VVDI 2 new tool arrived

[manfred2]

I do not understand.
At the moment I have a copy made with the programmer from the second (before adding) counter and the immo data from it, a copy of the eeprom (by obd) of my old counter) and immo data.
What should I write?
Provide my forum dumps?
greetings.

[Maartinj]

Hello.
I have such a problem. I did a counter swap on the VW Caddy 2k5 2016. Everything according to the procedure (dump eeprom, service mode, I swapped org eeprom through obd, then security block from my car) and almost everything
The car starts, zero errors on the meter but the brake assistant does not work.
In the assistant (address 13) is a component protection error. The same error is in the counter (but the counter can be cleared and returns only when I start, for example, change the comfort option using maxi dot).
Does VVDI2 not copy CP from counter to counter?
Is it possible that only the ODIS online option remains?
I have a VAS head but before I buy online access I would like to use all the possibilities. I also have the original carprog and Polish Xtool.
I am asking for a hint.
greetings.
if car is with ACC or 5F unit (CP) you can ONLy swap cluster ONLINE and remove CP/ restore FEC codes.
if you swap immo via tools like VVDI, AVDI, after that Odis will not recognize cluster
so better restore epp, and do it online

[darknezz19]

Cas3+ is safe over OBD AKL and spare? Should I be benching these?

[u.s]

Cas3+ is safe over OBD AKL and spare? Should I be benching these?

i always bench these, have never tried anything over obd.

[u.s]

Xhorse VVDI2 Upgrade
Software Update to V6.7.5
Release Date
2020-05-28
Requires firmware upgrade to V6.7.5

What’s New

VAG V6.7.5
1. Improvement for autodetect VAG immobilizer system
2. Improvement for update FRF, SGO file
3. Bugfix

BMW V6.7.5
1. Improvement for CAS3 key learning
2. Bugfix

Transponder Programmer V6.7.5
1. Improvement for make proximity remote
2. Immobilizer data tool:Asia->Hyundai->Santa Fe->2008-MPC5XX bugfix
3. Improvement for clone ID70/ID83
4. Special chip: Add new ID47 for GreatWall ORA
5. Bugfix

Copy 48 (96 bits) V6.7.5
1. Bugfix

J2534 V6.7.5
1. Bugfix

Online Upate Tool V6.7.5
1. Bugfix

Quick Start V6.7.5
1. Bugfix

Download Link

https://public-ap-southeast-1-1251058331.s3-ap-southeast-1.amazonaws.com/download/product/vvdi2/software/VVDI2-InstallerV675.exe

[cristyand]

Cas3+ is safe over OBD AKL and spare? Should I be benching these?

Spare it's ok I did one today but AKL
I wouldn'd try without backup cas

[immoneard]

Xhorse VVDI2 Upgrade
Software Update to V6.7.5
Release Date
2020-05-28
Requires firmware upgrade to V6.7.5

What’s New

VAG V6.7.5
1. Improvement for autodetect VAG immobilizer system
2. Improvement for update FRF, SGO file
3. Bugfix

BMW V6.7.5
1. Improvement for CAS3 key learning
2. Bugfix

Transponder Programmer V6.7.5
1. Improvement for make proximity remote
2. Immobilizer data tool:Asia->Hyundai->Santa Fe->2008-MPC5XX bugfix
3. Improvement for clone ID70/ID83
4. Special chip: Add new ID47 for GreatWall ORA
5. Bugfix

Copy 48 (96 bits) V6.7.5
1. Bugfix

J2534 V6.7.5
1. Bugfix

Online Upate Tool V6.7.5
1. Bugfix

Quick Start V6.7.5
1. Bugfix

Download Link

https://public-ap-southeast-1-1251058331.s3-ap-southeast-1.amazonaws.com/download/product/vvdi2/software/VVDI2-InstallerV675.exe



For long time in VAG nothing special, Not good at all. Just Bug fix or Improvement . Component protection very old, Immo 5 Adaptation components never was done anything to it and many more things nothing new.

[jokir]

I have a 2012 BW Kessy cluster 7N0 920 870 E, H03, SW 0607 and I want to change in a color cluster 7N0 920 880 N, SW2030


I copied the Immo Block with VVDI 2 into the new cluster, my problem is that when I transfer immo data to a new information panel and install it in the car, the dashboard does not turn on at all.When I press the tart button, the alarm lights do not come on at all and I cannot connect via PC


Could someone help me with right configuration?"

Thanks

[TERMINATOR1000]

Spare it's ok I did one today but AKL
I wouldn'd try without backup cas


The problem is during downgrade , no for AKL or NOT ....

[MVVL]

Hey. On the new version, the program does not detect the device. Install back the old version everything is OK. Installing drivers, as in a help, does not help. What kind of problem? Or is it just me?

[Brat]

Hey. On the new version, the program does not detect the device. Install back the old version everything is OK. Installing drivers, as in a help, does not help. What kind of problem? Or is it just me?

update interface and will work!

[torero233]

nothing new with the update they haven't implemented anything long ago nothing new mqb

[TERMINATOR1000]

Hey. On the new version, the program does not detect the device. Install back the old version everything is OK. Installing drivers, as in a help, does not help. What kind of problem? Or is it just me?


simply plug USB to laptop after install latest V6.7.5 firmware + software

[K1nd3r]

how to prepare mqb dealer key in lost all keys situation? in mqb menu vvdi2 ask to switch ignition on with working key, nonsense

[comizelu]

how to prepare mqb dealer key in lost all keys situation? in mqb menu vvdi2 ask to switch ignition on with working key, nonsensePrepare dealer key with immo data

Sent from my MI MAX 3 using Tapatalk

[comizelu]

how to prepare mqb dealer key in lost all keys situation? in mqb menu vvdi2 ask to switch ignition on with working key, nonsenseYou need immo data and sync file

Sent from my MI MAX 3 using Tapatalk

[ASCM]

simply plug USB to laptop after install latest V6.7.5 firmware + softwareFirst upgrade firmware after that sw
And everything ok

Sent from my SM-J415F using Tapatalk

[immoneard]

I have a 2012 BW Kessy cluster 7N0 920 870 E, H03, SW 0607 and I want to change in a color cluster 7N0 920 880 N, SW2030


I copied the Immo Block with VVDI 2 into the new cluster, my problem is that when I transfer immo data to a new information panel and install it in the car, the dashboard does not turn on at all.When I press the tart button, the alarm lights do not come on at all and I cannot connect via PC


Could someone help me with right configuration?"

Thanks

You need to write complete Immo block form Original cluster. So load original Immo block , then write .

[TERMINATOR1000]

HELLO
Latest polo & ibiza ; MQB A0 ( 2018 + ) are supported ? Any advise ?
Best regards

[autoTkey]

HELLO
Latest polo & ibiza ; MQB A0 ( 2018 + ) are supported ? Any advise ?
Best regards

These only with ODIS with license.

[TERMINATOR1000]

These only with ODIS with license.

thanks but need OEM key or Made In China ?

[autoTkey]

I don't know - haven't used this tool. But I guess it doesn't matter what's the key since ODIS updates info in both car and online in VW servers...

[TERMINATOR1000]

yes of course , online tool !!!

[ASCM]

thanks but need OEM key or Made In China ? i think need oem key from dealer just
For learning with odis,
Odis not have access for preparing
Aftermarket key

Sent from my SM-J415F using Tapatalk

[autoTkey]

Isn't it possible to use VVDI2 to make dealer key and then add it with ODIS?

[comizelu]

Isn't it possible to use VVDI2 to make dealer key and then add it with ODIS?No,
Not for 2018+..

Sent from my MI MAX 3 using Tapatalk

[honda1200]

HI hope someone can answer my question!

On BMW X5 e70 with EGS, Can vvdi2 make key in AKL case with known isn from egs and ecu?

[iamfooser]

Anyone tested their new 8A non smart adapter? Manage to generate transponder but not recognise by immobox. I tried the direct connector to immobox cable.

Regarda



Sent from my SM-G970F using Tapatalk

[whiskeyman]

https://www.digital-kaos.co.uk/forums/showthread.php/830226-xhorse-toyota-8a-adapter-all-keys-lost-First-use!

[ab Locksmith]

Anyone tested their new 8A non smart adapter? Manage to generate transponder but not recognise by immobox. I tried the direct connector to immobox cable.

Regarda



Sent from my SM-G970F using Tapatalk

not yet but hope it will work well........

[lock66]

Xhorse 8A Control Box Cable for all key lost.
Trying to read already taket from a car immobox.Just tried through obd-not working
Corolla 2014 -15 assembly Turkey ,immo box 89780 02150 -Czech Republic,
ERR:7A Unknown immobox version.
There are millions of these cars. All of Europe uses these cars.
Toyota 8A Non-smart Key Adapter for All Key Lost.Do not buy this device. I bought and a loss of $ 200.
https://www.youtube.com/watch?v=U6Ex6AKRGeY&t=51s

[ThiagoArgentino]

HI hope someone can answer my question!

On BMW X5 e70 with EGS, Can vvdi2 make key in AKL case with known isn from egs and ecu?



It depends, which DME is going there?

[labusas]

Hello, Please advise how to setup Techstream Passthru settings so VVDI2 works with Toyota.
Can not get it working

[lupu_sandu]

It depends, which DME is going there?
Depends of nothing. I make thousands of E70/E71 keys. No need ISN from EGS and i never hear of this.
8HP long ISN in EGS same ISN long in ECU. 6HP short ISN in EGS same ISN in CAS.
If you make keys with potato tools maybe you search ISN in EGS

[ASCM]

Depends of nothing. I make thousands of E70/E71 keys. No need ISN from EGS and i never hear of this.
8HP long ISN in EGS same ISN long in ECU. 6HP short ISN in EGS same ISN in CAS.
If you make keys with potato tools maybe you search ISN in EGSWhich tool u used by yourself to program
E71 cas ews3 system, version sw instap-52 and AKL situation?

Sent from my SM-J415F using Tapatalk

[drugowaz]

Lupu Your billionaire..almoast

[lupu_sandu]

AVDI never let me down on E70/E71. I fact AVDI killed only one BMW (X1).

[u.s]

Hello, Please advise how to setup Techstream Passthru settings so VVDI2 works with Toyota.
Can not get it working

No one can get the pass thru working, they might as well remove it

[passiw]

Same here. One of the reasonst for buying it was because it claims to supports passthru. I doesnt work with VW ODIS. Support says that its broken, they cant tell when it'll work. I find it very unprofessional to sell a product with a feature that doesnt work.

[kristikapa]

For me it worked for Honda programing using pass thru

[immoneard]

Anyone try Nec 24c64 with Sw 20xx ,AKL and add key ?
This is still PQ dash , not MBQ.

[rola1971]

Anyone try Nec 24c64 with Sw 20xx ,AKL and add key ?
This is still PQ dash , not MBQ.

yes
put dash to boot mode and read immo data

[mlodywafel]

hi i try to reead aes transponder to renault traffic 3 key but not recognize any idea how to do it


Wysłane z iPhone za pomocą Tapatalk

[TERMINATOR1000]

hi i try to reead aes transponder to renault traffic 3 key but not recognize any idea how to do it


Wysłane z iPhone za pomocą Tapatalk

vvdi2 is to bad for read it , use vvdi key tool !

[niko25]

VW new beetle/2004

VVDI2 I read the ecu and got the PIN and CS end Make diler key
When I adapted the key, the adaptation was completed, but the key does not start the car.

[immoneard]

VW new beetle/2004

VVDI2 I read the ecu and got the PIN and CS end Make diler key
When I adapted the key, the adaptation was completed, but the key does not start the car.

2004 beetle is immo 3 , no need dealer key .Unlock that key , and program it with Pin only .

[niko25]

I tried and so with vvdi2, successful programming but the key does not start the car.
Maybe I should try with vcds ,.
17th block, channel 21, login, adaptation .....

[immoneard]

I tried and so with vvdi2, successful programming but the key does not start the car.
Maybe I should try with vcds ,.
17th block, channel 21, login, adaptation .....
When you said does not start car , does it start and turn off after 2-3 sec or just turn over (Cranking)?

Also is it immo light Flashing or goes away after 2 sec in cluster?

[K1nd3r]

is there any secret on touereg 2010 kessy keyless key programming? buttons and keyless wont work

[p1et]

is there any secret on touereg 2010 kessy keyless key programming? buttons and keyless wont work

I guess not original keyless but chinese replacement?

[niko25]

When you said does not start car , does it start and turn off after 2-3 sec or just turn over (Cranking)?

Also is it immo light Flashing or goes away after 2 sec in cluster?


Learning key with vcds and PIN.
So far I haven't been able to learn any keys, with vvdi2 with immo3.Vvdi 2 doesn't work with vag before 2004.

[K1nd3r]

I guess not original keyless but chinese replacement?
yes, aftermarket keyless and keydyi remote also not working

[p1et]

yes, aftermarket keyless and keydyi remote also not working

I would suspect problem here then

[jodge]

yes, aftermarket keyless and keydyi remote also not working

the chinese keys keyless part are never worked for me

[K1nd3r]

the chinese keys keyless part are never worked for me

keyless i believe, but remote... seems like problem in car

[Faraday]

This ridicilus quene 11 wait 11min

https://uploads.tapatalk-cdn.com/20200625/0c96a6dc8c21d9a6d99bb9272321448b.jpg

[whiskeyman]

not too bad i was 56 other day

[Jimmy07]

I was 43 the other day and 18 on KD lol

[TERMINATOR1000]

for easy cars , better is add key , no queue !

[Jimmy07]

Very true but cloning handy for awkward or modified vehicles

[ghitab]

Anyone try Nec 24c64 with Sw 20xx ,AKL and add key ?
This is still PQ dash , not MBQ.
Not work this new version yet, I tried on new t6. But be careful this is aes key and no more remote learn in bcm

[lock66]

Skoda kodiaq 2019.
VVDI2 + VAG helper can add smart key?

[jodge]

Very true but cloning handy for awkward or modified vehicles

agree it could be a nightmare especially on VAG when the km is modded with cheap stuff

[djollie]

***SOLVED WITH TANGO***

how to move transponder to position 2?

immobox 89780-05030

24c04 dump

726444

726446

[Maartinj]

***SOLVED WITH TANGO***

how to move transponder to position 2? immobox 89780-05030 24c04 dump



everyone who want complain - you can asy use this link
http://www.xhorse.uk/issue

[clauberty]

https://www.digital-kaos.co.uk/forums/showthread.php/623097-Jetta-Tiguan-Keyless-go?p=3129043&viewfull=1#post3129043

from the link above

i have a tiguan with key less entry and go with 1 key

elv vas busted added a second hand elv adapted online

from where i read immo data?

problem is that ecu is bad and cannot read anything from it

Attached is kessy eep

Thank you

[lock66]

everyone who want complain - you can asy use this link

http://www.xhorse.uk/issue

In Device type,need to add "Xhorse VVDI2 Toyota 8A All key lost adapter" This is also a product Xhorse.

[Maartinj]

everyone who want complain - you can asy use this link

http://www.xhorse.uk/issue

In Device type,need to add "Xhorse VVDI2 Toyota 8A All key lost adapter" This is also a product Xhorse.



Toyota 8A can not wortk alone , so you can select VVDi2 because this is your main device

[rob h]

msd812 BMW
Tried reading isn with vvdi2,
I can connect, when i press read isn, i get the message: can not get the unit name!
728039
is this common?
I do not have another tool to read the isn.

[damih]

Hello no one have tryed new option made a key via obd CAS4 in 2min ??
thanks for any feedbach

[rola1971]

Hello no one have tryed new option made a key via obd CAS4 in 2min ??
thanks for any feedbach


yes i tray 5 time i dont know foe my all ok work

[optimaplus]

Hello no one have tryed new option made a key via obd CAS4 in 2min ??
thanks for any feedbach

Hi made cas 4 key today spare key on 2012 X3 5 mins worked ok

[TERMINATOR1000]

i see more fail in this forum .... CAS4 by OBD2 it's like Russian roulette with an Kalashnikov .

[ttzag]

Hello
Read isn from dme then read isn from cas
How to write new isn to the cas?
Need to replace ecu
Car e90 2010 cas3

[rola1971]

Hello
Read isn from dme then read isn from cas
How to write new isn to the cas?
Need to replace ecu
Car e90 2010 cas3


open dump in hex and change what problem

[ttzag]

open dump in hex and change what problem

Done... thanx
But ecu we bought it is for AT trans..
Car start but fan always on and idle very low...
Tried to default coding but nothing
Do you know how to make the ecu for manual transmission?
Or it's impossible?

[rola1971]

Done... thanx
But ecu we bought it is for AT trans..
Car start but fan always on and idle very low...
Tried to default coding but nothing
Do you know how to make the ecu for manual transmission?
Or it's impossible?

last time i only write eeprom from old to new ecu and dont need change any coding
may old automatic and new manual and dont posibility drive if i write only isn
i copy full eeprom and write full eeprom to new

[ttzag]

last time i only write eeprom from old to new ecu and dont need change any coding
may old automatic and new manual and dont posibility drive if i write only isn
i copy full eeprom and write full eeprom to newWich tool you read and write?
My old ecu water damaged can't connect with it

Sent from my HTC U11 using Tapatalk

[rola1971]

Wich tool you read and write?
My old ecu water damaged can't connect with it

Sent from my HTC U11 using Tapatalk

i have x17 and flex and used for read

[immoneard]

Wich tool you read and write?
My old ecu water damaged can't connect with it

Sent from my HTC U11 using Tapatalk

Try Aultel and coding ECU should fix it . Also if you have Online access with Autel , do software update after Coding.

[K1nd3r]

mqb johnson control mileage possible with vvdi2?

[rola1971]

mqb johnson control mileage possible with vvdi2?


still no.i doit in smok

[clauberty]

hello

how to edit power class in dash

i edited immo data and write immo data but after no more ignition and immo message on dash

engine is adapted to dash but power class in engine ecu is FE and in dash is 60

problem is that i receive same part no has ori ecu but with wrong software

car came to me with immo off and

owner say the ori ecu was this 03L907309AE HW H28 SW 0020


SH ecu is with the same part no but is for manual gearbox or different type of gearbox,


i try to code different type of gearbox but coding rejected


Monday,27,July,2020,21:35:31:03905
VCDS Version: Release 20.4.1 (x64) Running on Windows 7 x64
www.Ross-Tech.com (http://www.Ross-Tech.com)




Address 01: Engine Labels: 03L-906-018-CFF.clb
Control Module Part Number: 03L 906 018 E HW: 03L 907 309 AE
Component and/or Version: R4 2.0l TDI H25 9979
Software Coding: 00190010040601080000
Work Shop Code: WSC 00070 000 00000
ASAM Dataset: EV_ECM20TDI01103L906018E 003012 (VW36)
ROD: EV_ECM20TDI01103L906018E_VW36.rod
VCID: AC14A83AC704F6E607-80F8
4 Faults Found:




16703 - Gear Reconition Sensor
P181C 00 [039] - Implausbile Signal
Not Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 2
Fault Frequency: 1
Mileage: 355245 km
Date: 2067.14.22
Time: 01:50:12




Engine speed: 0.00 /min
Normed load value: 0.0 %
Vehicle speed: 0 km/h
Coolant temperature: 27 °C
Intake air temperature: 28 °C
Ambient air pressure: 1000 mbar
Voltage terminal 30: 13.420 V
Unlearning counter according OBD: 40
Neutral position sensor: current transmission angle: 20.00 °
Neutral position sensor: adapted transmission angle: 0.00 °
Adaptation status for transmission neutral position sensor-Bits 0-7: 4
Transmission neutral position sensor voltage: 0 mV
Neutral position sensor: upper adaptation value: 0 mV
Neutral position sensor: lower adaptation value: 0 mV




10092 - Unknown Error Code
P086D 00 [039] - -
Not Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 2
Fault Frequency: 1
Mileage: 355245 km
Date: 2067.14.22
Time: 01:50:12




Engine speed: 0.00 /min
Normed load value: 0.0 %
Vehicle speed: 0 km/h
Coolant temperature: 27 °C
Intake air temperature: 28 °C
Ambient air pressure: 1000 mbar
Voltage terminal 30: 13.420 V
Unlearning counter according OBD: 40
Neutral position sensor: current transmission angle: 20.00 °
Neutral position sensor: adapted transmission angle: 0.00 °
Adaptation status for transmission neutral position sensor-Bits 0-7: 4
Transmission neutral position sensor voltage: 0 mV
Neutral position sensor: upper adaptation value: 0 mV
Neutral position sensor: lower adaptation value: 0 mV




7027 - Software Incompatibility with Transmission Control Module
U0302 00 [167] - -
MIL ON - Not Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 2
Fault Frequency: 1
Mileage: 355245 km
Date: 2067.14.22
Time: 01:50:12




Engine speed: 0.00 /min
Normed load value: 0.0 %
Vehicle speed: 0 km/h
Coolant temperature: 27 °C
Intake air temperature: 28 °C
Ambient air pressure: 1000 mbar
Voltage terminal 30: 13.420 V
Unlearning counter according OBD: 40
Neutral position sensor: current transmission angle: 20.00 °
Neutral position sensor: adapted transmission angle: 0.00 °
Transmission neutral position sensor voltage: 0 mV
selected gear-Bits 0-7: 0




5523 - Engine Start Blocked by Immobilizer
P1570 00 [167] - -
MIL ON - Not Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 2
Fault Frequency: 1
Mileage: 355245 km
Date: 2067.14.22
Time: 01:50:12




Engine speed: 0.00 /min
Normed load value: 0.0 %
Vehicle speed: 0 km/h
Coolant temperature: 27 °C
Intake air temperature: 28 °C
Ambient air pressure: 1000 mbar
Voltage terminal 30: 13.420 V
Unlearning counter according OBD: 40
Immobilizer snapshot A-Sia Error Snap A: 1D 1D 0E
Immobilizer snapshot B-Sia Error Snap B: 1A 00 00








Readiness: 0 0 0 0 1

[clauberty]

if i change power class in dash i cannot re-adapt key, car have key less go

change power class with smok with vvdi same result

can someone advise me please

Thank you

[immoneard]

Why do you think this ECU will work with this car , you have much more problems with Software version then just doing Immo adaptation. ECu is not comparible with Transmission as well , how you going to fix that.
Get correct ECU and problem will be Fixed.

EVL has power class as well , and changing PC in cluster will give you problems that you have with key .

[clauberty]

Why do you think this ECU will work with this car



because i chack in ETKA and for this car this is the right part no but diffent SW

in ecu now i have sw 03L 906 018 E and need

[TERMINATOR1000]

tool fail to read immo data from 2019 Polo , transponder can't be detected too !
( no test with VAG OBD helper )

[comizelu]

tool fail to read immo data from 2019 Polo , transponder can't be detected too !
( no test with VAG OBD helper )It's new Polo...
No tool can do it.

Sent from my MI CC9 Pro Premium Edition using Tapatalk

[honda1200]

tool fail to read immo data from 2019 Polo , transponder can't be detected too !
( no test with VAG OBD helper )

Only solution is dealer key + dealer tool (odis) at the moment!

[TERMINATOR1000]

Only solution is dealer key + dealer tool (odis) at the moment!

OK


It's new Polo...
No tool can do it.


Sent from my MI CC9 Pro Premium Edition using Tapatalk

WHAT KIND of transponder inside new VAG keys , not ID48 AES , not MQB ....

[CarCity]

It's new Polo...
No tool can do it.

Sent from my MI CC9 Pro Premium Edition using Tapatalk


XTOOL PAD2 can do it

[comizelu]

XTOOL PAD2 can do itAre you serious?
Only dealer!

Sent from my MI CC9 Pro Premium Edition using Tapatalk

[CarCity]

Are you serious?
Only dealer!

Sent from my MI CC9 Pro Premium Edition using Tapatalk

Yes Nec++xx AKL eeprom less

https://youtu.be/A9h7RcMY4_Q

[comizelu]

Yes Nec++xx AKL eeprom less

https://youtu.be/A9h7RcMY4_QThat's the old model,up to 2018!

Sent from my MI CC9 Pro Premium Edition using Tapatalk

[TERMINATOR1000]

XTOOL PAD2 can do it

Tested today , now the car is dead !
Car go to main dealer for repair : car need to change ECU + Dash + keys + gear box management ...

[solitaire]

Tested today , now the car is dead !
Car go to main dealer for repair : car need to change ECU + Dash + keys + gear box management ...
Stupid dealer or very rich client
if dashboard dead, need change just dashboard, not all car electronics

[p1et]

Tested today , now the car is dead !
Car go to main dealer for repair : car need to change ECU + Dash + keys + gear box management ...

How it happened? I thought if you try any tool on this, you just won't connect with dash at all...

[TERMINATOR1000]

it's an joke , if VVDI2 fail , no tool can do it , particular x100pad2 :palm2:

[p1et]

Yup. That video above of xtool working on Polo, it's just old Polo...

[trinicolin]

Hi guys. I attempted to to do all keys lost on BMW F32 with FEM. I made the mistake of removing the eeprom and reading it after backing up the coding, so I got the eeprom data and coding, however I was able to reach the point of rewriting the original eeprom file after 2nd reflash. I am now unable to go further as the fem unresponsive. How do I get around this issue.

Sent from my SM-G930F using Tapatalk

[u.s]

Check the soldering of 95128 chip

[rola1971]

if fem reflash 100% check may be you broke component around eeprom
you doit in the car or i table?
fuse all ok?
5A check fuse in fem

[trinicolin]

if fem reflash 100% check may be you broke component around eeprom
you doit in the car or i table?
fuse all ok?
5A check fuse in femTable

Sent from my SM-G930F using Tapatalk

[trinicolin]

Check the soldering of 95128 chipChecked

Sent from my SM-G930F using Tapatalk

[shotaaa]

734733734734 Guys how to change language to English ?

[immoneard]

734733734734 Guys how to change language to English ?

https://www.digital-kaos.co.uk/forums/showthread.php/717351-VVDI2-Remote-database-change?highlight=VVDI2+remote

[dimm38]

Hello, is there news about new MQB cars & keys?
Nowadays, even cheapest VW Polo uses MQB 5C keys.
As i know, no devices working with them exists. Am i right?

[rola1971]

Hello, is there news about new MQB cars & keys?
Nowadays, even cheapest VW Polo uses MQB 5C keys.
As i know, no devices working with them exists. Am i right?


i make lot of vw mqb keys.i dont know about polo but golf7 no problem

[dimm38]

I think you makes MQB 48 chip, since mid 2020 keys goes with MQB 5C chip. VVDI2 can't recognize them even.

[auto techniek]

I think you makes MQB 48 chip, since mid 2020 keys goes with MQB 5C chip. VVDI2 can't recognize them even.


If vvdi2 does not recognise them then it is MQB2 System

[Maartinj]

if anyone need to contact Support / send feedback - here is quick view how to do that

https://imagizer.imageshack.com/v2/640x480q90/924/uuM3Ey.jpg (https://imageshack.com/i/pouuM3Eyj) https://imagizer.imageshack.com/v2/640x480q90/923/6p0ICg.jpg (https://imageshack.com/i/pn6p0ICgj)https://imagizer.imageshack.com/v2/640x480q90/922/biGSzW.jpg (https://imageshack.com/i/pmbiGSzWj)https://imagizer.imageshack.com/v2/640x480q90/924/WFxMKR.jpg (https://imageshack.com/i/poWFxMKRj)

[obeids]

Hi guys. I attempted to to do all keys lost on BMW F32 with FEM. I made the mistake of removing the eeprom and reading it after backing up the coding, so I got the eeprom data and coding, however I was able to reach the point of rewriting the original eeprom file after 2nd reflash. I am now unable to go further as the fem unresponsive. How do I get around this issue.

Sent from my SM-G930F using Tapatalk

I Had similar issue last week.
I removed eeprom again and wrote file about 10 times and verify also many times. Clean all the pins with fine file. CLean PCB contacts and applu new solder and flux. Then solder back.
Hopefully it will work because mine worked after redo 10 times write file.

[obeids]

Hi there guys.

So I came across a few FEM on BMW where VVDI2 gives the message to Update using BMW E-SYS.
I have the Yellow Ethernet E-SYS cable.
So I would like to confirm if I could make do with the PSDZ Lite files or do we need the PSDZ full files for this job? Is it safe to do on bench?

Also what I see is that VVDI2 is now lacking some Features which their competitors are now supporting. Example read ISN on MSV80 work wonderful on CGDI but VVDI2 say version not supported.
Is Xhorse now forcing us to buy their VVDI BMW tool?
Why not include the function here and gives us full functions of the BMW TOOL? Maybe charge us $200 for the activation and give us the same features here. Why make us buy more hardware for $1000 again?

[u.s]

I did this a while ago when i was just messing about with a spare bdc unit i had.
I think you'll need psdzdata full file but from an earlier release, although vvdi2 says 'update' it actually means downgrade, i did it on the bench.

There's also a newer version of the BMW tool out soon!

[trinicolin]

Hi guys, I need to know the procedure to clone bmw fem.

Sent from my SM-G930F using Tapatalk

[pepi]

Hi there guys.

So I came across a few FEM on BMW where VVDI2 gives the message to Update using BMW E-SYS.
I have the Yellow Ethernet E-SYS cable.
So I would like to confirm if I could make do with the PSDZ Lite files or do we need the PSDZ full files for this job? Is it safe to do on bench?


Also what I see is that VVDI2 is now lacking some Features which their competitors are now supporting. Example read ISN on MSV80 work wonderful on CGDI but VVDI2 say version not supported.
Is Xhorse now forcing us to buy their VVDI BMW tool?
Why not include the function here and gives us full functions of the BMW TOOL? Maybe charge us $200 for the activation and give us the same features here. Why make us buy more hardware for $1000 again?

I had the same issue when VVDI2 did not restore backup coding , I have try many times then it worked.

[marekajs]

I had the same issue when VVDI2 did not restore backup coding , I have try many times then it worked.

dear, if you know svci 2020?

[pepi]

You cant do FEM/BDC with SVCI2020 .

[ttzag]

Hello guys
Any one know where is the problem
While trying to read isn from msv80?https://uploads.tapatalk-cdn.com/20200826/86328aad3ef47fd4e2ac3e3eb769c098.jpg

Sent from my HTC U11 using Tapatalk

[Faraday]

Hello guys
Any one know where is the problem
While trying to read isn from msv80?https://uploads.tapatalk-cdn.com/20200826/86328aad3ef47fd4e2ac3e3eb769c098.jpg

Sent from my HTC U11 using Tapatalk


https://xhorsepolska-download.pl/VVDI%202/

[ypt]

Why not include the function here and gives us full functions of the BMW TOOL? Maybe charge us $200 for the activation and give us the same features here. Why make us buy more hardware for $1000 again?

True...! or some special price for who already have some paid BMW functions active.... who wants to pay 2 times for same on "same" tool? :banghead:

[MACKIE]

Anyone have problem with Small LCD on VVDI2 it just died ...everything other work ok

Regards
Mackie

[dd1]

Hello everyone, i am having with my vvdi2 commander. i wanted to work on a porsche cars, so i purchased the porsche update. now, when i want to make a transponder for a porsche boxster, 2001, i can't. it wont let me. anyone else has this issue?

[iozo]

same on mine , i suspect it stop work on last firmware update . all work fine exept small lcd display
Anyone have problem with Small LCD on VVDI2 it just died ...everything other work ok

Regards
Mackie

[autoTkey]

So who is using this small LCD display anyway?

[Diablotic]

Well...I do...

[pepi]

So who is using this small LCD display anyway?
It is used to show key frequency .

[MACKIE]

same on mine , i suspect it stop work on last firmware update . all work fine exept small lcd display


Did you try to downgrade to test ?

Regards
Mackie

[autoTkey]

OK, I didn't mean to offend anyone :)
For me it is too big and clunky to use for frequency tester. I prefer other tools like KD-X2, KeyTool, CN900mini, China ZedBull, etc...

[szengen]

app xorse ,something wrong that works backwards,
garbage collectors who suddenly make their laws, shit and onions

[szengen]

Anyone can become a representative of xhorse, but probably doesn't want to

[szengen]

if you still want to use the server you must have a xhorce-like phone

[ypt]

It is used to show key frequency .

Mine never worked correctly... Can't read frequency correctly... :(

[ypt]

Delete please

[TERMINATOR1000]

today fail to read immo data 2014Polo 6R , Johnson control NEC 95320 , ID48 no MQB .
i use VAG Helper + 5$ to finish job , it's the first time VVDI2 can't add immo4 key

[comizelu]

Hi,
Anyone succed reading immo data on VW up with mc9s12xhz384 ?
Car it's 2015. Is reading pin,key id but no CS.


Sent from my MI CC9 Pro Premium Edition using Tapatalk

[smokey08]

Hi,
Anyone succed reading immo data on VW up with mc9s12xhz384 ?
Car it's 2015. Is reading pin,key id but no CS.


Sent from my MI CC9 Pro Premium Edition using TapatalkPost the eep and I will give you the key data

Sent from my Pixel 3 using Tapatalk

[comizelu]

here,
thanks

[cjawahir]

vvdi 2 need to repair sw for toyota smart key , even tm100 can do toyota smart , tango old sw can do toyota smart key and now they can do it via obd 2.

remote database need to be fixed to gl version .

cj

[smokey08]

Key 1:


[Page 3/Page 2]
28B85516


[Page 15]
2EE4
[Page 14]
FAB8
[Page 13]
2A51
[Page 12]
1218
[Page 1]
7241
[Page 0]
0012


[Page 9]
75DC
[Page 8]
5213
[Page 7]
FCC1
[Page 6]
102B
[Page 5]
2B93
[Page 4]
9E6E

Key 2:

[Page 3/Page 2]
28B8D0D7


[Page 15]
0FED
[Page 14]
FAB8
[Page 13]
2A51
[Page 12]
1218
[Page 1]
7241
[Page 0]
0012


[Page 9]
75DC
[Page 8]
5213
[Page 7]
FCC1
[Page 6]
102B
[Page 5]
2B93
[Page 4]
9E6E

Write Page 1 last as it locks the chip. I sent the info how to do these dashes to Samic about 10 months ago and its still not added.

Use a cloning chip so you can change the ID (Page 3/Page 2)

[dd1]

Hello everyone, I want to make a key for a Porsche Boxster, 1999. So, I choose Porsche icon then this pops up, this screen comes up. So, how do I make a key for this car? It gives me an error when I open my Porsche eep folder. Any ideas how to fix this

[trinicolin]

In an effort to maintain rating of this tool can we find out whether other tools are having problems with the BMW FEM. I am seeing quite a lot of users are having problems with the VVDI2 and BMW FEM and if in fact there is problem then something needs to be done so as to not to let this issue take away from this tool.

Sent from my SM-G930F using Tapatalk

[K1nd3r]

there is bug if i collect remote tokens by vvdi2, they do not seen in point system, vvdi key tool and vvdi2 merged

[jokir]

Hi
I'm trying to add a new key from VVDI2 XSMQB1EN to the Škoda Superb 2 Kessy. I will prepare it as 202AJ keyleesGo V1 or V2, I will make a deler key (TP24 skoda) and start the learning process.
The first original key 3T0837202K is learned, the second key VVDI2 is attached to the ignition coil, the learning process ends with the message "all keys learned" but on the dashboard the key learning process remains unfinished 1-2 and the new key is not functional.
Where could be the problem ?
Thank you for your feedback.

[optimaplus]

Your second key did not learn remake key or try different key

[ghostrider72]

Did you make ignition on and of before you change keys on learning process?

[jokir]

No, I didn't turn it off and on again before the learning process.
I make a dealer key and started learning the keys, similar to learning passat B8 keys kessy.
I followed the VVDI commander instruction.
It behaves as if it didn't even see the new key

[triak88]

I have the same story with škoda kessy and XHORSE key but I didnt doit sucessly.I order new original key and all OK .Saw something wrong with Xhorse key or procedure of preaper dealer key 100%.

[Maartinj]

For VW they only work if AJ kesy is use (genuine)
Not sure why is that different , perhaps kessy module is older generation
Seems in Skoda could be similar

try with just XS kesy to see if is fully work
if not, you can try replace kessy module to latest one and adapt it

[jokir]

I used the keys:
XSKF01EN and XSMQB1EM
Kessy module:
SW: 5K0 959 434 B HW: 5K0 959 434 (VWKESSYPQ35GP 086 1101)
SW: 5K0 959 434 A HW: 5K0 959 434 A (VWKESSYPQ35GP 085 0802)
He could not learn the key on any of them
Is it possible to update these units?
Datflash offers enough files to upgrade

[sdnatlst]

on Audi Q7, 2012 model, can we do spare key OK via OBD? Or do we still need to remove steering ELV to get the j518 eeprom dump?

thanks all

[titou25]

yes by obd very easy


Envoyé de mon iPhone en utilisant Tapatalk

[alkaskad]

Is there any news about VAG Johnson clusters immo data? I can't find OBD Helper anywhere...

[keymax]

Hello everyone, I want to make a key for a Porsche Boxster, 1999. So, I choose Porsche icon then this pops up, this screen comes up. So, how do I make a key for this car? It gives me an error when I open my Porsche eep folder. Any ideas how to fix this

Ha ha. You think the Porsche button is real. It’s just a reminder of false promises. Just like the pass thru.


Sent from my iPhone using Tapatalk

[qeso705]

For VW they only work if AJ kesy is use (genuine)
Not sure why is that different , perhaps kessy module is older generation
Seems in Skoda could be similar

try with just XS kesy to see if is fully work
if not, you can try replace kessy module to latest one and adapt it

Your advise is to make car compatible with not fully functional remote, not to solve issue with not fully functional remote with pq cars? I misunderstood something or its real solution?

[dd1]

Ha ha. You think the Porsche button is real. It’s just a reminder of false promises. Just like the pass thru.


Sent from my iPhone using Tapatalk
that is strange, so why did they charge me for the porsche authorization????

[dd1]

hello everyone, i have replaced an amplifier on a 2016 porsche 911 and now i have the COMPONENT PROTECTION ACTIVE. I do not know where the original amp is. i have piwis3 and performed coding and programming but nothing. anyone any idea how to get this resolved? the online access is my last option. any other tool that can do this job? thank you in advance

[keymax]

that is strange, so why did they charge me for the porsche authorization????

Bend over and I’ll show you.


Sent from my iPhone using Tapatalk

[cjawahir]

PASSTHRU vvdi2 this not work on techstream w7 and w10 ,

still to date toyota smart dump show dump have 1 key and cannot make key , but tango and tm100 it can do it .

cj

[jokir]

@ comizelu
Try:
AE3B4AC83F8308D4D4C97976

[comizelu]

@ comizelu
Try:
AE3B4AC83F8308D4D4C97976Already tried.
I bought the smok keymaker and program no problems.
Thanks anyway

Sent from my MI CC9 Pro Premium Edition using Tapatalk

[crazylou2017]

Hi there guys.

So I came across a few FEM on BMW where VVDI2 gives the message to Update using BMW E-SYS.
I have the Yellow Ethernet E-SYS cable.
So I would like to confirm if I could make do with the PSDZ Lite files or do we need the PSDZ full files for this job? Is it safe to do on bench?

Also what I see is that VVDI2 is now lacking some Features which their competitors are now supporting. Example read ISN on MSV80 work wonderful on CGDI but VVDI2 say version not supported.
Is Xhorse now forcing us to buy their VVDI BMW tool?
Why not include the function here and gives us full functions of the BMW TOOL? Maybe charge us $200 for the activation and give us the same features here. Why make us buy more hardware for $1000 again?


1. You can try, you don’t need PSDZ files, the VVDI2 software will directly get the missing modules from BMW’s official website when programming and coding.

2. I contacted their engineer and they replied: vvdi2 also needs to be compatible with other car makes. If you need to OBD read ISN without disassembling, VVDI2 is supposed to need to add a new module, so they develop the BIM TOOL PRO. The most important thing for the new device is programming and coding via Ethernet. This plays a very important role in the car maintenance field.
The BMW key programming function of vvdi2 is very similar to that of BIM tool Pro. And the acquisition of ISN generally requires the engine data.

[kristikapa]

1. You can try, you don’t need PSDZ files, the VVDI2 software will directly get the missing modules from BMW’s official website when programming and coding.

2. I contacted their engineer and they replied: vvdi2 also needs to be compatible with other car makes. If you need to OBD read ISN without disassembling, VVDI2 is supposed to need to add a new module, so they develop the BIM TOOL PRO. The most important thing for the new device is programming and coding via Ethernet. This plays a very important role in the car maintenance field.
The BMW key programming function of vvdi2 is very similar to that of BIM tool Pro. And the acquisition of ISN generally requires the engine data.


I remember I was able to read isn from msd80 or msd81 with vvdi2 long time ago. I think it was msd80. So if it's not working anymore most probably they removed it to force buying their new tool. I have vvdi2 and thinking to buy something for bmw but probably I would go with cgdi only because xhorse s discount on their bmw tool for vvdi2 users is a joke. Most of vvdi bmw functions are the same like vvdi2.

[Nymike]

managed to kill cas3 with new xhorse bimtool today. failed during downgrading. never happened to me with cgdi . actually it was the first time I was trying to use this bimtool

[autoTkey]

managed to kill cas3 with new xhorse bimtool today. failed during downgrading. never happened to me with cgdi . actually it was the first time I was trying to use this bimtool

VVDI2 or VVDI BMW blue tool ?

[ypt]

I remember I was able to read isn from msd80 or msd81 with vvdi2 long time ago. I think it was msd80. So if it's not working anymore most probably they removed it to force buying their new tool. I have vvdi2 and thinking to buy something for bmw but probably I would go with cgdi only because xhorse s discount on their bmw tool for vvdi2 users is a joke. Most of vvdi bmw functions are the same like vvdi2.

Same here...

I don't need programming functions... But other tools p.example have egs reset option, have isn read option... Xhorse is forcing users to buy new tool for this...

Even for who has paid for all BMW functions active on vvdi2...
What is supposed to do?

Next year they will launch bimtool evo boing 347 with some other functions?

[sniegavirs]

Depends on what you want to do with your tool. But also keep in mind that VVDI2 and a lot of older Xhorse tools has these promised "Near future" options dragging a long for ages. Since Xhorse is mostly interested in releasing new tools and leaving older ones in the basement i suggest picking newer ones. Plus side of this is that there is one time payment without subscription but that is also a bad thing. If Xhorse wants to keep their company going without subscription model only option is to release newer tools and stopping older tool development. I wanted to add VVDI MB tool to my arsenal but decided to go with Autel IM608 on this. Yes, Autel has yearly subscription around 1000EUR for it but if the development of updates and options keeps coming it is worth it if you actually use the tool. Will see how it plays out in following years.
Conclusion on this is that You yourself has to do the research what is worth buying without subscription model and what isn't. What works and what doesn't. You will never be able to do everything with one tool. Yes there are some good all-a-rounder tools but they are not perfect. Do a research on the options you need and make choices to carve your way to perfection.

[baddaren]

Hello , Anyone else making CAS3+ by OBD with VVDI BMW or VVDI BIM TOOL? Is it safe?Or better on bench? Does the new VVDI BIM TOOL work 100%, read about some problems?? Jakob

[pepi]

Read backup on the bench . You can try after you do backup for furthermore work on downgrade CAS3+.

[baddaren]

Hello , Anyone else making CAS3+ by OBD with VVDI BMW or VVDI BIM TOOL? Is it safe?Or better on bench? Does the new VVDI BIM TOOL work 100%, read about some problems?? Jakob

[sniegavirs]

Hello , Anyone else making CAS3+ by OBD with VVDI BMW or VVDI BIM TOOL? Is it safe?Or better on bench? Does the new VVDI BIM TOOL work 100%, read about some problems?? Jakob
DON'T color your TEXT. It is hard to read it!!!!

[baddaren]

Sorry, Hello, Anyone else making CAS3+ by OBD with VVDI BMW or VVDI BIM TOOL? Is it safe? Or better on bench? Does the new VVDI BIM TOOL work 100%? What is idea buying it if not make KEY by obd? I read about problems with VVDI BIM TOOL! Anyone! Jakob

[danielectronic]

I have audi 8p 2009 eeprom vdo box in service mode and vvdi2 failed to read inmodata any ideas ?
Tengo audi 8p 2009 eeprom vdo box en modo de servicio y vvdi2 no pudo leer inmodata alguna idea?

[rola1971]

problen in you :hmmmm2: brain
read manual

[rola1971]

Sorry, Hello, Anyone else making CAS3+ by OBD with VVDI BMW or VVDI BIM TOOL? Is it safe? Or better on bench? Does the new VVDI BIM TOOL work 100%? What is idea buying it if not make KEY by obd? I read about problems with VVDI BIM TOOL! Anyone! Jakob


any tools dont give you 100% warranty
i have lot of tools but same time 1 car easy next car have problem

[sniegavirs]

Sorry, Hello, Anyone else making CAS3+ by OBD with VVDI BMW or VVDI BIM TOOL? Is it safe? Or better on bench? Does the new VVDI BIM TOOL work 100%? What is idea buying it if not make KEY by obd? I read about problems with VVDI BIM TOOL! Anyone! Jakob
If it's a BMW there is no excuse not pulling it out on the table to make the key with using programmer. And also you will have a full backup of that exact car/cas sw nr. And your own data base collection will grow. That programming part for CAS3+ to be able to add keys through OBD is a tricky move. I have done a lot of CAS3+ units making backup on the table and then doing that programming part on the car with VVDI2 and later some cars have done without the backup. So far I haven't had failed programming. +13V on car with good power supply is a must.
I see this option like this. If you do BMW rarely then take the CAS out and do File Make Key method. Betters safe than sorry. But if you are doing a lot of BMW's with CAS3 units and specially have big data base with backed up cas3 modules, have tools to read ECU's to get ISN and even if you have and know how to use WinKFP and NCS and when/if programming keys through OBD goes bad you can get out of that situation easy than go for OBD key programming. Saves some time if all goes well.
It all depends on You if you want to risk it doing OBD way saving some time or F@@ing up your day or doing it bench/BDM while drinking a coffee. A MINI is a bit different story.. :D

[comizelu]

If it's a BMW there is no excuse not pulling it out on the table to make the key with using programmer. And also you will have a full backup of that exact car/cas sw nr. And your own data base collection will grow. That programming part for CAS3+ to be able to add keys through OBD is a tricky move. I have done a lot of CAS3+ units making backup on the table and then doing that programming part on the car with VVDI2 and later some cars have done without the backup. So far I haven't had failed programming. +13V on car with good power supply is a must.
I see this option like this. If you do BMW rarely then take the CAS out and do File Make Key method. Betters safe than sorry. But if you are doing a lot of BMW's with CAS3 units and specially have big data base with backed up cas3 modules, have tools to read ECU's to get ISN and even if you have and know how to use WinKFP and NCS and when/if programming keys through OBD goes bad you can get out of that situation easy than go for OBD key programming. Saves some time if all goes well.
It all depends on You if you want to risk it doing OBD way saving some time or F@@ing up your day or doing it bench/BDM while drinking a coffee. A MINI is a bit different story.. :DMany locksmiths want to do everything by obd..if something has to come off from the car they like [emoji33][emoji33] and [emoji125][emoji125]

Sent from my MI CC9 Pro Premium Edition using Tapatalk

[sniegavirs]

Many locksmiths want to do everything by obd..if something has to come off from the car they like [emoji33][emoji33] and [emoji125][emoji125]

Sent from my MI CC9 Pro Premium Edition using Tapatalk
If that is the case then that is not a locksmith but a brainless button pusher..

[kristikapa]

If it's a BMW there is no excuse not pulling it out on the table to make the key with using programmer. And also you will have a full backup of that exact car/cas sw nr. And your own data base collection will grow. That programming part for CAS3+ to be able to add keys through OBD is a tricky move. I have done a lot of CAS3+ units making backup on the table and then doing that programming part on the car with VVDI2 and later some cars have done without the backup. So far I haven't had failed programming. +13V on car with good power supply is a must.
I see this option like this. If you do BMW rarely then take the CAS out and do File Make Key method. Betters safe than sorry. But if you are doing a lot of BMW's with CAS3 units and specially have big data base with backed up cas3 modules, have tools to read ECU's to get ISN and even if you have and know how to use WinKFP and NCS and when/if programming keys through OBD goes bad you can get out of that situation easy than go for OBD key programming. Saves some time if all goes well.
It all depends on You if you want to risk it doing OBD way saving some time or F@@ing up your day or doing it bench/BDM while drinking a coffee. A MINI is a bit different story.. :D



Very good answer. Mini is another story :))

[K1nd3r]

what new in 6.8.0 version?

[ch_vladimir]

what new in 6.8.0 version?
where did you find program 6.8.0

this is one

[autoTkey]

Maybe it fixes the clicking (killing) problems with FEM/BDC ?
758681

[sniegavirs]

Maybe it fixes the clicking (killing) problems with FEM/BDC ?
758681
Just did one FEM with older version without problems. How did you killed one?
I definitely cannot recommend using any kind of adapter that suggests you can skip desoldering that eeprom. VVDI Prog, Autel XP400 Pro, Orange5 cannot read it on PCB. It reads it partialy. Only option is to desolder end read ir straight in the programmer. Maybe this is the reason for some people of killing the FEM modules.
Knock on the wood - I haven't had any problems of VVDI2 working on FEM/BDC modules.

[Diablotic]

I definitely cannot recommend using any kind of adapter that suggests you can skip desoldering that eeprom. VVDI Prog, Autel XP400 Pro, Orange5 cannot read it on PCB. It reads it partialy. Only option is to desolder end read ir straight in the programmer.

I disagree. Been using VVDI adapter to read FEM eeprom for over 20 times now and had not single problem. Anyways I also agree that desoldering is safer.

[rola1971]

Maybe it fixes the clicking (killing) problems with FEM/BDC ?
758681


i dont know in any next country cars but i make around 70-100 cars fem and bdm lost and spare key but dont have any problem

[rola1971]

Just did one FEM with older version without problems. How did you killed one?
I definitely cannot recommend using any kind of adapter that suggests you can skip desoldering that eeprom. VVDI Prog, Autel XP400 Pro, Orange5 cannot read it on PCB. It reads it partialy. Only option is to desolder end read ir straight in the programmer. Maybe this is the reason for some people of killing the FEM modules.
Knock on the wood - I haven't had any problems of VVDI2 working on FEM/BDC modules.


i all time read eeprom in pcb used orange5 orginal any problem,i killing when i tray take out eeprom from pcb and broke eeprom but it is maybe 3 year back when fem only start in vvdi2
this moment read only in pcb and dont have problem need only very good clean contact

[p1et]

i killing when i tray take out eeprom from pcb and broke eeprom

What do you mean by broke eeprom? You could not read it after desoldering or data got corrupt because of overheating or maybe you broke some eeprom leg?

I'm just trying to find out what causes problems to people who desolder this eeprom from FEM. I don't understand what differ this eeprom chip from the others that people keeps killing them.

[rola1971]

What do you mean by broke eeprom? You could not read it after desoldering or data got corrupt because of overheating or maybe you broke some eeprom leg?

I'm just trying to find out what causes problems to people who desolder this eeprom from FEM. I don't understand what differ this eeprom chip from the others that people keeps killing them.


it is broke eeprom when tray take out from pcb.very big glue in pcb and when heating i broke legs

it is first fem after and dont take out

[autoTkey]

Just did one FEM with older version without problems. How did you killed one?
I definitely cannot recommend using any kind of adapter that suggests you can skip desoldering that eeprom. VVDI Prog, Autel XP400 Pro, Orange5 cannot read it on PCB. It reads it partialy. Only option is to desolder end read ir straight in the programmer. Maybe this is the reason for some people of killing the FEM modules.
Knock on the wood - I haven't had any problems of VVDI2 working on FEM/BDC modules.

Thanks mate, but it's not me. I read about it in this thread:
https://www.digital-kaos.co.uk/forums/showthread.php/726210-BMW-ALL-FEM-BDC-Full-Soluction/page2

[castin]

Guys. Im need buy BMW key tool. What is better option: VVDI BMW Pro blue or CGDI BMW Full?

[rob h]

Xhorse Bim tool

[danielectronic]

adapt cluster vdo audi 8p 2008 is possible with vvdi2 tool ??

[autoTkey]

Xhorse Bim tool

Not so sure about that. They release new BIM tools like it's car tires - new model each year.

[comizelu]

adapt cluster vdo audi 8p 2008 is possible with vvdi2 tool ??Yes, easy job.

Sent from my MI CC9 Pro Premium Edition using Tapatalk

[castin]

I need a tool for FEM. I have VVDI2 Full. An option for ISN ECU would be useful. I don't know now whether to take FEM license for VVDI2, buy VVDI BIM Tool or CGDI BMW.

[Maartinj]

2020-11-05
Require firmware V6.8.0

>>>DOWNLOAD<<< (https://mega.nz/file/EItBnI6S#Pjdf7SBbD5OqE9s7J96vcA_cNUF2Pxro9VIv0Yyje SE)



!!!This version require update firmware V6.8.0!!!

===== VAG V6.8.0 =====
1. Improvement for autodetect VAG immobilizer system
2. Support Update/Unlock 8E electronic remote(A6/Q7 J518)
3. Bugfix

===== BMW V6.8.0 =====
1. Improvement for FEM/BDC key learning
2. Bugfix

===== Porsche V6.8.0 =====
1. Bugfix

===== PSA V6.8.0 =====
1. Bugfix

===== Transponder Programmer V6.8.0 =====
1. Improvement for make remote
2. Immobilizer data tool:Asia->Ssangyong->Actyon->Diesel-9S12(DST80) bugfix
3. Bugfix

===== Copy 48 (96 bits) V6.8.0 =====
1. Bugfix

===== J2534 V6.8.0 =====
1. Bugfix

===== Online Upate Tool V6.8.0 =====
1. Bugfix

===== Quick Start V6.8.0 =====
1. Bugfix

[autoTkey]

This is old news, mate. It is available since last week and was already discussed here.

[torero233]

few news, little by little it does not update anything

[Maartinj]

This is old news, mate. It is available since last week and was already discussed here.

Just post dectription with link, because some people update frimware and cant download software

[nikovali]

I have installed the update vvdi2 6.8, I installed it many times because the program did not start after installation.Today I tried go program new key for E90/CAS2. Everythi started good Cennect-Get key info and than I got Security Login failed than the car is not starting, ESL is not working and there is an red steering wheel light on the dash, I have not managed to learn a new key to this car, before I did not have this kind of problems, I triend vvdi2 on another car and I get the same results.Now I will have to restore the old version of the software that worked perfect.

Does anybody else have this problem with version 6.8.0 and how can I fix this problem

[sniegavirs]

I have installed the update vvdi2 6.8, I installed it many times because the program did not start after installation.Today I tried go program new key for E90/CAS2. Everythi started good Cennect-Get key info and than I got Security Login failed than the car is not starting, ESL is not working and there is an red steering wheel light on the dash, I have not managed to learn a new key to this car, before I did not have this kind of problems, I triend vvdi2 on another car and I get the same results.Now I will have to restore the old version of the software that worked perfect.

Does anybody else have this problem with version 6.8.0 and how can I fix this problemWhen you pushed GET KEY INFO did you removed the key from the key slot when it asked you to???
Did one E60 CAS2 today without problems. But for E90 red steering simbol you need to do CAS/ELV sync and all will be ok.

[nikovali]

When you log in to GET KEY INFO you get the original working key.
I want to be given information about the keys in CAS.
After I locked vvdi2 and followed a few attempts to put the keys in the locks, the handle and the car were unlocked and started.
Drugata kola na koja probav da napravam kljuc bese 118 / CAS2 / 2006.
With the previous versions of the program, there are about 20 keys without any problems

[castin]

When you pushed GET KEY INFO did you removed the key from the key slot when it asked you to???
Did one E60 CAS2 today without problems. But for E90 red steering simbol you need to do CAS/ELV sync and all will be ok.
Whem i hawe this, then after 5-7 times motor on, motor off this mesage go off.

[TERMINATOR1000]

Whem i hawe this, then after 5-7 times motor on, motor off this mesage go off.

yes , i confirm that , same case last week with CGDI BMW on 2006 E91 CAS3. certainly defective ELV , lost of com between CAS / ELV . Sync failed by OBD2

[nikovali]

yes , i confirm that , same case last week with CGDI BMW on 2006 E91 CAS3. certainly defective ELV , lost of com between CAS / ELV . Sync failed by OBD2


How did you solve the problem with synchronization?

[habbyb]

hello everyone , someone worked for Toyota Europa 8A all key lost with adapter xhorse 8A AKL toyota , I'm telling it doesn't work , work only asian toyota .

[Jimmy07]

Doesn’t work piece of crap

[habbyb]

AVDI is super one .

[darknezz19]

2017 Evoque KVM, FK72-19H440. Hit reset sec button. Not sure if this is saying it was never secured to begin with or is now unsecured.


[2020-11-21 12:04:19] : Select <Reset Sec>
[2020-11-21 12:04:19] : Check Device...
[2020-11-21 12:04:20] : 12V Power Adaptor unconnected
[2020-11-21 12:04:20] : Initialization device...
[2020-11-21 12:04:24] : Initialization success!
[2020-11-21 12:04:25] : Initialization chip...
[2020-11-21 12:04:25] : ID 0M12S 0XC483/1M12S 0XC483
[2020-11-21 12:04:25] : Backup the <8-OTHER_LANDROVER_RFA-SECURED(MC9S12XEQ384)> Reset Sec operation security area data in file: 20201121_120425_8-OTHER_LANDROVER_RFA-SECURED(MC9S12XEQ384)_backup_data.bin
[2020-11-21 12:04:25] : Start communication...
[2020-11-21 12:04:25] : Chip is not crypt FE
[2020-11-21 12:04:25] : End communication...
[2020-11-21 12:04:25] : Operation success

Edit: if anyone else was thrown off by the log it's saying chip was unlocked here. Flashed new files from VVDI2 and set sec byte to FE, then reset sec byte again and log was the same as above.

Edit: my mistake, forgot there was a vvdi prog thread in Immo sub forum:(

[sniegavirs]

2017 Evoque KVM, FK72-19H440. Hit reset sec button. Not sure if this is saying it was never secured to begin with or is now unsecured.



Edit: if anyone else was thrown off by the log it's saying chip was unlocked here. Flashed new files from VVDI2 and set sec byte to FE, then reset sec byte again and log was the same as above.
This thread is about VVDI2 not VVDI Prog

[Diablotic]

Version 6.8.1 released - supports MQB/5C

[ghostrider72]

Yeah. Tested last week. Works dude [emoji38]

[ladadens1]

immo 5c with vvdi2 works obd when got working key?

[auto techniek]

you need immo data. VVDI2 can t get immo data.
If you are lucky vagobd helper can do the job

Yesterday tried 2020 Seat Ibiza without luck

[ladadens1]

need immo data for akl.but when got working key think dont need anything

[darknezz19]

2013 Boxster with BCM mcu 5m48h OBD key learn with dump success. Read p and d flash okay with backup option, but with unlock option chip would return FFFF ID, so felt sketchy trying to write new dump with force unlock option.

[PerryZhang]

2013 Boxster with BCM mcu 5m48h OBD key learn with dump success. Read p and d flash okay with backup option, but with unlock option chip would return FFFF ID, so felt sketchy trying to write new dump with force unlock option.
Yes, you are right, need to force unlock and write back lock again

[darknezz19]

Okay, I'll remember that.

[PerryZhang]

Okay, I'll remember that.
Don't forget enter security code byte as 7D

[nikovali]

Today I worked on BMW E91/ 2006 AKL, i used VVDI2 to add new key and it worked fine, the car started all good but ESL error showed on the display.


The car worked for couple of hours and than it is not starting any more. I tried to reset ESL counter with Rheingold but it is not letting me reset ESL.


I am planning to try VVDI option Sync CAS-ESL tommorrow, also car battery is unpluged tonight.


Any suggestions and advice are most welcome, thanks in advance.


Any suggestions

[ttzag]

Today I worked on BMW E91/ 2006 AKL, i used VVDI2 to add new key and it worked fine, the car started all good but ESL error showed on the display.


The car worked for couple of hours and than it is not starting any more. I tried to reset ESL counter with Rheingold but it is not letting me reset ESL.


I am planning to try VVDI option Sync CAS-ESL tommorrow, also car battery is unpluged tonight.


Any suggestions and advice are most welcome, thanks in advance.


Any suggestions

for cas 2 white its better to backup on table before obd
try to reset esl by launch if you have

[nikovali]

for cas 2 white its better to backup on table before obd
try to reset esl by launch if you have


The car is with CAS3/3+, I don’t have backup and also don’t have Launch, I have available BMW Explorer chinese clone.

[danis11]

Today I worked on BMW E91/ 2006 AKL, i used VVDI2 to add new key and it worked fine, the car started all good but ESL error showed on the display.


The car worked for couple of hours and than it is not starting any more. I tried to reset ESL counter with Rheingold but it is not letting me reset ESL.


I am planning to try VVDI option Sync CAS-ESL tommorrow, also car battery is unpluged tonight.


Any suggestions and advice are most welcome, thanks in advance.


Any suggestions
It`s ok. You need sync cas-esl after add key with vvdi or avdi. ...may by also sync cas-dde.

[nikovali]

I left the car with unplugged battery overnight. In the morning I did sync CAS-ELV, it was succesful on second attempt.
Everything is working good not. Thanks everyone!!

[trinicolin]

hi Guys, i attempted to add key BMW CAS3++ISTAP and got this message. I removed CAS and backed up the data, eeprom and flash. i added key by dump then replaced CAS to car and start with both original and added key. Remote worked fine however when i tried to add comfort access by OBD i got the same message. My question is " Is there anything wrong with the CAS ?'

[ASCM]

hi Guys, i attempted to add key BMW CAS3++ISTAP and got this message. I removed CAS and backed up the data, eeprom and flash. i added key by dump then replaced CAS to car and start with both original and added key. Remote worked fine however when i tried to add comfort access by OBD i got the same message. My question is " Is there anything wrong with the CAS ?'If you maked backup d and p data
Downgrade cas now and add key by obd

Sent from my 5033F using Tapatalk

[trinicolin]

If you maked backup d and p data
Downgrade cas now and add key by obd

Sent from my 5033F using TapatalkI attempted to add comfort access where I still have to downgrade, and corrupted the cas. I rewrite both eeprom and flash and got it going again. Is that this car would have to do without the comfort access?

Sent from my SM-G930F using Tapatalk

[auto techniek]

Guys

Always the same problem with MM7 cluster VW up 2016

Can't read CS. I did clone the transponder.



https://uploads.tapatalk-cdn.com/20210102/e82fa6de67a695c24661cac5b1d9ace2.jpg

[ramboguy2008]

yes , it does need isn , if all key lost , you need to get the isn from ecu
even if the cas is cas4 not cas4+ ? i think you dont need isn if cas is normal cas4 not the + version

[ladadens1]

always need isn when akl situation.

[comizelu]

always need isn when akl situation.Not always..

Sent from my MI CC9 Pro Premium Edition using Tapatalk

[auto techniek]

When is isn not needed then?


Not always..

Sent from my MI CC9 Pro Premium Edition using Tapatalk

[rob h]

Avdi and Smok do these.
Did one akl, and needed to use Avdi and vvdiprog.

Good that vvdi2 shows a popup warning, not to proceed with programming.


Guys

Always the same problem with MM7 cluster VW up 2016

Can't read CS. I did clone the transponder.



https://uploads.tapatalk-cdn.com/20210102/e82fa6de67a695c24661cac5b1d9ace2.jpg

[comizelu]

Avdi and Smok do these.
Did one akl, and needed to use Avdi and vvdiprog.

Good that vvdi2 shows a popup warning, not to proceed with programming.Smok xcan and keymaker works perfect.
Also learn key by obd,no problems.

Sent from my MI CC9 Pro Premium Edition using Tapatalk

[PerryZhang]

let me upload that issue to xhorse R&D team , let them know it ,to see if can improve in future

[smokey08]

let me upload that issue to xhorse R&D team , let them know it ,to see if can improve in futurePrivate message me your email address, I sent the data to samic to add this function about a year ago.

Sent from my Pixel 3 using Tapatalk

[PerryZhang]

************************************************** **********************
*** 2021-01-05
*** Require firmware V6.8.1
************************************************** **********************
===== VAG V6.8.2 =====
1. Improvement for MQB/5C key learning
2. Improvement for autodetect VAG immobilizer system
3. Bugfix


===== BMW V6.8.2 =====
1. Bugfix


===== Porsche V6.8.2 =====
1. Bugfix


===== PSA V6.8.2 =====
1. Bugfix


===== Transponder Programmer V6.8.2 =====
1. Support make remote for XM proximite remote
2. Bugfix


===== Copy 48 (96 bits) V6.8.2 =====
1. Bugfix


===== J2534 V6.8.2 =====
1. Bugfix


===== Online Upate Tool V6.8.2 =====
1. Bugfix


===== Quick Start V6.8.2 =====
1. Bugfix


download link : https://public-ap-southeast-1-1251058331.s3-ap-southeast-1.amazonaws.com/download/product/vvdi2/software/VVDI2-InstallerV682.exe

[Alpaholic]

Is it true that vvdi2 make id48 96bit copy free? Do they calculate this only online?

[autoTkey]

Yes, only online like everyone. And no - it's not exactly for free (maybe almost).

[didi_du_93000]

Can read immo data from vw new beetle 2017.

Impossible to make spare key.
Mqb48https://uploads.tapatalk-cdn.com/20210108/3538af82d00fe3125f31cb753758e6ae.jpg

Envoyé de mon LYA-L29 en utilisant Tapatalk

[lock66]

I also could not read the immo date.
VAG Helper couldn't help.

[PerryZhang]

Is it true that vvdi2 make id48 96bit copy free? Do they calculate this only online?
no ,it is not free, you need to use token or points , vvdi 2 calculation online

[keysmith]

What is the procedure to get a BMW out of transport / shipping mode?

"Add special function for F/G series: Reset engine start, switch off transport mode, reset ELV, write SVT, initialize Flexray etc."

[dimet]

no ,it is not free, you need to use token or points , vvdi 2 calculation online

How to use this option?

[offsystem]

i have problem with VAG MQB 5G0920870A i choose 2014+ instead of 2012, it was not possbile to login.

but now i have the problem that the display is BLACK and not working anymore.

any idea how i can fix it ?

reset cluster does not help

[momogsm]

i have problem with VAG MQB 5G0920870A i choose 2014+ instead of 2012, it was not possbile to login.

but now i have the problem that the display is BLACK and not working anymore.

any idea how i can fix it ?

reset cluster does not help
Hi

Still Connection To The Dashboard ? With VVDI2 Or Diagnostic ?

Regards

[catalinosonesti]

i have problem with VAG MQB 5G0920870A i choose 2014+ instead of 2012, it was not possbile to login.

but now i have the problem that the display is BLACK and not working anymore.

any idea how i can fix it ?

reset cluster does not help
Hi
Disconect the batery of the car 10 sec , if is vw golf 7 then work ,but km no change it will be the same ,because the car is not 2014 <
best regrads

[offsystem]

Hi

Still Connection To The Dashboard ? With VVDI2 Or Diagnostic ?

Regardsyes diagnostic is possible, just screen is black , i also disconnected Batterie but not working

Gesendet von meinem SM-G986B mit Tapatalk

[momogsm]

yes diagnostic is possible, just screen is black , i also disconnected Batterie but not working

Gesendet von meinem SM-G986B mit Tapatalk
Hi

If Diagnostic Is Possible Then The Dashboard Is Not Totally Bricked, Then You Still Have Chance To Repair It,

The Car Is Keyless Or No ?

Regards

[offsystem]

Hi

If Diagnostic Is Possible Then The Dashboard Is Not Totally Bricked, Then You Still Have Chance To Repair It,

The Car Is Keyless Or No ?

Regardsnot keyless System

but how to fix this?

Gesendet von meinem SM-G986B mit Tapatalk