6E08DF11BE337C66F8CDF18BE317C63
F8C6F18DE31BC6378C6F18DF31BE637C


I think lol

[djnesio]

you have 127888 on it mate ..

C6E08DF11BE337C66F8CDF18BE317C63
F8C6F18DE31BC6378C6F18DF31BE637C


I think lol

I read 32x.xxx and wrote 127.888 using the car/truck function , but when I connect it in the car the dash doesn't show the total and partial mileage,nor current speed and some warning lights keep on all the time.

The lexia tool connects with all car systems but not with the dash.

I don't have the original dump, only the actual dump that has these problems.

Now with the eeprom function I read this, but the Tachosoft says me to put this :

127888km = E0C6C18D831B06370C6E18DC31B86370C6E08DC11B8337066E 0CDC18B8317063

Then, I understand the Digi doesn't work properly.

[PremierD]

Why ask for assistance and give the correct information after ..Tacho shit is wrong ... you have corrupted the original dump . a lesson for the future .. SAVe SAVE and SAVE again .. then change .. now you are looking for an original dump I think ..

C6E08DC11B8337066E0CDC18B8317063
E0C6C18D831B06370C6E18DC31B86370


That is 127,888 kms .. if you used digi then its wrong only the first byte was correct

[djnesio]

Why ask for assistance and give the correct information after ..Tacho shit is wrong ... you have corrupted the original dump . a lesson for the future .. SAVe SAVE and SAVE again .. then change .. now you are looking for an original dump I think ..

C6E08DC11B8337066E0CDC18B8317063
E0C6C18D831B06370C6E18DC31B86370


That is 127,888 kms .. if you used digi then its wrong only the first byte was correct


I don't understand why for 127.888kms Digi calculates one codification, Tachosoft 23.1 calculates other and you have other different.

Which is the program that you are using?

[PremierD]

I'm using Hex workshop and Brain.exe mate ..

Tacho shit need to be byte swapped .. Diga is just plain shit in that dump anyway .. so take your pick .. :)

btw .. the algo is VDO rolling encryption .. hex inverted /16/8/4/2.. for first 4 bytes .. first nibble to last for next 4 . then byteswap the next 8 bytes .. really simple once you learn it ..

[olo_3]

where can I buy it?

Digiprog HC12 - YouTube (http://www.youtube.com/watch?v=aQzvkgs6RoM)

[Cardiag.ru]

where can I buy it?

Digiprog HC12 - YouTube (http://www.youtube.com/watch?v=aQzvkgs6RoM)
However, I am the good operator :)

[PETAR]

w211 2007 not work obd
w169 not work obd

[lupu_sandu]

Maybe on your clone, i make a W211 2007 via obd.

[djnesio]

I'm using Hex workshop and Brain.exe mate ..

Tacho shit need to be byte swapped .. Diga is just plain shit in that dump anyway .. so take your pick .. :)

btw .. the algo is VDO rolling encryption .. hex inverted /16/8/4/2.. for first 4 bytes .. first nibble to last for next 4 . then byteswap the next 8 bytes .. really simple once you learn it ..


Tomorrow I will try with your codification.

According Tachosoft, the codification should be in thes lines:


0000: xx xx ED F0 DB E1 B7 C3 6F 87 DF 0E BF 1D 7F 3B
0010: FF 76 F0 ED E1 DB C3 B7 87 6F 0E DF 1D BF 3B 7F
0020: 76 FF xx xx xx xx xx xx xx xx xx xx xx xx xx xx

Do you agree?

Thanks

[bersch8688]

Mercedes Vito 2010 Dashboard ---> 25LC640 Work Clip OK

PS:
Mercedes Vito 2010 EZS ---> EDR Pauli 9S12X Gold (Clone) 0L01Y Work Good

[PremierD]

Tomorrow I will try with your codification.

According Tachosoft, the codification should be in thes lines:


0000: xx xx ED F0 DB E1 B7 C3 6F 87 DF 0E BF 1D 7F 3B
0010: FF 76 F0 ED E1 DB C3 B7 87 6F 0E DF 1D BF 3B 7F
0020: 76 FF xx xx xx xx xx xx xx xx xx xx xx xx xx xx

Do you agree?

Thanks

Mate .. I think I gave you the top two lines .. you need to move it one byte to the left ..

[bonux]

please post working pinout for ST27 focus cable? no connection with supplied clone plug. thanks

[Shmortz]

there is info for digi cables: http://www.digital-kaos.co.uk/forums/f174/digiprog-3-clone-questions-answers-282850/index132.html#post2026374

[kappaca]

Hello everyone I have the version 4.82 you can upgrade to version 4.92?

[PremierD]

Yes mate . of course you can .. you may have to write it yourself though , because the latest version available to the original Digi .. is 4.91 .. but if you can, feel free to enlighten us how its done .. :)

[rukartinatv]

Hello everyone I have the version 4.82 you can upgrade to version 4.92?
only to version V4.96
If you want search on the forum some one posted file for all digiprog numbers

[kappaca]

I have the clone version 4.82 you can upgrade to 4.96?
how can you do?

[PremierD]

Mate .. your chain is being yanked lol.. everyone has 4.82 (with a few exceptions) :) If you can find a newer version to buy, then do so latest is 4.91 .. Good Luck

[securipro38]

Hi
Can someone tell me ho to connect ST41 on AUDI A3 MAGNETI MARELLI (HC12 ) there a 2 plug ok but there ar 2 wire
Thanks

[kizagt]

It must be like with Tacho pro. See picture
I did one with X-prog
211015

[drkyra]

Digi works OBD with A3 MM.

Olny if Display shows 999999 km - rewrite old mileage, then use cable 41.

[waldi1979]

Iveco 2008 executed today using Ducato 2007 menu and yellow adapter for Fiat (for Multiecuscan users ;) )


I tested it and worked great.
The adapter's diagram...

[PETAR]

vw golf6 plus work via obd

[javyb]

I tested it and worked great.
The adapter's diagram...

Does Iveco daily use same OBD connection (wiring) as grande punto for mileage change. What about punto evo and ford ka cheers

[sashxxx]

golf5 visteon repair- function missing. do you have like this?211277

[PremierD]

Everyone has this mate ... lol

[gregc83]

Hi
Can someone tell me with cabel I need to use to do mercedes EZS , manual show me cabel HC12 or HCS12 I was chuck all cables what I have but can't find it :(

also dont know for what is connection ST42/2

Thanks for help

[twincam]

Just forget about this becouse there is no HC12 dongle with clone Digiprog.

[teerak2uk]

Hi
Can someone tell me with cabel I need to use to do mercedes EZS , manual show me cabel HC12 or HCS12 I was chuck all cables what I have but can't find it :(

also dont know for what is connection ST42/2

Thanks for help

Depending on type old use rosfar r260 or r270 (not sure how good r270 is)

New type use can blocker

[gregc83]

so how I can do EZS I need other tools ? do you have any idea? What will be if I change millage only in the dash? in cars (w211,w203 and w209)

[twincam]

Yes,You need programmer like a rosfar,Smokprog ,If You will not do the EZS and difrence in mileage will be more than 250-500km dash will show something like this----- instead of mileage.In this type o car You need also do the Assyt module becouse there are all services with mileage.

[securipro38]

Digi works OBD with A3 MM.

Olny if Display shows 999999 km - rewrite old mileage, then use cable 41.
Thanks worked fine :):dog:

[TULGEYWOODMAN]

Yes,You need programmer like a rosfar,Smokprog ,If You will not do the EZS and difrence in mileage will be more than 250-500km dash will show something like this----- instead of mileage.In this type o car You need also do the Assyt module becouse there are all services with mileage.

not just assyst matey.............LOTS of other kms locations in the car.

[twincam]

Yes, but for beginner like him it's enough information for now:-)

[TULGEYWOODMAN]

oh. sorry, and heres me thinking the only way to da a job was properly!

I stand corrected.

[waldi1979]

When and how can I use this adapters?

[autocargo]

When and how can I use this adapters?
There's plenty of information here.... Anyhow your digiwigi will tell you when and what to use. Also have a look on the pdf's that comes with the clone. One adapter is for BMW cas units and the other is for Mercedes (I think...)

[electrohicham]

is it possible yet to update from version 4.82 to 4.85 ?

[Alex_G]

Hello,

Has anyone successfuly change mileage on this car with CLON DigiProgIII?

Thanks,
Alex_G

[smartymarti]

id have thoughts so as its only a nec with 24c32

[blacktoy]

does anyone have the pinout of the Golf 3 VDO/MM connector (28 PIN) to dash?
The cable which was with my digi is missing this connector (only mercedes C class adaptor is attached.

br

[PremierD]

Removed details of Update .. for checking ... .............

[Becoacamba]

fiesta 2005 obd ok 5sec

what model of dash, how you do it?

[gedas8899]

hello it posible with digiwigi do this cars
w164 2007mod
w220 2001mod ?
thanks

[teerak2uk]

hello it posible with digiwigi do this cars
w164 2007mod
w220 2001mod ?
thanks

Yes it will do them

[gedas8899]

Yes it will do them
it doing by obd or first need do ezs.
this is my firs mb

[xyznia]

w220 100% needs ezs rewrite to 0km, w164 need can filter if digi can't rewrite dashboard flash,w211 no problem works dash+flash obd

[gedas8899]

witch better programmer do ezs
for w220, r260 or r270?

[javyb]

witch better programmer do ezs
for w220, r260 or r270?

R260 I don't trust R270

[buga37]

witch better programmer do ezs
for w220, r260 or r270?
r270 did not do the job on mini cooper 2003 same mask as in w220 (3K91D)

[xyznia]

r270 works very good with secured 9s12 and m35080,i use it for bmw cas and dash many times,my friend did few ezs with 908 inside with r270 too.

[gedas8899]

thanks guy for help i have bouth so find out.

[kappaca]

Hello everyone can anyone tell me how to change km in the automatic transmission ECU audi a4 2009?

[Hazzard]

VW gollf 2002 Instrument cluster rb4 very fine 15 min by Obd O.K

[javyb]

VW gollf 2002 Instrument cluster rb4 very fine 15 min by Obd O.K

Does it display old mileage? And does it ask for a login code like the old TU used to

[bersch8688]

Audi A4 2005 ---> OBD Work

[cotymoto]

Citroen jumpy 2006 Jaeger hc08 not working

Enviado desde mi LT30p usando Tapatalk 2

[PremierD]

Thats because it don't do any 908's mate ... :)

[cotymoto]

Digiprog not work with any HC08?. I and searched for Fiat scudo jaeger.
Enviado desde mi LT30p usando Tapatalk 2

[Hazzard]

No display old km, old zero??? and find code 0x0673 thats all 15 min.process km in dash new? DASH RB4?

[buga37]

Mini Cooper 2003 (mask 3K91D)Direct Connection ----->Not Ok, Cluster don't work property after trying

[buga37]

Can someone tell me if mileage needs to be corrected somewhere other then cluster on Mini Cooper 2003 ?

[88diablo]

For correct job LCM and EWS needs doing but mileage won't jump back if you just do cluster.

[RCS]

Passat 2010 obd ok

[xanubysx]

Seat Altea 2011 dash ok
Fiat doblo 2006 dash ok
Octavia 3 1.6tdi dash ok
Seat Leon Fr 2010 dash ok
Golf 6 2012 dash ok
Peugeot TEPEE Bsi and dash via chip clip ok
Fiat Doblo 2004 ok via obd
Skoda Fabia 1.4 16 v 2007 ok via obd
VW GOLF IV RB8 ( 2001 110kw ) via obd ok
Audi A3 2008 via obd ok
Ford C max dash via obd ok
Ford Mondeo 2008 dash via obd ok
Audi TT 2004 dash via obd ok
Ford CMAX 2006 Benzine.. dash via obd ok
Skoda Fabia 1.4 16v 2003 dash via obd ok
VW Touran 1.9 2007 dash end ecu via obd ok
YETI 2012 dash via obd ok
Skoda Octavia 2011 1.6tdi dash via obd ok
Audi A3 tdi 2007 via obd dash and ecu ok
Daihatsu Feroza benzine 2002 - via clip ok dash, only must desolder eeprom...
ALFA ROMEO BRERA - via clip dash ok
BMW E46 1999 - via obd dash ok
FORD FOCUS 2003 - via clip dash ok
FORD FOCUS 2009 - via stecker 48 dash HCS12 no work !!!
Fiat Ducato 2006 - via clip dash ok , must desolder eeprom and connect on table ...on the pcb no work...
Jeep Cherokee 2004 dash ok via reduction stecker pinout on pcb
Suzuki Grand Vitara 2007 via clip dash ok
Deawoo Matrix benzine via cllip dash ok
Deawoo Matiz benzine via cllip dash ok
Toyota Yaris VVT-i benzine via clip dash ok
Hyundai Getz - Diesel - via clip no work... unknow dashboard DPIII ... must desolder and use NYO r\w C46 ...

update late .....

[felix_fetche]

hi,
what about MB W212 or W204 by OBD ?
or wich other too do this by OBD ?

[bersch8688]

hi,
what about MB W212 or W204 by OBD ?
or wich other too do this by OBD ?


You need Flash the EZS or use Can Blocker
Use the Option ---> EZS Diag

[Alex_G]

So first i must take out dash and make prepare eeprom?

or i can just choose TACHO DIAG C32/C64 and that will do the job?

Thank you,
Alex_G


id have thoughts so as its only a nec with 24c32

VW TIGUAN year 2010,... dash + ECU


Hello,

Has anyone successfuly change mileage on this car with CLON DigiProgIII?

Thanks,
Alex_G

[fif]

skoda fabia 2011 (nec processor) by OBD ok, i use vw polo in menu digi

[Alex_G]

Tiguan 2010,... TACHO done, no problem.

TIGUAN -> TACHO DIAG C32/C64

[drpeter]

Tiguan 2010,... TACHO done, no problem.

TIGUAN -> TACHO DIAG C32/C64
A Dodge Caliber 2006 is coming in tomorrow, someone tested this car with digiprog 3, chrylser 300C menu by OBD? Lot of work to remove dash. Thanks.

[bersch8688]

Chrysler 300C OBD work OBD Digiprog

[PremierD]

Chrysler 300C OBD work OBD Digiprog

Correct .............. lol

[drpeter]

Chrysler 300C OBD work OBD Digiprog
Of course!!!! Crossfire 2005 and 2007 also ok b y OBD but my question is Dodge Caliber by OBD? Never mind I will let you know tomorrow.

[gregc83]

Ford Transit 2004 CHIP 93C76 NOT WORKING - NO CONNECTION . Anyone know how to do this clock?

[buga37]

2010 Dodge Caravan ----->OBD Ok

[XmoDDeR]

2010 Dodge Caravan ----->OBD Ok

But no SRI what do you do about SRI . the purpose of this trade is to do the best job correct? If we do have the job then what??
I just asking??

[superbajer]

I BOUGHT DIGIPROG3 AND WORKS WITH VAG, BUT HAS PROBLEM WITH OPEL. READ WALUE FROM DASHBOARD 17.000.000 WHAT IS TATALLY IMPOSSIBLE. ANYONE HAS SIMILAR PROBLEM??

[superbajer]

YES. WORKS. FIRST TIME EVERY LIGHT GONE FROM DASHBOARD AND THAN YOU HAVE TO PROGRAM DASHBOARD ANOTHER TIME. DO NOT WORRY.

[superbajer]

WORKS WITH MICRONAS. TESTED WITH AUDI A3 2008.

[sepistar]

WORKS WITH MICRONAS. TESTED WITH AUDI A3 2008.

please,take off caps lock!
br.

[drpeter]

A Dodge Caliber 2006 is coming in tomorrow, someone tested this car with digiprog 3, chrylser 300C menu by OBD? Lot of work to remove dash. Thanks.Tested with digiprog, digi read the right value (+/-1000km out) tool said write ok but km not changed.

[davecooper47]

Caliber goes via BDM points with any decent tool including the digiprog clone.

[carbandit]

Caliber goes via BDM points with any decent tool including the digiprog clone.

yes but the stripout is torture :joyous:

[antibisic]

Tested with digiprog, digi read the right value (+/-1000km out) tool said write ok but km not changed.

Are you removed batery or fuse?

[buga37]

"Xmodder" the Job well done, I'm not sure what you talking about

[drpeter]

Are you removed batery or fuse?no i was thinking about that but customer did not wanted errors on the dash. So i did not took the risk. And after programming i read the old value by obd so resetting would not help. I saw also that digi reset the dash also.

[drpeter]

BMW Z3 1996 connector dash connector 7 ok

[XmoDDeR]

"Xmodder" the Job well done, I'm not sure what you talking about

Dodge / chrysler has SRI memory it holds miles too digi doesn't do that so the job is not complete on some of these vehicles it will throw a CEL because the km/mls in the cluster don't match the km/mls in SRI.

[teerak2uk]

Dodge / chrysler has SRI memory it holds miles too digi doesn't do that so the job is not complete on some of these vehicles it will throw a CEL because the km/mls in the cluster don't match the km/mls in SRI.

I have done a few 300c and never had this problem

[buga37]

Dodge / chrysler has SRI memory it holds miles too digi doesn't do that so the job is not complete on some of these vehicles it will throw a CEL because the km/mls in the cluster don't match the km/mls in SRI.

I did test drive to make sure it's working ok, i didn't notice anything wrong, i'm sure the guy would be calling me by now

[cotymoto]

nissan terrano 2001 hc08 magneti marelli not working with cable 42.

[beats2006]

Bought a Digi from this seller on Aliexpress - hxxp://www.aliexpress.com/store/111854
when it arrived touch screen wasn't working properly and it was making an alarm sound so I opened it up to find this -
214116

a leg missing off the ST chip and bodged with a wire glued loosely in place.
messaged the seller about it he said hes not sure that's not how its supposed to be :mad-new:

[Fallen]

Bought a Digi from this seller on Aliexpress - hxxp://www.aliexpress.com/store/111854
when it arrived touch screen wasn't working properly and it was making an alarm sound so I opened it up to find this -
214116

a leg missing off the ST chip and bodged with a wire glued loosely in place.
messaged the seller about it he said hes not sure that's not how its supposed to be :mad-new:

Mine was EXACTLY the same.
I did a proper repair and its now ok.
Hopefully you have enough leg left on the chip to solder to.

[xanubysx]

Tested with digiprog, digi read the right value (+/-1000km out) tool said write ok but km not changed.


Reconnect baterry :) Sometimes this helps ...

[beats2006]

I wouldn't no where to start with a repair and my soldering's not great either going to send it back I think or try and get so much back and pay someone here to repair it, needed it aswell.
will a tacho universal do a 07 transit or a 07 audi a3?

[chrismoore02]

I wouldn't no where to start with a repair and my soldering's not great either going to send it back I think or try and get so much back and pay someone here to repair it, needed it aswell.
will a tacho universal do a 07 transit or a 07 audi a3?

Soldering's not good and you do mileage corrections. Rather you than me.

[beats2006]

No need for soldering on an a3 or transit so that's not a problem

[kappaca]

does anyone know if there is a version 4.88

[teerak2uk]

does anyone know if there is a version 4.88
yes there is

[kappaca]

where can I get update

[exe123]

there is even 4.91... :D

[teerak2uk]

there is even 4.91... :D

yes if you have original:joyous: not for clone though

[exe123]

yes if you have original:joyous: not for clone though

That's your opinion :D

[drpeter]

Aveo 2012 OBD ok digiprog clown

[dfi]

Aveo 2012 OBD ok digiprog clown

What's the software version you used ?

Sent from my GT-I9300 using Tapatalk 4

[drpeter]

What's the software version you used ?

Sent from my GT-I9300 using Tapatalk 4The insignia version :-).

[maaxxyy]

Why are some sellers advertising only vw t4 and others vw t5 with software version 4.82?

[786mo]

Yes there is v4.88 if you how ;)

[PremierD]

And 4.90 and 4.91 ... but then you'll know that anyway :)

[maaxxyy]

Do they all do the late vag cars via eobd then?

[PremierD]

only up to mid 2013 mate ...thats all :)

[kappaca]

who can upgrade to version 4.88

[rukartinatv]

No one can upgrade to v4.88
only one seller in russia sell updates
But only for customer who bought digiprog3
from him.
No one else sell this version.
Thank you

[kappaca]

this is the version 4.88?
Digiprog (http://www.obdtool.nl/index.php?route=product/product&path=20&product_id=66)

[PremierD]

I very much doubt it mate .. lol

[kappaca]

is not the version 4.88?

[yannick1800]

this is the version 4.88?
Digiprog (http://www.obdtool.nl/index.php?route=product/product&path=20&product_id=66)

I know for 100% sure he have 4.88, i saw it , but problem is that he not selling this to everyone. only people he know very good!

[yannick1800]

is not the version 4.88?
yes it is!!

[kappaca]

who can know someone have update 4.88

[technobox]

my digiprog have problem when i try to make w204 service reset all start good after 10 min digiprog coming white screen and digiprog not work until its when cold whats the problem
pls help


Sent from my iPhone using Tapatalk - now Free (http://tapatalk.com/m/)

[786mo]

V4.88 is out there and available from a number of sellers.

[kappaca]

you know that sellers year 4.88?

[javyb]

you know that sellers year 4.88?

Yes I do know

[sterling]

I think its a secret

[kappaca]

you can just let us know

[TULGEYWOODMAN]

my digiprog have problem when i try to make w204 service reset all start good after 10 min digiprog coming white screen and digiprog not work until its when cold whats the problem
pls help


Sent from my iPhone using Tapatalk - now Free (http://tapatalk.com/m/)

Is your avatar a picture of the W204?

[technobox]

Is your avatar a picture of the W204?

no man :))


Sent from my iPhone using Tapatalk - now Free (http://tapatalk.com/m/)

[bochen]

VW Amarok 2012 yeaar dash by OBD - ok

[maaxxyy]

Hi has any one purchased this version of the tool and is it any good? Thanks
http://www.sinosells.com/goods-8772-Digiprog+III+Digiprog+3+OBD2+version.html

[teerak2uk]

Hi has any one purchased this version of the tool and is it any good? Thanks
http://www.sinosells.com/goods-8772-Digiprog+III+Digiprog+3+OBD2+version.html

Read the whole thread and decide for yourself as they all started on 4.82 now some even on 4.88 update

[kappaca]

but you can upgrade or not? 4.88

[teerak2uk]

but you can upgrade or not? 4.88

Yes you can

[bersch8688]

where it can update the DigiProg 4.88????

[kappaca]

digiprog who I can update to version 4.88?

[javyb]

digiprog who I can update to version 4.88?

Clear your inbox

[CarDiag84]

Where buy ugrade or who can upgrade?

[kappaca]

procedure deletes messages in the box

[kappaca]

ok done
Clear your inbox

[bersch8688]

in the Update from 4.82 ---> 4.88 is all the option or only the 4.88 option???

[teerak2uk]

in the Update from 4.82 ---> 4.88 is all the option or only the 4.88 option???

It will be all upto and inc what's in 4.88

[jmcartec]

Is there a free way to upgrade or just paying?

I'm interested in any way

[PremierD]

No ............ and this is not a flea market mate .. just use Google ..

[werner5395]

Hello friends. Have a Poblem with Mercedes w204, 2012. I have changed in km ezs first then Dash short time later, the old Miles will be displayed again, what I'm doing wrong. I have do it by obd

[teerak2uk]

Hello friends. Have a Poblem with Mercedes w204, 2012. I have changed in km ezs first then Dash short time later, the old Miles will be displayed again, what I'm doing wrong. I have do it by obd

Esd with what

[javyb]

Hello friends. Have a Poblem with Mercedes w204, 2012. I have changed in km ezs first then Dash short time later, the old Miles will be displayed again, what I'm doing wrong. I have do it by obd

You only have to press EZS and change miles the dash should take miles from EZS

[werner5395]

ezs with digiprog by obd

[werner5395]

i have do it. dash show new km but then i zurn off key the old km come back.

[andkl2810]

Hello ALL !

W212 dash -ok , EZS - ok !!!!!--thereafter--- Dash-show new KM, assyst - 10min- ok , clear err - ok , run 2.2 all good , stop , start and on light check (error - DPF FULL !! ) , go run 60km (80km/h) , clear DPF and clear error --- all GOOD ! this is fantastic - I'm shocked !:congrats:

[javyb]

i have do it. dash show new km but then i zurn off key the old km come back.

Change km in EZS only with engine running. Then adjust assyst then clear error it will work

[maaxxyy]

Still confused about which one to buy, most sellers showing eobd or full cable versions, all with v4.82. But most do not show vw t5 and newer vags and mercs. So my question is - do all the versions do the late vags and mercs etc? Or is it just the ones listed as full kit or eobd? Thanks

[beats2006]

just tried a 2007 Audi a3 via obd and read old miles ok but got dead dash after writing new? sure I've seen someone have this fault on here already but cant find the post. how do I fix it car wont start dash completely blank?

[twincam]

Disconect baterry for a few minutes.

[beats2006]

I can get a connection with digi again but it says old km 0?

[beats2006]

Sorted just re wrote and worked fine

[koba]

hello,


who can make my DigiProg update to 4.88.
Thank you

[javyb]

hello,


who can make my DigiProg update to 4.88.
Thank you

A few people can make update if your willing to pay the money

[carradio2001]

A few people can make update if your willing to pay the money
How much ?
Must send the digi or not ?

Carradio2001.

[Alex_G]

Still confused about which one to buy, most sellers showing eobd or full cable versions, all with v4.82. But most do not show vw t5 and newer vags and mercs. So my question is - do all the versions do the late vags and mercs etc? Or is it just the ones listed as full kit or eobd? Thanks

All same just different cable sets. Just be sure to take "A - Quality" and that's all.

Regards,
Alex_G

[PremierD]

OK .. all this will be done by PM .. or the thread will be binned .. getting to much to be about updates .. and not using ..

[maaxxyy]

Just ordered mine, i'll keep you posted on what is successful.

[Hazzard]

Audi A8 2005,ACC Starts,OBD work fine,one minut.

[werner5395]

Works fine. Thanks for help.

Gesendet von meinem GT-I9070 mit Tapatalk 2

[cotymoto]

Ford fiesta 2004. ObdII not working. Not recognize. Dash. Visteon 24c08

Enviado desde mi LT30p usando Tapatalk 2

[PremierD]

Correct .....lol

[andersonmaxi]

cristian how are u doing ?

[bochen]

Peugeot 206 dash HC05H12 not working , read error.

[theghost]

Hi,

How to solve the following errors:

-not booting -> white screen
-no communication via obd (obd cable is ok).

Br

[teerak2uk]

Hi,

How to solve the following errors:

-not booting -> white screen
-no communication via obd (obd cable is ok).

Br

Return to seller

[Sergei1956]

Chevrolet Cruze 2012 yeaar dash by OBD - ok

[davecooper47]

I thought it was established that the clone digiprog is useless for hc05's and hc08's. It's no surprise when people post their unsuccessful attempts on here.

[greg38]

A few people can make update if your willing to pay the money

I'm interested for update, please pm me

[PremierD]

Nooooooooooooooo.................

[Cardiag.ru]

Nooooooooooooooo.................
Just close that topic :D

[drpeter]

Porsche 911 (997) 2006 ECM 95320 direct not ok. Dash OBD ok, Boxster 2006 dash OBD ok

[justy22]

Somebody must be making a packet out of the Unmentionable, I have a green board been told its too risky to do

[88diablo]

I did 997 ECU the other day and was fine but removed chip to do it.

[Nierka19]

Bmw E39 99 year dash, LCM and CAS is working on digiprog?

[PremierD]

Of course mate .. everything works on the wiggy .. even 99 cas units lol

[drpeter]

I did 997 ECU the other day and was fine but removed chip to do it. I also removed the chip, it reads the wrong km and write was not possible. Was it a 95320? Can you post the dump with actual km? Thanks.

[cotymoto]

Renault traffic 2006 93c66 not working. Wrong dump

Enviado desde mi LT30p usando Tapatalk 2

[88diablo]

I also removed the chip, it reads the wrong km and write was not possible. Was it a 95320? Can you post the dump with actual km? Thanks.

Hi, Sorry my mistake. I thought from memory it was 95320 but Ive checked file and is 95P08. Probably no use but its attached if you need it.

[PremierD]

75,288 km's ? ..................

[88diablo]

Sounds right from memory, and I'm sure you will be :-)

[Hazzard]

Passat 2.0 Tdi AD Blue Year 2009 Black white display working via OBD 40 sec Tacho diag 32/64 Work O.K

[drpeter]

Hi, Sorry my mistake. I thought from memory it was 95320 but Ive checked file and is 95P08. Probably no use but its attached if you need it.

Sorry my mistake digi will calc the ecm on porsche with 95320, you just have to press the ''x'' to select the 95320 chip.
But my script will do km + hours at once with checksum :-). Yes you are right, I wasted time.

[Radek2000000]

Sorry... how fiat grande punto EVO?

[Pakli30]

Grade punto not odb.
chip OK

[Radek2000000]

EVO chip ok???

[teerak2uk]

EVO chip ok???

He means by OBD (ST16) not working but by clip (ST01) is working

[cotymoto]

Vw touran 2008 obd 2 min. Perfect.

Enviado desde mi LT30p usando Tapatalk 2

[Radek2000000]

edc16u31 by audi 95320 obd2 is OK? may diag ecu95320 vwT5- anyone tried?

[sepistar]

edc16u31 by audi 95320 obd2 is OK? may diag ecu95320 vwT5- anyone tried?

have try on several audi edc 16 ecu,but not working,mate.
br.

[u.s]

2010 VW Polo (6R) - prepare 24c32 using ST47, then program by OBD using ST16, reset service, clear errors - all OK

[xtech]

T5 ecu obd 2005 ok ,2006 working but milage not change

[javyb]

2010 VW Polo (6R) - prepare 24c32 using ST47, then program by OBD using ST16, reset service, clear errors - all OK

You can do it straight OBD why did u prepare Eeprom?

[u.s]

doh!!! i just followed instructions mate.
i did see the diag option in digi but that was after i had the cluster back off and ST47 soldered onto board :banghead:

[TULGEYWOODMAN]

T5 ecu obd 2005 ok ,2006 working but milage not change

well that means its not working surely?

[cinici]

2008 year polo magnetti marelli dash obd not work

[honingkoning]

What you mean not work? By obd it Will never work take out dash and do by solder points, i did it and it worked.

Wbr Adam.

[zogo]

I have a digiprog3 but some adapters inadequate wire colors as they appear in the image.for example on the adapter 51 have red,black,orange,braon on picture show braon,white,green,yelow.i dont know how to connect thanks

[davecooper47]

Polo 2008 take out dash????? What are you talking about????? this will definitely go via OBD. If it doesn't your machine is faulty.

[easyobd]

Would chinese Digiprog III do 2009+ Skoda Superb 3T4 1.9 TDI with NEC+24c32 via OBDII?

[teerak2uk]

Would chinese Digiprog III do 2009+ Skoda Superb 3T4 1.9 TDI with NEC+24c32 via OBDII?

Try it and see or search the thread

[easyobd]

Unfortunately I can't have this tool for testing that's why I ask if anybody done it with 2009+ Superb with NEC. I search the thread but, I can't find anything about Superb, only Octavia, Passat and other VAG cars, presume it should work also with Superb, but I had hope that someone can confirm it 100%.

[javyb]

Unfortunately I can't have this tool for testing that's why I ask if anybody done it with 2009+ Superb with NEC. I search the thread but, I can't find anything about Superb, only Octavia, Passat and other VAG cars, presume it should work also with Superb, but I had hope that someone can confirm it 100%.

Of it works on one vw with NEC it will work on the other cos there same dashboards. So don't be shy give it a try

[easyobd]

Thanks, that's what I thought :peaceful:. I just downloaded user manual with pdf-s, and it's say that digiprog 3 does Superb 2008 +, but it also say that to program this dash it has to be done in two steps(manual is in german laguage, so I don't know if google correctly translate it):
1. solder some plug 47 into the dash and then connect with digiprog ....
2. conect the St 16 plug into diagnostic car port and do programming
Is that correct way to do it with Digiprog or can I go straight true OBD- soldering is not a problem for me, but reading this tread nobody mentioned abut dash preparation on VAG cars. I checked Digiprog VW Passat manual and says to same way to do the dash on Passat-but other members said that Passat went straight true OBD?

[PremierD]

Mate .. Plug the dam thing in press read .. if it reads change it .job done ............

[sepistar]

Thanks, that's what I thought :peaceful:. I just downloaded user manual with pdf-s, and it's say that digiprog 3 does Superb 2008 +, but it also say that to program this dash it has to be done in two steps(manual is in german laguage, so I don't know if google correctly translate it):
1. solder some plug 47 into the dash and then connect with digiprog ....
2. conect the St 16 plug into diagnostic car port and do programming
Is that correct way to do it with Digiprog or can I go straight true OBD- soldering is not a problem for me, but reading this tread nobody mentioned abut dash preparation on VAG cars. I checked Digiprog VW Passat manual and says to same way to do the dash on Passat-but other members said that Passat went straight true OBD?

do it through obd.it will work.
br.

[easyobd]

Thanks guys, and sorry for stupid questions, didn't wanted make you angry :black_eyed:
PremierD you must have some nerves for people's like me :applouse:

[javyb]

Thanks guys, and sorry for stupid questions, didn't wanted make you angry :black_eyed:
PremierD you must have some nerves for people's like me :applouse:

Is that why U r called easyobd? U only do easy OBD jobs lol

[honingkoning]

Polo 2008 take out dash????? What are you talking about????? this will definitely go via OBD. If it doesn't your machine is faulty.

H? is talking about a magnetti marelli so with a 912 CPU right.

So h? should take out dash and solder 4 wires.

Wbr.

[bersch8688]

BMW E46 EWS3 ST35 ---> Work (Read & Write)

[burko]

Anyone tested A6 (facelift) 2009-2010 dashboard with dp3 clone?
have done 2005-2008 dashes without problem

thank you in advance
Burko

[bersch8688]

BMW E46 LCM HC11 ST35 ---> Work

[brkic6]

Polo 2008 take out dash????? What are you talking about????? this will definitely go via OBD. If it doesn't your machine is faulty.

Either machine faulty, or not VDO dash (TRW/MM).

[brkic6]

Would chinese Digiprog III do 2009+ Skoda Superb 3T4 1.9 TDI with NEC+24c32 via OBDII?

Yes, tested few months ago, also 2012 goes trough OBD without problem.
Regards,
Vladimir

[88diablo]

Yes did 2011 the other day, took about 25 mins.

[FAP 0ff]

Hi , anyone has a version 4.90 and above ? In return I will do the update for this version 3 of the device.

[kappaca]

which version to you?

[Apolo29]

Does work on Renault Megane III abs+dash?

[PremierD]

Eh! let me think .................................................. .................................................. .....................................No mate it does not .. :)

[FAP 0ff]

which version to you? Now I have 4.89

[PremierD]

Good for you mate .. did you have to sell your soul to get it . :)

[TULGEYWOODMAN]

Yes did 2011 the other day, took about 25 mins.


maybe tool is constipated?:highly_amused:

[motorsport]

25 min very longtime!!! for 2011 NEC 24C64 or 32 ?

[pierre renault]

HI
Someone tested Ford Focus 2000 with ST28?
Thank you

[bersch8688]

Working ST27 Ford Focus?

I have repair the Cable with the digi_conectors.txt file

[tom0077]

Ford Focus ST27 --- OK