VAG-COM/VCDS EVERYTHING

[magadan]

Send me the loader?
I want to present to you a loader for the VCDS11.11.0 program. It should be used for cables in which chip FT232R is used. Loader works for 32-bit to system.

[tracera6]

I want to present to you a loader for the VCDS11.11.0 program. It should be used for cables in which chip FT232R is used. Loader works for 32-bit to system.


Works with 11.11.3?

[mattydr67]

Works with 11.11.3?

Of course not
Good luck

[allnamesused]

Hi every body ,i have had 912 cable for about 2years no problems running 912 software,now i have re installed windows, only to find i have lost the file software 912,,will the file 912 on this forum work with my cable or is it different? (srry to sound a bit dumb just dnt wanna fry cable):hello: thanks. ( rl version)) .................................................. .................................................. .. its ok i managed to find 1 thanks,,can ft232rl be upgraded to 11.11?

[KenshinPT]

can ft232rl be upgraded to 11.11?

Yes. You need the dump and the loader.

Regards

[tazman13]

I have made a mistake, my cable was working fine with loader 11.2 (supplied from here) until i tried to use another version loader. the PID and VID were changed (reprogrammed with EPT file). i have tried 11.2 loader again and now it keeps saying unregistered in red (not the registered green message). I have uninstalled everything i can and reinstalled 11.2 and then over written the EXE with the loader that worked (exactly the same thing i did before when it all worked). when i do a test the cable is seen and all the options are OK (appears good). is it something to do with the EPT file programmed (S/N) or is there a marker somewhere that needs to be removed stopping the loader?

having read a bit more on GF and DK i thinks i have to reprogram atemga, time to upgrade to 11.11

thanks in advance

[tazman13]

I want to present to you a loader for the VCDS11.11.0 program. It should be used for cables in which chip FT232R is used. Loader works for 32-bit to system.

i have reprorammed with 11.11.bin and tried your loader, keeps coming up with wrong version when i run it in the 11.11 directory.

[magadan]

......keeps coming up with wrong version when i run it in the 11.11 directory.
I didn't understand your question. Make an error scrinshot. I badly understand on English.
And what system is set at you on the computer? How many bits?

[Livyu18]

this is a very good topic.
Cheers everybody

[tazman13]

win7 so 64bit

11.2 loader with 11.11 dump (new S/N) works fine.

[mattydr67]

win7 so 64bit

11.2 loader with 11.11 dump (new S/N) works fine.

Mate
Dump for VCDS 11.11.0 of course it is working with all previos versions.
But the Loader made by magdan works just on 32 bits. If you have 64 bits of course it dosen't work.
But the loader made by magadan it is very good if you use tools with FTDI 232 RL
Good luck

[magadan]

win7 so 64bit

11.2 loader with 11.11 dump (new S/N) works fine.
Replace in the folder with the program the vcds.exe file from the 32nd bit system. So it was possible on old versions of the program. Check.
Or send to me the vcds.exe file. I will try to make other loader.

[tazman13]

Here is the EXE file that I have from the 11.11 install.

[yo3]

HI, if my cable has 232BL what ept I use?
Also I don't have 93c46, I flash only the Atmega?
Thank you

[mattydr67]

HI, if my cable has 232BL what ept I use?
Also I don't have 93c46, I flash only the Atmega?
Thank you

If you have FTDI 232 BL or BM in this case you have for sure 93C46 or 93C56 or an equivalent.
Just if you ahve FTDI232RL you haven't an eeprom as 93C46 or 93C56
And yes you have to reflash just the Atmega
FTDI if it is necessary you can flash it by USB using MProg
Good luck

[tr3ce13]

Use instead eXtreme Burner - AVR. It's easier! :)

avrdude -c usbasp -p m162 -euV -U flash:w:Flash_191.hex -U eeprom:w:EEPROM.hex -U lfuse:w:0xcd:m -U hfuse:w:0xdc:m -U efuse:w:0xf9:m -U lock:w:0xcc:m

Thanks but this is faster, one click and programmed :proud:

[tazman13]

Here is the EXE file that I have from the 11.11 install.

was this of any use? i have not used the 1111 file you posted yet.

[magadan]

HI, if my cable has 232BL what ept I use?
Also I don't have 93c46, I flash only the Atmega?
If in your cable is FT232B and isn't present 93?46, then VID-PID will be equal 0403-6001. And the cable will work as com-port. If it not so, 93?46(or 93C56) is present at your cable.
Here dumps for USB-cables are placed. If your cable is calculated for com-port, you should seal 93?46, and then to program MProg.

was this of any use? i have not used the 1111 file you posted yet.
I thought everything it will be simple.
In the 64th bit system of a command of the assembler have other codes, and Olly debager isn't suitable for these programs. At me there is no time to study the 64th bit assembler. Use the 32nd bit file vcds.exe together with a loader.

[tazman13]

does anyone have the 32bit 11.11 with loader? i tried the 11.11 file supplied in this thread but it did not work. i have uninstalled 11.11 now so my 11.2 is not broken.

[ssilvviu]

This is 11.11.0 and his loader.
But do you have a good-working eeprom dump for atmega?

[cocoh]

I use VAG COM 11.11 cable
but I CAN'T delete fault codes from AirBag..

any solution?
firmware its 1.84

[mattydr67]

I use VAG COM 11.11 cable
but I CAN'T delete fault codes from AirBag..

any solution?
firmware its 1.84

If your tool is good, I mean it is full Activated/Registred maybe you need to see what exaclly DTC you have and use the solution to fix that issues. Then you'll be able to erase the DTC
If you have Crash Data DTC don't use the VCDS becasue it is not usefull and you waist your time with it.
Good luck

[magadan]

does anyone have the 32bit 11.11 with loader? i tried the 11.11 file supplied in this thread but it did not work. i have uninstalled 11.11 now so my 11.2 is not broken.
Install the program on the system. Backup the file vcds.exe 64th bit (rename). Place in the folder with the program the file vcds.exe the 32nd bit and the file of a loader. Launch the program from a loader (not from the file vcds).

[tazman13]

This is 11.11.0 and his loader.
But do you have a good-working eeprom dump for atmega?

yes my atmega has been flashed with new 11.11 1.84

will try these files.

[cocoh]

If your tool is good, I mean it is full Activated/Registred maybe you need to see what exaclly DTC you have and use the solution to fix that issues. Then you'll be able to erase the DTC
If you have Crash Data DTC don't use the VCDS becasue it is not usefull and you waist your time with it.
Good luck

I gave the error related to the license
seems Was NOT full Activated/Registred
the airbag was changed,
I had only to identify and delete errors
now i installed 11.11.2 i'll try again..

thnk you

[mattydr67]

I gave the error related to the license
seems Was NOT full Activated/Registred
the airbag was changed,
I had only to identify and delete errors
now i installed 11.11.2 i'll try again..

thnk you

Mate the dump from your VCDS 11.11.0 will be blacklisted in the new version for sure.
So in your case it very simple, you need to reflash your toll first then it will work
Don't waist your time
Good luck

[tazman13]

Install the program on the system. Backup the file vcds.exe 64th bit (rename). Place in the folder with the program the file vcds.exe the 32nd bit and the file of a loader. Launch the program from a loader (not from the file vcds).

worked perfect :shakehands:

[liviudiaconu]

I
the airbag was changed,
I had only to identify and delete errors


Airbag was replaced but the "crash data" from airbag controler was deleted? Cannot delete with VCDS. Or, airbag controler was replaced too? If not, must erase crash data. If yes, why have errors?

[iustin73]

Where can I find driver for 11.11 VCDs? What you posted does not contain drivers for the cable.

[mattydr67]

Where can I find driver for 11.11 VCDs? What you posted does not contain drivers for the cable.

Mate all VCDS installers, no metter what version item are, the drivers it is installed in the same time with softwear.
So the drivers it is conetent into the VCDS folder where it is installed ( as C:\Ross-Tech\VCDS ) and it is called RT-USB.inf
You can brows to this folder if you cannot install drivers automatically
Good luck and enjoy

[Alexu Alex]

salut ma po-ti ajuta ,am vcds nu pot sai sciu atmg 162 .il citesc dar nul pot sterge ,sau sal scriu multumesc

[mattydr67]

salut ma po-ti ajuta ,am vcds nu pot sai sciu atmg 162 .il citesc dar nul pot sterge ,sau sal scriu multumesc

First of all into the forum you have to write in English and if you like to speack your language you can do it using PM
And second you cannot read teh Atmega becasue it is write protected, then maybe you maybe did a mistake that's why you cannot reflash it. Or in the wirst case the Atmega it is blocked
Who knows.
We will see. But first share two pics of your both sides of your interface PCB
Good luck

[ssilvviu]

He can't write in his native language, do you think he can do it in English?

[mattydr67]

Hahahaha...... He can't write in his native language and he can't "write" ( reflash Atmega ) too.
What a coincidence? Don't you think?
Have a nice day.
Good luck

[j4g3d]

Guys, i have 10.6 cable. Always die on me and sometime lucky to repair by spending hours on it. Sometime not able to.

Is there a good repair guide on here?

Any alternative software version more stable that we can use on this cable?

[zakdk]

hi guys where can i buy a clone of these?

[coraaa]

On which date the dump for version 11.11.0 was released?
Maybe any forecast when the next version will be released?

[mattydr67]

On which date the dump for version 11.11.0 was released?
Maybe any forecast when the next version will be released?

The dump like this it is very hard to extract becasue you need an old genuine tool with BM for this.
This kind of tools are very hard to find.
So I belive a new dump like this will show up in a year or never
Good luck

[wiski]

I have tried to read all thread and not bother you guys with silly questions. Just need confirmation that these is hardware prob and not reflash related.
I have 11.11 which get hotter from beggining , it worked fine for a month Yes it become unregistred in soft.Ftdi is BL.
I replaced 7805 same thing.

[mattydr67]

I have tried to read all thread and not bother you guys with silly questions. Just need confirmation that these is hardware prob and not reflash related.
I have 11.11 which get hotter from beggining , it worked fine for a month Yes it become unregistred in soft.Ftdi is BL.
I replaced 7805 same thing.

Why replaced 7805 beacasue your tool becmes unregistred?
You have to reflash the Atemega if it becomes unregistred no need to replaced the 7805.
Good luck

[wiski]

I have missed the concept of my problem while trying to explain. My main problem is that 7805 is getting pretty hot. Led is green.Thank you for reply

Sent from my GT-I9100 using Tapatalk

[mishu_b]

I have missed the concept of my problem while trying to explain. My main problem is that 7805 is getting pretty hot. Led is green.Thank you for reply

Sent from my GT-I9100 using Tapatalk


don't worry about it - it is normal to be hot, in fact the power dissipation of it is quite high.

KR

[wiski]

Thanks. I have other good stable 805 it does'nt heat up like this one . Quality of components probably.

Sent from my GT-I9100 using Tapatalk

[mattydr67]

Thanks. I have other good stable 805 it does'nt heat up like this one . Quality of components probably.

Sent from my GT-I9100 using Tapatalk

Of course in chinese tools you have low quallity components for sure.
But mishu_b has right too
Good luck

[iustin73]

hello guys please how can you not have refresh groups measured values ***8203;***8203;is very slow reading speed values ***8203;***8203;at 11.11 VCDs

[pomarada]

Hello
First, sorry for my English, I use an online translator

After reading the whole thread, there are things I do not clarified by the translator and I get lost with it.

If someone can answer me in Spanish by mp thank you and if you can not be, I will try not to be very wrong with the translation.

I have a cable Chinese clone with version 11.8 use the perfect 11.2 in, and I want to upgrade to 11.11.0.
download the Dump 11.11.0 of this forum, I have a USBisp, ponyprog, extreme burner, also mprog you have some photos of my clone.
It does not look very good, but it FTDI232BM, atmega 162 but change this 93C46 , mine is 93c56w6

I've looked at the tutorial on this forum and although I have some doubt with the dump files to choose and not find a way to connect the cables to the programmer
Are these photo 4?

In the dump, are 6 files.
- 93C46 ---------- Required?
- Dump ---------- ?ATMEGA?
- TT232Bm ------ FTDI
- FT232RL ---------- FTDI
- Installer ------

The first thing you need to know is:
* What if you can upgrade?

regards

[liviudiaconu]

T5, R50, IC8 = DESOLDER, ELIMINATE forever..
(20120730_120032.jpg (2 of 4)

must write this:
atmega dump (if your cable work with another VCDS soft).

install 11.11.0 (installer).

FT232BM dump or 93C46 dumps (is the same thing but with 2 different method) are needed if your VCDS cable was broken by another VCDS soft or internet.
For write FT232BM dump you need MProg 2.8 or 3.5 too (from FTDI)

[zakdk]

hi can someone pm me a good place to buy a chinese cable..

[pomarada]

T5, R50, IC8 = DESOLDER, ELIMINATE forever..
(20120730_120032.jpg (2 of 4)

must write this:
atmega dump (if your cable work with another VCDS soft).

install 11.11.0 (installer).

FT232BM dump or 93C46 dumps (is the same thing but with 2 different method) are needed if your VCDS cable was broken by another VCDS soft or internet.
For write FT232BM dump you need MProg 2.8 or 3.5 too (from FTDI)

Ok
Thank you for your answer.
* Then, as the cable now works well with 11.2, not be installing the ftdi or 93

Will eliminate the components that you say, and installing it Atmega dump only.

greetings and thanks again

[mattydr67]

Ok
Thank you for your answer.
* Then, as the cable now works well with 11.2, not be installing the ftdi or 93

Will eliminate the components that you say, and installing it Atmega dump only.

greetings and thanks again

Mate in your tool remove the components indicated the liviudiaconu and the reflash the Atmega with dump for VCDS 11.11.0
After this you'll be able to use the origianl VCDS 11.11.0 softwear.
FTDI can be flashe by USB no need to flash the 93C46.
Good luck

[pomarada]

Mate in your tool remove the components indicated the liviudiaconu and the reflash the Atmega with dump for VCDS 11.11.0
After this you'll be able to use the origianl VCDS 11.11.0 softwear.
FTDI can be flashe by USB no need to flash the 93C46.
Good luck

thanks
- But the ftdi not need to reprogram, to work fine now.
* Right?
Or, to reprogram Atmega with 11.11.0 is needed, reprogram ftdi?

greetings and thanks

[KenshinPT]

thanks
- But the ftdi not need to reprogram, to work fine now.
* Right?
Or, to reprogram Atmega with 11.11.0 is needed, reprogram ftdi?

greetings and thanks

In fact you're not programming the FTDI... you're programming the external FTDI's EEPROM (93C46).

And to answer your question you only need the reprogram the compromised ICs.

That is: if the 93C46 is compromised, you need to reflash it. The same applies to the ATMEGA.

If you are not sure, reflash both.

Good luck

[mattydr67]

thanks
- But the ftdi not need to reprogram, to work fine now.
* Right?
Or, to reprogram Atmega with 11.11.0 is needed, reprogram ftdi?

greetings and thanks

Mate FTDI must be reflashed just if it is not recognized as Ross-tech hex can into the Device Manager.
Other wise why shoild you need to reflash it?
The dump for FTDI that ept file ( it is the same for any version )
You need to reflash it if your tool was erased and the tool it is not recognized into the Devicer Manager or it is showing to you FFFFFFFFF or other VID/PID then 0403/FA20 ( for FTDI BL/BM ) or FA24 ( for FTDI RL )
So if your tool it is recognized and it is not erased and you need just to update it then you have to unsolder that component indicated by the liviudiaconu and reflash the Atmega.
Good luck

[alin 151]

..........................

[mladen76]

if i have cable with FT232RL ,fw184 and software 11.2.0, i can try 11.11.0 version?

NO,just use version you have,DO NOT TRY other versions of program and DO NOT use internet on laptop you have installed Vcds program to be shoure you don't "kill it"

[mattydr67]

if i have cable with FT232RL ,fw184 and software 11.2.0, i can try 11.11.0 version?

Alin
You can use just version you have.
For other upgraded versions you need to reflash Atmega.
I can't see well so please tell me what kind of FTDI you've got?
Is it FTDI BL or RL?
Thanks
Good luck

[perotok]

if i have cable with FT232RL ,fw184 and software 11.2.0, i can try 11.11.0 version?

Alin

If you have cable RL (11.2)
you can upgrade your cable to version 11.11.0 like Matty says
(flash Atmega)
But you must have loader for version 11.11.0

Good luck

[alin 151]

..........................

[alin 151]

..........................

[bibkare]

I found it!
Dump from page 195 posted by DaniXDX. (http://www.digital-kaos.co.uk/forums/members/131153-danixdx/)
Thanks everyone.
Now, my cable works with 11.11.0

Do you use it with loader for 11.11.0 or without ? From my experience you can use RL interface without loader only 3 times before breaks down.

[alin 151]

..........................

[alin 151]

..........................

[ana_11]

Hi

I have VCDS 11.11.0 and have problem, unregistered version.
What i need reprogram and need bin file.

Thx

[alin 151]

..........................

[perotok]

Hi

I have VCDS 11.11.0 and have problem, unregistered version.
What i need reprogram and need bin file.

Thx

Hi

You must upgrade Atmega with 11.11.0 dump
Flash Atmega (flash + eeprom) with external programmer
and flash FTDI with Mprog over USB (ept file)

If you have BL cable then it is easier (only flash atmega and FTDI)

but if you have RL cable you must unsolder a few components and then flash atmega

For RL cables you must use loader

Good luck

[alin 151]

..........................

[mattydr67]

This is another cable 10.6 with BL ftdi which
works ok with 11.11.0

Alin ecusme but can you tell me why did you solder that 4 whire wires?
I belive that wires are for reflashing Atmega, am I right?
If it is so I can tell you that you do not need to solder any wires if you like to reflash that kind of tool.
Good luck

[alin 151]

..........................

[mattydr67]

You're right

I created a permanent connection that allows me to rewrite ATMEGA at anytime

What do you mean?
I do not know another way to rewrite ATMEGA


Good luck!

Thanks
It is what I belived.
But as I told you. You don't need to solder that wire if you want to reflash the Atmega.
In that way
That kind of tools have reflashing pads near the USB once and you can use item.
Well you can solder there wires to reflah the Atemga.
Or you cannot solder any wires if you like.
Take a look
Good luck

[alin 151]

..........................

[pomarada]

This is another cable 10.6 with BL ftdi which
works ok with 11.11.0


Thanks
It is what I belived.
But as I told you. You don't need to solder that wire if you want to reflash the Atmega.
In that way
That kind of tools have reflashing pads near the USB once and you can use item.
Well you can solder there wires to reflah the Atemga.
Or you cannot solder any wires if you like.
Take a look
Good luck

Hello
solder seem easier, in this model of motherboard.
Can you tell me where I buy and if BL BM?

regards

[ana_11]

Try this.
This is what i just used for 11.11.0
Its from page 195 but was deleted!


OK thx, Tomorrow I will try and post result ;)

[ana_11]

I open my interface and I see eeprom 93c56 not 93c46
and ftdi 232BL

Any help ?

[mishu_b]

I open my interface and I see eeprom 93c56 not 93c46
and ftdi 232BL

Any help ?

...
use Mprog for 93cxx - it doesn't care what do you have inside!

step by step.

1. open the case of the tool (VAG tool)
2. solder 4 to the Atmega162 MOSI, MISO, SCK, RESET
3. supply the Atmega with 5V
4. erase the Atmega162
5. Set-up the fuse & security bytes
6. write FLASH and EEPROM into Atmega 162
7. desolder the 4 wires soldered above
8. plug the USB cable into USB port
9. with Mprog - read & purse
10. open the .ept file
11. write into 93Cxx via FTDI
12. install the proper version of the sw (according to the Flash and Eeprom written in)
14. be happy

KR

[KenshinPT]

I open my interface and I see eeprom 93c56 not 93c46
and ftdi 232BL

Any help ?

You don't need any help :)

The 96x56 has twice the capacity of the 93x46 and you don't need to do anything special to reflash this kind of memory.

Good luck.

[wiski]

...

10. open the .ept file (fdti ept right?)
11. write into 93Cxx via FTDI (after opening ftdi ept file, which command exactly?)

KR

Could you please clear it up for me. After opening ftdi ept file and after writing it should the 93cxx file renamed as .ept ?

[alin 151]

..........................

[wiski]

I now how to program ftdi. What I don't understand is how to flash 93c with mprog. I have bin file for 93c

So first i program ftdi with it's ept file and recycle it ,then what , how to open 93c file?

[alin 151]

..........................

[wiski]

Ok thanks , i thought that i'm missing a part here. Anyway i had flashed atmega (write and verified OK) but i have blinking red led. Cable shows ok on hardware devices but when connected to car with it shows not connected to car. Tried different 11.11 atmega file but with same error

[alin 151]

..........................

[alin 151]

..........................

[mattydr67]

I now how to program ftdi. What I don't understand is how to flash 93c with mprog. I have bin file for 93c

So first i program ftdi with it's ept file and recycle it ,then what , how to open 93c file?

Mate
The bin file is for the eeprom when you flash it using an external programmer.
If you use MProg using USB connectio true FTDI you need the ept file.
So it is your choice. If you like to reflash the 93Cxx true USB you can use MProg.
If you like to reflash the 93Cxx directlly with an extrernal programmer you need the bin file
Good luck

[perotok]

I now how to program ftdi. What I don't understand is how to flash 93c with mprog. I have bin file for 93c

So first i program ftdi with it's ept file and recycle it ,then what , how to open 93c file?


Hi

not need to program 93cxx

BL/BM has a external eeprom (93cxx)

just insert the ept file with Mprog and that's it (93cxx is programmed)

Cheers

[tricoredc17]

Tell someone how to draw input from the program VCDS PETools?

[spychu14]

Polish dump 10.6.5 work with FT232BM/BL

Only for 100+ post members - password by PM :)

[magadan]

Polish dump 10.6.5 work with FT232BM/BL

What serial number will turn out at a cable if to program this dump? If it is a secret, write to a PM.

[wiski]

wrong fusebits
After you have written will be set fusebits ATMEGA
I used same fusebits

[alin 151]

..........................

[perotok]

Ok thanks , i thought that i'm missing a part here. Anyway i had flashed atmega (write and verified OK) but i have blinking red led. Cable shows ok on hardware devices but when connected to car with it shows not connected to car. Tried different 11.11 atmega file but with same error

Hi

Red blinking LED - try flash Atmega again (flash and eeprom)

Set fusebits correctly, check Atmega pins (maybe a bad solder -no contact) or short-circuit on PCB (when you are soldering)

Good luck

[wiski]

Then something was wrong when you have write ATMEGA
What program you use to write Atmega?

Ponyprog, write and verification OK

[perotok]

Ponyprog, write and verification OK


Here's a tutorial how to upgrade the cable with ponyprog

Cable 805 is shown but the same procedure for all cables (just dump different)

[wiski]

This is guide i used. Seems like it is hardware problem in my case.thanks

Sent from my GT-I9100

[KenshinPT]

Polish dump 10.6.5 work with FT232BM/BL

Only for 100+ post members - password by PM :)

Are you sure this dump works 100% Fully Registered on 10.6.5 Polish?

I already tested this dump a few months ago and after 2/3 auto-scans the cable became unregistered.

However, with 10.6.3 Polish the dump works 100% Fully Registered :)

Regards.

[tricoredc17]

Hello!
I have a dump 11.11.3PL. As someone interested in inviting the PW.

[ironderek]

I have small problem with RL cable. After reprogramming when I plug it into the car or test it on the table with external power 12V sometimes led goes green sometimes not at all. Looks like the power doesn't go true. When led light green cable works fine, but when led doesn't light up then I've got message cable not plugged into the car. Sometimes I have to couple times plug in and unplug the cable into the car to powered it.
I don't know where is the problem, I've checked all connection and I didn't find anything. Do you know where is the problem?

[KenshinPT]

I have small problem with RL cable. After reprogramming when I plug it into the car or test it on the table with external power 12V sometimes led goes green sometimes not at all. Looks like the power doesn't go true. When led light green cable works fine, but when led doesn't light up then I've got message cable not plugged into the car. Sometimes I have to couple times plug in and unplug the cable into the car to powered it.
I don't know where is the problem, I've checked all connection and I didn't find anything. Do you know where is the problem?

When you're experiencing that problem, did you check if you have 5V in the output of the 7805?

[ironderek]

There is 5V at the output of the 7805. I think the problem was with connection under the GAL. I tried to fix the cable making wire connection instant programming and solder back the GAL. I fixed couple times few RL cables and everything worked perfect, but this time when I powered up the cable sometimes power goes true and led light lights up and sometimes doesn't. When I soldered back the GAL there is no more problems with the power.

[Meat-Head]

Only for 100+ post members - password by PM :)

Do i have enough posts?



I already tested this dump a few months ago and after 2/3 auto-scans the cable became unregistered.
.

My quality clone from greebd - i have figured out to test the interface when plugging in 'from cold' and it's ok.

but doing a full autosacn ALWAYS flagges up "unlicensed interface"

[spychu14]

[QUOTE=Meat-Head;1657944]Do i have enough posts?

Posts with a little bit of sense - not your bullshitting :D

Just joking :P

[KenshinPT]

My VCDS original installers.

If you f*ck up your cable don't blame me :)

http://sdrv.ms/RN4Ooq (http://sdrv.ms/RN4Ooq)

By the way 11.11.4 with a new FLASH is out... and no, I am not sharing my EEPROM dump :D

137385

Regards.

[mattydr67]

Guys please don't fight.
As you all know if you like to extract the dump which can works with original installers you need to extract from an old kind of tool ( with BM ). This means that the serial to be alocated to a interface with FTDI232BM.
This kind of interfaces are very hard to find.
Now if you extract the dump from a new kind of tools with FTDI 232RQ ( which has it's own ID ), the serial alocated to this kind of tool will ask you always about the FTDI ID ( I mean the VCDS softwears will do this ). The FTDI232RQ ID it is unique.
In this case if you extract the dump from tjis kind of tools with FTDI232RQ you need to modify the VCDS softwear ( the exe file ) to pass the ID.
In this case you cannot use the original softwear from ross-tech.com becasue you need a loader or a moded softwear.
So from what I know Mr. Spychu14 can extract the dump from any VCDS tool and maybe he can make a loader to works with VCDS in Polish.
by the way interfaces with FTDI232BM will be very hard to find because are very old ( relesed 607 or 704 was the last one ) and in the mean time this once was replaced with the once with FTDI232RQ.
And also if you have a dump extracted from a new genuine tool and you make a loader or you mode the VCDS softwear just to pass the FTDI ID's and this softwear get to internet in few seconds the dump will be considerated CLONE and it wiil be blacklisted.
Maybe that's why the dumps cannot be shared, expecially the once from this new once. BUT you can make the softwear to not "get out" to the internet.
Sorry sometime I'm talking to much
Good luck

[magadan]

...After reprogramming when I plug it into the car or test it on the table with external power 12V sometimes led goes green sometimes not at all. Looks like the power doesn't go true. When led light green cable works fine, but when led doesn't light up then I've got message cable not plugged into the car. Sometimes I have to couple times plug in and unplug the cable into the car to powered it...


To me brought in repair a cable. This cable had the same breakage. The cable was sometimes launched if to include to switch on, switch off several times. The static electricity damaged the output cascade of the oscillator in a chip atmega. Fuse-bits were correct. It was necessary to change this chip. But I wanted to read eeprom atmega. I assembled the external oscillator with frequency 7.xx; MHz. I used chip CD4060. I gave a signal on input XTAL_IN. And the cable works already long.



...Now if you extract the dump from a new kind of tools with FTDI 232RQ ( which has it's own ID ), the serial alocated to this kind of tool will ask you always about the FTDI ID ( I mean the VCDS softwears will do this ). The FTDI232RQ ID it is unique.
In this case if you extract the dump from tjis kind of tools with FTDI232RQ you need to modify the VCDS softwear ( the exe file ) to pass the ID.
In this case you cannot use the original softwear from ross-tech.com becasue you need a loader or a moded softwear...
The program (software) remains original when using a loader. Some byte changes. And the result of check ChipID becomes the true. Therefore dumps from new cables work also as well as dumps from old cables.

[mattydr67]

To me brought in repair a cable. This cable had the same breakage. The cable was sometimes launched if to include to switch on, switch off several times. The static electricity damaged the output cascade of the oscillator in a chip atmega. Fuse-bits were correct. It was necessary to change this chip. But I wanted to read eeprom atmega. I assembled the external oscillator with frequency 7.xx; MHz. I used chip CD4060. I gave a signal on input XTAL_IN. And the cable works already long.


The program (software) remains original when using a loader. Some byte changes. And the result of check ChipID becomes the true. Therefore dumps from new cables work also as well as dumps from old cables.

I wanted to say that the dumps from new tools cannot works with original softwears without loader or moded softwears.
In this case you can use it in any kind of tools with BL/BM or RL
Good luck

[mexanico1971]

In the first, cease to load identical photos, or reduce their size.
In the second, compare the diagram of your cable with datasheet a cable.
Of the third be convinced that you didn't make errors when "tuning" cable.
In the fourth, give a cable for repair to experts. It is very difficult to repair a cable if it is impossible to take it in hands.

Try to replace the GAL chip with jumpers. Replace ?tmega. Check soldered details.
I don't see in your photos, three jumpers which are necessary that the cable earned.

every time we try, and every time we fail, we are learning !

[pomarada]

Hello
Well, my pulse is not what it was and almost break the cable, fortunately works well with the version I have.

but I like it, try to do these things and buy another with a different version if not fool me with Atmega and BL, and I think firmware 1.91
When you have it in my hands, I will try to do it again

greetings and thank you all for your help

[borysgo2]

GAL remove solution.
One of members GF forum posted how to remove GAL from pcb with RL chip, today i did cable with BL usb converter, there is only one small diffrence. Hope it will be helpfull.

[perotok]

GAL remove solution.
One of members GF forum posted how to remove GAL from pcb with RL chip, today i did cable with BL usb converter, there is only one small diffrence. Hope it will be helpfull.



for BL/BM cables is not necessary to remove the GAL (only for RL cables) :beerglass:

[mattydr67]

Hi
Is there anyone who has the new firmwear ( flash ) 1.92?
If yes please share it here.
Thanks
Good luck

[alin 151]

..........................

[magadan]

... Is there anyone who has the new firmwear ( flash ) 1.92?
If yes please share it here....
It is a flash from cables of old assembly (FT232B, 256 words bootloader).

And who has a flash from cables of new assembly (FT232R, 512 words bootloader)?

[mattydr67]

I have a cable with vcds11.11.0 fw1.84 ft232bl
After installation of vcds11.11.4, the cable requires update to fw1.92.
I can update and read ATMEGA
This is helpful?

Yes it is helpfull indead.
Thanks very much
My friend magadan did this for me yet
Thanks
Good luck

[mattydr67]

It is a flash from cables of old assembly (FT232B, 256 words bootloader).

And who has a flash from cables of new assembly (FT232R, 512 words bootloader)?

This is what I need
Thanks very much my friend
Good luck

[t1nc1]

great forum.. lots of info.
thanks very much

[alin 151]

---------------------------

[magadan]

This is the dump extracted after update fw1.92!
Eeprom and flash...
The flash is similar as mine.
Yours eeprom is already killed, look at the address 00000016 (if can transfer to a bin-format).

[alin 151]

..........................

[mattydr67]

Thanks
Don't worry about this Alin
The flash it is good and it is the same as magadan one.
The eeprom I knew it that it is not good.
The VCDS softwear can upgrade just the flash in your toolbut will not change your serial with other. The eeprom remain the same don't metter what the version you use.
And if you have a VCDS 11.11.0 eeprom this one it is blacklisted in newer version then 11.11.0

Thanks again and Good Luck

[1 6 D]

There was on RT site unofficial installer of 11.11.4 which was working with fw1.91. It was on their server for about a week.

[mattydr67]

Mate
VCDS 11.11.4 works with any firmwear ( flash ).
BUT IT NEEDS fw 1.92 if you want to make a corect diagnostic or to not damage your car when you do any adaptation or coding.
Take care with this.
I can use flash 1.84 with this softwear but it is need 1.92 to works correctly.

Good luck

[1 6 D]

My installer was able to download from about 1.8.2012 to 6.8.2012, when RT say on their site that actual version is 11.11.3. Official 11.11.4 comes about 13.8.2012. My friend have tested my installer with 1.84 dump from 11.11.0 from 204 site, it makes update to 1.91. But he can only see coding and serial was reistered. When he tried to code module, VCDS makes unregistered.

[magadan]

There was on RT site unofficial installer of 11.11.4 which was working with fw1.91. It was on their server for about a week.
The archive is damaged. Load again please.

[cgrex]

This is my first post, so please go easy on me.

I have looked back at the start of this thread and I am really finding it hard to unstand whats what.

I have got a Cable and software from China. the version is 11.11.2

it works fine with my 2012 Audi A4 B8, apart from the breaking module. I think I will need a newer verson of VCDS, for this to work.

I know I can't just download the latest verson of VCDS (11..11.4) but will there be a way for me to update my cable and get 11.11.4 to work?

thanks

[mattydr67]

This is my first post, so please go easy on me.

I have looked back at the start of this thread and I am really finding it hard to unstand whats what.

I have got a Cable and software from China. the version is 11.11.2

it works fine with my 2012 Audi A4 B8, apart from the breaking module. I think I will need a newer verson of VCDS, for this to work.

I know I can't just download the latest verson of VCDS (11..11.4) but will there be a way for me to update my cable and get 11.11.4 to work?

thanks

A way it is.
You just need the dump for new VCDS 11.11.4 ( and maybe a moded or a loader for this version )
BTW do you think that it is a softwear has no coverage for your cara and that's why you cannot connect to your controler?
I suppose that your Chinese moded softwear has bugs.
I have VCDS 11.11.2 and I haven't any car in which I cannot conect to its all controlers. And I'm also talking about 2012 cars.
Good luck

[liviudiaconu]

The archive is damaged. Load again please.

Is not damaged...is named "VCDS-Release-11.11.4-Installer.EXE.zip".. rename-it in "VCDS-Release-11.11.4-Installer.zip" (without .exe) and work..

[magadan]

Is not damaged...is named "VCDS-Release-11.11.4-Installer.EXE.zip".. rename-it in "VCDS-Release-11.11.4-Installer.zip" (without .exe) and work..
Excuse me. My "Internet Explorer" downloaded not all archive. I downloaded with the help "Opera", and everything is good.

[1 6 D]

I have packed it with zip, not rename. I have reposted it in last post.

BTW:
Does anybody have german 11.2 Beta installer?

[magadan]

Does anybody have german 11.2 Beta installer?
I have no version 11.2 Beta, but I have versions 10.6.4 of firms (DRV,AIB,MFT,PCI). If it is interesting, I can give.

Only versions AIB,DRV - installer. Remain as portably versions.

[roka]

.I'm sorry I ruined

[roka]

Hello!
I bought one killed me (updated) cable: I'll suffer with it a bit.
Haha ..... more help
It was inquired to the CD in English VCDS 10.6.4. was.
First, because this version was installed as VCDS.hu to English (it still worked!) And was followed by the version 11.11.1 r?dugt?k Picked the car after it has been able to read the error and the reset button is pressed, a window it was no longer know what it was, and from that point on will not work.
Machine can not be connected to Hex-can be recognized as an unknown device interface instead, and vid-pid values ***8203;***8203;are always 0 I'll put up pictures of him because this is included in the particular STC MCU.
The diode and resistor in there. Have you met someone with this type.
Thank you in advance.
.Finally I made my request to ask the

[cgrex]

A way it is.
You just need the dump for new VCDS 11.11.4 ( and maybe a moded or a loader for this version )
BTW do you think that it is a softwear has no coverage for your cara and that's why you cannot connect to your controler?
I suppose that your Chinese moded softwear has bugs.
I have VCDS 11.11.2 and I haven't any car in which I cannot conect to its all controlers. And I'm also talking about 2012 cars.
Good luck

I have looked on forums and they have said that the software doesn't work with some new models yet, like A4's and A5's. This way I am thinking it is the version 11.11.4 I am needing.

I take it I will have to wait for a dump of the new 11.11.4? Will I need to update the cable firmware then, is that what the dump is? Sorry I'm not sure what to do.

[mattydr67]

I have looked on forums and they have said that the software doesn't work with some new models yet, like A4's and A5's. This way I am thinking it is the version 11.11.4 I am needing.

I take it I will have to wait for a dump of the new 11.11.4? Will I need to update the cable firmware then, is that what the dump is? Sorry I'm not sure what to do.

Mate
As I told you before you have a cracked Chinese softwear which as VCDS 11.11.3 Chinese crack has a lot of bugs ( as a lot of chinese craked VCDS softwears )
About the VCDS 11..11.4 of course you can wait the dump, it is your choice.
The dump means flash ( firmwear ) and eeprom ( menas the serial )
The firmwear it is easy to get and you can downloaded from here. Magadan and Alin51 shared.
Take care about Alin51 stuff becasue it contacins eeprom from VCDS 11.11.0 and if you use it in your tool then this one will not work with your VCDS 11.11.2. So take care what you doing.
Well some controls cannot be accessed directly. You need to do it thru another controllers as are 09 or 46 ( you have to read about this in Ross-Tech web site ).
Good luck

[KenshinPT]

I have looked on forums and they have said that the software doesn't work with some new models yet, like A4's and A5's. This way I am thinking it is the version 11.11.4 I am needing.

I take it I will have to wait for a dump of the new 11.11.4? Will I need to update the cable firmware then, is that what the dump is? Sorry I'm not sure what to do.

You can wait for 11.11.4 dump, but make you sure you get a confortable chair because it can took a while - 6 months or a year.

If we're talking about others dumps than english, you can wait forever...

Regards.

[1 6 D]

What can You say about version of 11.11.4 which I have posted?

My friend have tried it with 11.11.0 dump, it updated firmware to 1.91 and he can only look on coding, measuring blocks and adaptation channels.

Maybe someone else have tested it?

[KenshinPT]

What can You say about version of 11.11.4 which I have posted?

My friend have tried it with 11.11.0 dump, it updated firmware to 1.91 and he can only look on coding, measuring blocks and adaptation channels.

Maybe someone else have tested it?

I can say that the 11.11.4 installer you've posted has the serial from 11.11.0 EEPROM dump available here on DK on its blacklist.

Regards.

[1 6 D]

Have somebody fw1.91 for 11.11.3 and can try it with this version?

[KenshinPT]

Have somebody fw1.91 for 11.11.3 and can try it with this version?

The problem here is to get the EEPROM (serial) and not the FLASH (firmware).

So, to answer you, my flash (1.91 or 1.92) works on 11.11.4 but only because I have a serial (EEPROM) which is not banned, yet.

Regards.

[mattydr67]

What can You say about version of 11.11.4 which I have posted?

My friend have tried it with 11.11.0 dump, it updated firmware to 1.91 and he can only look on coding, measuring blocks and adaptation channels.

Maybe someone else have tested it?

Mate stop dreaming.
If you want to erase your Atemga please use that softwears and then you'll cry.
Forget about this. All this dumps which are for free now are blacklisted in higher version. So the last version of dump which is free it is 11.11.0 So in next 11.11.1 this dump it is blacklisted and it will be blacklisted forever.
In VCDS 11.11.4 how it will be? BLACKLISTED
Good luck

[perotok]

Hi matty

What is this version
11.11.0-Installer*_Perfect!





Cheers

[1 6 D]

Size of it is the same like original installer, after unpack dates of files are the same too.

[ahadi]

The problem here is to get the EEPROM (serial) and not the FLASH (firmware).

So, to answer you, my flash (1.91 or 1.92) works on 11.11.4 but only because I have a serial (EEPROM) which is not banned, yet.

Regards.

Share for testing .:roflmao:

[iustin73]

"805.0" ept ftdi 232 rl please

[mattydr67]

"805.0" ept ftdi 232 rl please

Justin the ept file it is the same for FTDI232RL
Here it is
Good luck

[J_amb_o]

Hi all,

I have VCDS 106 cable, runs version 10.6.0, no issue. Is there a newer software I can use without reprog/reflashing anything?

J

[perotok]

Hi all,

I have VCDS 106 cable, runs version 10.6.0, no issue. Is there a newer software I can use without reprog/reflashing anything?

J


No

You can not use a newer version of VCDS without flashing Atmega (flash+eeprom)
You must program the ATMEGA162 with new dump (the last free dump is 11.11.0)

[J_amb_o]

Thanks. I could do with a spare cable so I will keep this one as is.

What is the latest reliable version out there? I have seen 11.10 for around ***8364;25

[teerak2uk]

I have a 3 cables 10.6.4, 11.8, 11.10 the 10.6.4 is left on that version as backup and the 11.8 is running 11.3 but 11.10 won't run 11.10 only runs 11.3 the ftdi are BL versions what options do I have on these and what h/w are people using to flash atmega

Thanks.

[colouny]

Hi all, I ahve 11.11 interface at least it is written on it. It became unregistered after few sessions with internet connected, need to do the coding and adaptation... Bad luck/ or my brain is degrading with the age... :D forgot to disconect...
Any way it has the BL chip, and it worked fine. I am not chasing the latest version just need the 11.11.0, want to restore as it was before.
What i would like to ask if someone could point me to the place where i could download the dump for atmega, and ftdi, and also the vcds installer for that goes with these dumps. Or i can use the one that came with my interface?
And one more thing, do i really need to remove the IC8, T5, R50 for the thing to reflash properly?

I am adding pictures of my interface.
Thanks in advance.

[KenshinPT]

Hi all, I ahve 11.11 interface at least it is written on it. It became unregistered after few sessions with internet connected, need to do the coding and adaptation... Bad luck/ or my brain is degrading with the age... :D forgot to disconect...
Any way it has the BL chip, and it worked fine. I am not chasing the latest version just need the 11.11.0, want to restore as it was before.
What i would like to ask if someone could point me to the place where i could download the dump for atmega, and ftdi, and also the vcds installer for that goes with these dumps. Or i can use the one that came with my interface?
And one more thing, do i really need to remove the IC8, T5, R50 for the thing to reflash properly?

I am adding pictures of my interface.
Thanks in advance.

Yup, you should remove those components!

[colouny]

Yup, you should remove those components!

Any dumps?

[mirko1]

Hi,
11.11.0 it is the latest worked wersion with BL/BM?

[mattydr67]

Hi,
11.11.0 it is the latest worked wersion with BL/BM?

If you mean the last for free. YES
Good luck

[arturkob]

Any dumps?

is dump for your pcb

[colouny]

is dump for your pcb

Thanks, will try this one. ;)

[cosmind]

is dump for your pcb

you canot read atmega from vcds. is protected! check your dump...

[arturkob]

Thanks, will try this one. ;)

try this maybe ok

[colouny]

No luck for me, spent at least 3 hours reflashing and testing ( MKV Jetta & VW Golf MK3).
Always get the same shi...y error.
Posting the pictures, Please let me know if there is something more to try...
By the way i am using TRUE LPT port and ISP Programmer 1.2.0.56

Thank you in advance

[KenshinPT]

No luck for me, spent at least 3 hours reflashing and testing ( MKV Jetta & VW Golf MK3).
Always get the same shi...y error.
Posting the pictures, Please let me know if there is something more to try...
By the way i am using TRUE LPT port and ISP Programmer 1.2.0.56

Thank you in advance

Do you have this error if you test the cable in your workbench, and not connected to the car? That sound a problem with an aftermarket radio

http://www.ross-tech.com/vag-com/aftermarket-radio.html

[colouny]

Do you have this error if you test the cable in your workbench, and not connected to the car? That sound a problem with an aftermarket radio

Ross-Tech: VCDS: Afterrmarket Radio Problem (http://www.ross-tech.com/vag-com/aftermarket-radio.html)

Nope, the radio is ok,
Had to work with 10.6 today instead of 11.11, needed coding and the labels are not avalible. Needed to recode the 09 from US to EU with rear foglight and LED tails. Everything went smooth with 10.6, it was my backup cable, and now it seems to be my primary :D, althow its very old...
By the way radio is original in that car. Car was 2007 Jetta.

Could this be caused due to incorect cables, i mean the blue one that i have to connet after i remove the STC.




And maybe someone has RUSSIAN version? My firend is ready to pay some $. Please PM for russian... Thanks

[magadan]

And maybe someone has RUSSIAN version? My firend is ready to pay some $. Please PM for russian... Thanks
If you Russian, look at this site.
http://rutracker.org/forum/viewtopic.php?t=3585870
http://rutracker.org/forum/viewtopic.php?t=3976562
There is "Vasya Diagnost" (VCDS on Russian) of the version 11.2 and 10.6 free of charge.
Also there are still new versions, but isn't free.
There is an instruction on cable repair in Russian.

[colouny]

If you Russian, look at this site.
http://rutracker.org/forum/viewtopic.php?t=3585870
http://rutracker.org/forum/viewtopic.php?t=3976562
There is Vasya Diagnost of he version 11.2 and 10.6 free of charge.
Also there are still new versions, but isn't free.
There is an instruction on cable repair in Russian.

I am not russian, I read russian, but with great difficulty.
Anyway, these torrents are long known for me, the EPT for Vasya Diagnost is empy, any data at all, tired on 3 PC's to download it and tried to flash it with no luck. Whenever i load it to Mprog no data is loaded, so results...

Maybe you have smth that works with Vasya Diagnost? Or Dump that sould be working with English 11.11
I Still believe that i will succeed to get the interface woking.

[dlhy]

No luck for me, spent at least 3 hours reflashing and testing ( MKV Jetta & VW Golf MK3).
Always get the same shi...y error.
Posting the pictures, Please let me know if there is something more to try...
By the way i am using TRUE LPT port and ISP Programmer 1.2.0.56

Thank you in advance

Do you set correct fusebits?

[colouny]

Do you set correct fusebits?

Cant relly say exactly. But i think they are correct. But just in case which are correct?
Thx

[mattydr67]

Cant relly say exactly. But i think they are correct. But just in case which are correct?
Thx

Look here
http://www.digital-kaos.co.uk/forums/f152/vag-com-vcds-everything-99750/index76.html#post1592131
CD - DC - F9 - FF - FFFFFF56
or
CD - DC - F9 - CC - FFFFFF56
if you use Extreme Burner
Dosen't metter which one.
Or you can trunsforme item if you use other kind or programmer
Good luck

[ahadi]

hello all ,

i update a cable to 11.11.0 ,interface test ok . but when connect to the car the vcds stalls .

[perotok]

Cant relly say exactly. But i think they are correct. But just in case which are correct?
Thx


Look here

Engbedded AVR Fuse Calculator (http://www.engbedded.com/fusecalc/)

Select Atmega162

Good luck

[perotok]

hello all ,

i update a cable to 11.11.0 ,interface test ok . but when connect to the car the vcds stalls .


Reflash Atmega162 again ( flash+eeprom) with external programmer and set fusebits correctly

[colouny]

Look here

Engbedded AVR Fuse Calculator (http://www.engbedded.com/fusecalc/)

Select Atmega162

Good luck

Thanks, will try tOmorrw.

[dlhy]

Cant relly say exactly. But i think they are correct. But just in case which are correct?
Thx
Im using this

[ahadi]

Reflash Atmega162 again ( flash+eeprom) with external programmer and set fusebits correctly

i did , can bus works fine but diagnose through kwp still stalls specially when clearing faults. any idea please .

[1 6 D]

My friend give me his VAG106 cable with FT232RL, like in this post:
http://www.digital-kaos.co.uk/forums/f152/vag-com-vcds-everything-99750/index70.html#post963761
There is a problem that with 10.6.2 after few minutes of work it makes unregistered and I have to repair only FTDI to work again.

Can somebody give me link to post with latest free dumps for this RL cable which don't make unregistered after few minutes? It's hard to chech all 200 pages to find link fir download

[mattydr67]

My friend give me his VAG106 cable with FT232RL, like in this post:
http://www.digital-kaos.co.uk/forums/f152/vag-com-vcds-everything-99750/index70.html#post963761
There is a problem that with 10.6.2 after few minutes of work it makes unregistered and I have to repair only FTDI to work again.

Can somebody give me link to post with latest free dumps for this RL cable which don't make unregistered after few minutes?

if you'll read this huge thred you'll see that you'll find it.
The last free dumps it is for VCDS 11.11.0
And for RL tools you'll need a loader or a moded softwear as the vCDS 10.6.2 you've have.
But if you have a RL tool you need to search for the tutorial how to fix this kind of tools. You can find this tutorial here too.
As you know if you have an internet connection on the computer where the VCDS softwear it is installed, this will become unregistred in few time. This because the ross-tech changes how to check the clones and I realized that even you write the name of the update server into the hosts your tool will become unregistred.
Good


P.S. - The VCDS 10.6.2 Chinese softwear was bad cracked as it is the new Chinese VCDS 11.11.2 and VCDS 11.11.3 - bad cracked

[ahadi]

hello ,

vcds 11.11.1 may solve the issue losing communication with vcds11.11.0 .mabe it is driver issue.

[zeljolaki]

Hello!
* I use VCDS software, version 10.6, it often happens that we break the damp in the interface, sometimes several times a day.
I work with a computer is not connected to the Internet.
What do you think why is this happening?
Is there a way to lock the Atmega hardware, to prevent this?

[mattydr67]

Hello!
* I use VCDS software, version 10.6, it often happens that we break the damp in the interface, sometimes several times a day.
I work with a computer is not connected to the Internet.
What do you think why is this happening?
Is there a way to lock the Atmega hardware, to prevent this?

If you didn't use the internet conection in that PC never then you have a hardwear issues in your tool.
Atmega cannot be erased if you never had an internet conection in that computer.
Or you use other version of softwear then you need ( diffrent that for your dump )
Good luck

[zeljolaki]

If you didn't use the internet conection in that PC never then you have a hardwear issues in your tool.
Atmega cannot be erased if you never had an internet conection in that computer.
Or you use other version of softwear then you need ( diffrent that for your dump )
Good luck

My computer is not connected to the Internet, damp and software are compatible, the software works when it works perfectly .. whether it may be on the computer and I have VCDS lite cracked software?

[mattydr67]

My computer is not connected to the Internet, damp and software are compatible, the software works when it works perfectly .. whether it may be on the computer and I have VCDS lite cracked software?

VCDS Lite it is totally diffrent softwers. No way, there's no conflict between VCDS Lite and VCDS for HEX CAN tool.
If your interface is blocking in the middle of diagnostic or it become Unregistred suddenly this can be because the FTDI can be "bad" aspecially if your FTDI is BM or the GAL/ATF it is "bad"
But if your tools works like a charm in that computer where you say that there no internet connection ( never not just in the mean time with a dignostic session ) this means that the ATMEGA can be erased.
Good luck

[gtr61]

i have 11.11 clone cable with cd fill up some vagcom realeses i install 11.11.2 software and plug cable car it reads modules and everything looks wonderfull... and when i try some coding it says code accepted but not coding anything any way to run this cable without problems

edit cd haves mprog and ept file, when read the cable on mprog says like .T .0 .0 .0 .0 .0 .1 .. and then when i write the ept file it says .i .V .P .1 .6 .L .R .. but when i reconnect cable it says again .T .0 .0 .0 .0 .0 .1

[magadan]

edit cd haves mprog and ept file, when read the cable on mprog says like .T .0 .0 .0 .0 .0 .1 .. and then when i write the ept file it says .i .V .P .1 .6 .L .R .. but when i reconnect cable it says again .T .0 .0 .0 .0 .0 .1
Disable chip protect (STC....).

[liviudiaconu]

My computer is not connected to the Internet, damp and software are compatible, the software works when it works perfectly .. whether it may be on the computer and I have VCDS lite cracked software?

Uninstall all vcds versions, uninstall too drivers with ftclean, DISABLE ALL network adapters (wireless and cable)...reinstal soft and drivers
If the problemm reappear, try with another cable to see if your cable has an issue (FT232 Bx almost all cases, that if you don't need to rewrite atmega).

[reter]

Uninstall all vcds versions, uninstall too drivers with ftclean, DISABLE ALL network adapters (wireless and cable)...reinstal soft and drivers
If the problemm reappear, try with another cable to see if your cable has an issue.

i have the same problem. please read after find decision

[Artilect]

This is another cable 10.6 with BL ftdi which
works ok with 11.11.0

M8 this circuit board have already ISP connections prepared.

If you look closer you vill see the blank connections near by the USB cable pads. You just have to solder 5 pins to it (mosi, miso, SCK,RST) and get 12V via OBD. And you are free to flash without anoyng soldering on the chip legs.

BR

[teerak2uk]

M8 this circuit board have already ISP connections prepared.

If you look closer you vill see the blank connections near by the USB cable pads. You just have to solder 5 pins to it (mosi, miso, SCK,RST) and get 12V via OBD. And you are free to flash without anoyng soldering on the chip legs.

BR

Which chips on the board can be flashed this way

[Artilect]

Atmega for sure.

FTDI is flashable via USB.

BR

[Artilect]

At the end its look like this.

And dont forget to connect GND. You can also use ISP supply voltage if you have beeprog or similar. Then jou have to solder two wires to voltage reg.

:)

[Artilect]

With this version of circuit board you have to remove smal Flashing chip. Othervise he will reflash FTDI dump at power on.

[ironderek]

With this version of circuit board you have to remove smal Flashing chip. Othervise he will reflash FTDI dump at power on.

You probably talking about this chip :) So everybody who has this type of PCB board has to remove it

[Artilect]

Yes the STC is placed ther to flash the FTDI dump over vhen the power is on.

[giuseppe1374]

hi, I hope someone help me, I have this pcb vcds, unfortunately I was very careless connecting the PC to the internet and after a few days I connected the cable, unfortunately, I think he is dead (not registered, not authorized in red) so I uploads the post # 3157 but unfortunately is unauthorized and unregistered I tried it on a PC that has never connected to the internet and with a new installation of vcds, please someone help me, thank you very much

[liviudiaconu]

You can update atmega as'is? Try to remove the stc (red pointed). That because i have one aproximately like in Artilect's photo (the quartz are not at 45 degree in my cable) and cannot write with STC mounted.

[colouny]

Does anyone have The 11.11 files sparated into Flash.hex or .bin and Eeprom.hex or .bin?

Or how do i separate them?
Need this because o am using ISPProgrammer and i doeas support only two sepparate files.

Thanks

[mattydr67]

Does anyone have The 11.11 files sparated into Flash.hex or .bin and Eeprom.hex or .bin?

Or how do i separate them?
Need this because o am using ISPProgrammer and i doeas support only two sepparate files.

Thanks

You can separate it in eeprom and flash using PonyProg
Uploade the file
Then save eeprom and flash as hex file
Good luck

[colouny]

You can separate it in eeprom and flash using PonyProg
Uploade the file
Then save eeprom and flash as hex file
Good luck

The reason i ash is that i cant use ponyProg, i am on win8 for like 1 year. But thanks for hint i still have very old laptop wich still has XP will try today.

[mattydr67]

The reason i ash is that i cant use ponyProg, i am on win8 for like 1 year. But thanks for hint i still have very old laptop wich still has XP will try today.[/quote]

You didn't mention this.
Good luck

[giuseppe1374]

You can update atmega as'is? Try to remove the stc (red pointed). That because i have one aproximately like in Artilect's photo (the quartz are not at 45 degree in my cable) and cannot write with STC mounted.



hi, I removed the chip stc I reflashed again but I connected the cable 12v DC and I did tests on vcds software, the result, "cable is not connected to the car," after I was distracted and I reflashed with the usb cable attached and without 12v, result led off hours and ATmega seems dead, can not flashed again, any solution?

[liviudiaconu]

when you reflash atmega, atmega must be powered.

How?
1 power on the cable (+12V)
2 power on atmega from programmer (+5V on pin 3 of 7805).

[giuseppe1374]

Yes, I've done as you said, but later because of many tests I was confused and I reflashed without 12v of 7805 but with usb cable attached and now ATmega seems dead, no longer possibbile reflashed again

[liviudiaconu]

Is possible with "atmega doctor"

Atmega HVPP fusebit doctor ***8211; napraw fusebity, fix fusebits >> Manekinen DIY (http://diy.elektroda.eu/atmega-fusebit-doctor-hvpp/?lang=en)

Have anyone schematic for this newest cables?

[giuseppe1374]

the ATmega doctor you can buy? I do not think I am able to build

[liviudiaconu]

i don't know, i made it myself..
but to buy mean you work with much [b]locked atmega...
With price of doctor you can buy few newest atmega..

[colouny]

The reason i ash is that i cant use ponyProg, i am on win8 for like 1 year. But thanks for hint i still have very old laptop wich still has XP will try today.

You didn't mention this.
Good luck[/QUOTE]

No problem, have sorted everything pretty easy on my old laptop. Thanks again for hint.
11.11 tested on one car, still works, will se how it goes. No i need to do the same for the polish version for my firend...

[mattydr67]

You didn't mention this.
Good luck[quote/]

No problem, have sorted everything pretty easy on my old laptop. Thanks again for hint.
11.11 tested on one car, still works, will se how it goes. No i need to do the same for the polish version for my firend...

If you have polish dump you can do it.
Good luck

[giuseppe1374]

many thanks to all those who helped me, I mean I bought a new ATmega, I reflashed and my cable is now in life, so I think that when the cable has 12v power but the LED is off, this means that ATmega is dead. greetings to all forum users.
very best regards

[KenshinPT]

many thanks to all those who helped me, I mean I bought a new ATmega, I reflashed and my cable is now in life, so I think that when the cable has 12v power but the LED is off, this means that ATmega is dead. greetings to all forum users.
very best regards

Very nice :)

Keep in mind that you might wrongly disabled SPIEN for that "dead" ATMEGA :)

But you don't have HVPP to check it right?!

Good luck.

Regards.

[liviudiaconu]

with serial programmer cannot disable SPIEN.. on most programmers is "grayed"... but i have found that if during programming the power of atmega is disconected or a wire between programmer and atmega is desoldered (to me the gnd was intrerrupted) is possible to lock "forever" the atmega.

But, is easy to repair with "atmega doctor", in fact an "reduced HVPP", who write like HVPP but only the factory bits from a list from firmware.

[giuseppe1374]

Hi, sorry, it's still me, today I made a new reading but the cable does not seem to be working properly read I did the test and exit "short +12" What can it be?

[bibkare]

Hi, sorry, it's still me, today I made a new reading but the cable does not seem to be working properly read I did the test and exit "short +12" What can it be?

You have one broken transistor, i bet it's this one in yellow circle

http://i47.tinypic.com/wwmc9d.jpg

[giuseppe1374]

how can I measure this transistor?

[KenshinPT]

Hi, sorry, it's still me, today I made a new reading but the cable does not seem to be working properly read I did the test and exit "short +12" What can it be?

Also, recheck all solders of the ATMEGA. If you replace it, you might have short or the PCB is not cleaned well making a short between pads.

I have this problem once. K Line shorted due to excess of flux.

So: Clean PCB, recheck all solder pads of ATMEGA and also test those 4 transistors.

Good luck.

Regards.

[KenshinPT]

how can I measure this transistor?

When a transistor is bad... 99.9999999% of those times it is shorted instead of open.

So use a multimer in the continuity mode. I bet you will hear a BIP BIP or BUZZ BUZZ or PIP PIP :D


Good luck

[giuseppe1374]

thanks to KenshinPT I solved my problem, welds are perfect I've done a lot in my life, the problem of flux pcb dirty, I cleaned it with the triellina and now everything works perfectly, thank you in a special way KenshinPT, but also bibkare, their two are great people.

[KenshinPT]

thanks to KenshinPT I solved my problem, welds are perfect I've done a lot in my life, the problem of flux pcb dirty, I cleaned it with the triellina and now everything works perfectly, thank you in a special way KenshinPT, but also bibkare, their two are great people.

We are always learning!

In my humble opinion, what makes someone expert is not making the same error twice :)

I believe, that next time you will pay more atention about the flux cleaning :)

Good luck.

[karcsi32]

hello!

VAG-COM ,WCDS process collection i needed.
sorry for my bad english !
thank you !

[skubbe]

Thank you, this thread was very helpfull!

[pauleemor]

hope someone can help vag 113 when connect to car it shows attached thanx

[mattydr67]

hope someone can help vag 113 when connect to car it shows attached thanx

Reinstall the VCDS anbd do the interface TEST again
If in ABOUT it is UNREGISTRED ....you had bad luck
The ATMEGA eeprom it was erased
Good luck

[ironderek]

I had fix RL cable and install software with loader on XP machine-everything works perfect, but when I try to install to same software on Windows 7 64bit I've got error message "Wrong Filesize", any idea why, and how to fix it? Cable works ok on Windows XP, but cannot install it on W7 64bit???

[mattydr67]

I had fix RL cable and install software with loader on XP machine-everything works perfect, but when I try to install to same software on Windows 7 64bit I've got error message "Wrong Filesize", any idea why, and how to fix it? Cable works ok on Windows XP, but cannot install it on W7 64bit???

From what i know the loaders for interface with FTDI RL are JUST for Windows 32bit not for 64bit.
Good luck

[magadan]

I had fix RL cable and install software with loader on XP machine-everything works perfect, but when I try to install to same software on Windows 7 64bit I've got error message "Wrong Filesize", any idea why, and how to fix it? Cable works ok on Windows XP, but cannot install it on W7 64bit???
Copy the file "vcds.exe" from the 32-bit program, in the folder on other computer where there is a 64-bit program. Also you can launch the program on the 64-bit computer using a loader.

Or select from the menu point "To install the 32-bit program on the 64-bit computer". This menu appears at the beginning of VCDS program installation.

[bogdi19]

Can any one help me repair my vag com cable that was connected to internet?
The cable uses FT232BL.
Thanks in advance!

[ironderek]

Copy the file "vcds.exe" from the 32-bit program, in the folder on other computer where there is a 64-bit program. Also you can launch the program on the 64-bit computer using a loader.

Or select from the menu point "To install the 32-bit program on the 64-bit computer". This menu appears at the beginning of VCDS program installation.

Thanks magadan, but this is my problem when I try to use/launch loader on 64bit OS I've got error message "Wrong Filesize". To same loader on XP 32bit OS works fine.

[magadan]

...but this is my problem when I try to use/launch loader on 64bit OS I've got error message "Wrong Filesize"....
The file "vcds.exe" for 32-bit system and the file "vcds.exe" for 64-bit system aren't equal on the size. These files have different codes in a random access memory. Therefore the loader doesn't work.

Also the loader always is calculated for one and the same of the file "vcds.exe". If to use a loader for other file (other bit-sistem, other version program, non windows-program etc.), you will receive this error.

[beriv]

Hello. I need some help regarding the VG.B 2011.07.01 FTDI 232BL interface if you don't mind.
It showed unregistred, that's why I tried to update 1.92 FW.
I connected it to an Atmega 162 chip (based on a description I found). It had a continuous red light, but it stopped a bit later.
I decided to wait a bit, but nothing happened.
When I started to read with with the "pony-prog" is showed "device not found".
In the meantime I found an other picture\description on the net which had no gal chip at all, but it had an older cicruit board "VG.A".

Shall I try to flash based on this second description, or do you have any idea?

Thanks for your time, waiting for your answer.

http://www.digital-kaos.co.uk/forums/attachments/f152/137968d1345227767-vag-com-vcds-everything-vcds-no-gal.rar

http://imageshack.us/photo/my-images/259/dsc0503t.jpg/

[KenshinPT]

Hello. I need some help regarding the VG.B 2011.07.01 FTDI 232BL interface if you don't mind.
It showed unregistred, that's why I tried to update 1.92 FW.
I connected it to an Atmega 162 chip (based on a description I found). It had a continuous red light, but it stopped a bit later.
I decided to wait a bit, but nothing happened.
When I started to read with with the "pony-prog" is showed "device not found".
In the meantime I found an other picture\description on the net which had no gal chip at all, but it had an older cicruit board "VG.A".

Shall I try to flash based on this second description, or do you have any idea?

Thanks for your time, waiting for your answer.

http://www.digital-kaos.co.uk/forums/attachments/f152/137968d1345227767-vag-com-vcds-everything-vcds-no-gal.rar

ImageShack® - Online Photo and Video Hosting (http://imageshack.us/photo/my-images/259/dsc0503t.jpg/)

If you have a BL chip you don't need to remove or reflash the GAL.

But you need to remove the STC chip, a resistor and the transistor.

Then, reflash FTDI232BL and ATMEGA.

Good luck.

[beriv]

Ok thanks for the hint
I know how to reflash ATMEGA, but I could use some help, how to refash FTDI232BL
Can you help me please?

[mattydr67]

Ok thanks for the hint
I know how to reflash ATMEGA, but I could use some help, how to refash FTDI232BL
Can you help me please?

Using MProg and the ept file for FTDI BL/BM
For FTDI RL it is diffren of course

Good luck

[rsebastian]

Hello, I new in this area so please be patience with me. I read almost the entire thread but when you start something is kind a confuse to understand everything.

I have a cable 11.8 that i want to update to 11.11 (see pics attach) and is not broken. The cable has this components: FT232BL, 93c56wp, atmega162.

I think is importan to say that the cable doesn?t have T5 and IC8, but it does have R50.

So with this information, what to i have to do first, i think is somenthing similar to a case that is in page 204 and 206 but i'm not sure.

Thank you in advance for your kindly support. Regards from Guatemala :bounce:

[ssilvviu]

You just have to program Atmega with a proper dump.

[skubbe]

Hello, I new in this area so please be patience with me. I read almost the entire thread but when you start something is kind a confuse to understand everything.

I have a cable 11.8 that i want to update to 11.11 (see pics attach) and is not broken. The cable has this components: FT232BL, 93c56wp, atmega162.

I think is importan to say that the cable doesn?t have T5 and IC8, but it does have R50.

So with this information, what to i have to do first, i think is somenthing similar to a case that is in page 204 and 206 but i'm not sure.

Thank you in advance for your kindly support. Regards from Guatemala :bounce:


Hi, i have exactly similar cable, but originally with version 11.11.0. I managed to kill it with internet connection accidentally on. Vcds says it?s not registered so i can?t use it properly anymore.

So in order to restore it (11.11.0 is ok for me, no need for update) should i just follow the tutorial from message #95, but instead of using old dumps, i use files from message # 3157?

And just to make sure, i don?t have to remove any components since i don?t have T5 or IC8?

Thanks in advance!

[patamatcz]

My thread is more about "Finding good dump"...

Hello. Have You dump for vcds 10.6 ?

[rsebastian]

You just have to program Atmega with a proper dump.

Ok, so this is what i dont know how, i mean it's not clear for me.

1.- To program Atmega i have to use Ponyprog?
2.- Do I have to do the same procedure with Ponyprog described in the tutorial that appers in the firsts pages?
3.- If i have to do the same procedure of the tutorial... do i have to solder the 4 wires to the Atmega?
4.- The dump for atmega is the file named "dump.bin" right?

Thanks again for your support. A step by step will be apreciate here or by pm.

Regards from Guatemala. :ciao:

[pomarada]

Hello
I'm looking for a reliable seller, you have the vcds with ATMEGA162 and FTDI232BL.
Also that the motherboard is like this, for soldering, a newbie like me.
I find nothing.
Do you know of any?

regards

[1 6 D]

I have bought USBasp and I have a problem now.
I can't use Ponyprog with it. I have connected my Atmega with extreme burner and this program need separate file for flash and for eeprom. How can I modify single hex with flash and eeprom to separate files? Or maybe somebody have them converted for 11.11.0 version?

[perotok]

I have bought USBasp and I have a problem now.
I can't use Ponyprog with it. I have connected my Atmega with extreme burner and this program need separate file for flash and for eeprom. How can I modify single hex with flash and eeprom to separate files? Or maybe somebody have them converted fos 11.11.0 version?


Mate

you can separate file to Flash and eeprom with Ponyprog

Yu can't use USBasp with ponyprog
With Ponyprog use AVR ISP (STK200/300) parallel port interface


Good luck

[1 6 D]

I have opened "Atmega162_flash_and_eeprom 11.11.0.hex" file in Ponyprog and there are four options:
-Save Device file
-Save Device file as
-Save Program (FLASH) file as
-Save Data (EEPROM) file as

When I click third option and choice *.hex, it looks similiar to hex file which I have read from my cable, same size, same addresses. So I think it's ok.


When I click fourth option and choice *.eep file have 16 kilo and very different then file which I have read from cable (original *.eep have 553 bytes). When I choice *.hex in fourth option it look like original *.eep but it's hex, can I use this hex eeprom file if it looks like original eep file but it's hex?

In attachment "myfirmware.zip" is dump which I have read from my cable. In second zip there is original hex file which have flash and eeprom, other two files I have made with ponyprog, can somebody tell that they are ok?

[mattydr67]

I have opened "Atmega162_flash_and_eeprom 11.11.0.hex" file in Ponyprog and there are four options:
-Save Device file
-Save Device file as
-Save Program (FLASH) file as
-Save Data (EEPROM) file as

When I click third option and choice *.hex, it looks similiar to hex file which I have read from my cable, same size, same addresses. So I think it's ok.


When I click fourth option and choice *.eep file have 16 kilo and very different then file which I have read from cable (original *.eep have 553 bytes). When I choice *.hex in fourth option it look like original *.eep but it's hex, can I use this hex eeprom file if it looks like original eep file but it's hex?

In attachment "myfirmware.zip" is dump which I have read from my cable. In second zip there is original hex file which have flash and eeprom, other two files I have made with ponyprog, can somebody tell that they are ok?

In 99% the Atmega it is protected. So the dump will not be good.
Anyway try it and if it dosen't work conatact me in PM and I will give you the dump for VCDS 11.11.0 in hex or in bin file for PonyProg if you like.
Well from what I know this dump was shared here in this thread but if you don't want to read a lot of stuff you can call me
Good luck

[1 6 D]

I have VCDs cable like in post #3233:
http://www.digital-kaos.co.uk/forums/f152/vag-com-vcds-everything-99750/index216.html#post1695593

Label on wire says VCDS 11.20 EN and I work with VCDS 11.3 Millenium.

I want to update it to 11.11.0, I have converted single hex from this forum to separate hex with flash and separate with eeprom. I use USBasp with Extreme Burner AVR for flashing.

After programming, cable is unregistered when I connect it to car. Maybe it's because of Windows 7 64bit? Serial is for 11.11.0 after programming.

[mattydr67]

I have VCDs cable like in post #3233:
http://www.digital-kaos.co.uk/forums/f152/vag-com-vcds-everything-99750/index216.html#post1695593

Label on wire says VCDS 11.20 EN and I work with VCDS 11.3 Millenium.

I want to update it to 11.11.0, I have converted single hex from this forum to separate hex with flash and separate with eeprom. I use USBasp with Extreme Burner AVR for flashing.

After programming, cable is unregistered when I connect it to car. Maybe it's because of Windows 7 64bit? Serial is for 11.11.0 after programming.

Mate
In your interface you don't need to unsolder the STC, no unsolder anything
Just reflash Atmega
For this you need eeprom.hex and flsah.hex files
And then set the Fuse bits
BUt I suggest you before you reflash you interface to reisntall your OS and install back a fresh VCDS 11.11.0
Then reflash you Atmega, set the right fuse bits and use it. BUT do not use internet connection ever in that computer where you have installed the VCDS softwear.
Check the reflashing pads continuite near the USB pads
Item are like this. ( starting from USB once ) 3, 2,1, 4
(Atmega pins)
Good luck

[1 6 D]

I have converted this 11.11.0 dump to two files and now I have tested it on virtual Windows XP, it works perfect, all time without internet. So I think that clone shouldn't work on 64bit system.

Anytime when I tested 11.11.0 on Win7 x64 I have installed fresh 11.11.0 and cable was unregistered. So I have to use VCDS on virtual XP.

[perotok]

I have converted this 11.11.0 dump to two files and now I have tested it on virtual Windows XP, it works perfect, all time without internet. So I think that clone shouldn't work on 64bit system.

Anytime when I tested 11.11.0 on Win7 x64 I have installed fresh 11.11.0 and cable was unregistered. So I have to use VCDS on virtual XP.

11.11.0 should work on win 7 x64
but you did not install the right drivers

[tjjautos]

Hi Igorm I believe you specialize in making & modifying OBD2 interfaces I was wondering if you can make/modify an interface that can work with all original dealers? software at the same time it might need some software to switch it to specific dealer software? The idea is to have one interface to work with dealer?s software using the same idea as OBD2 passes-though but without being on the net there are a few interfaces that are out there like VCI, M-VCI, X-VCI & VCM ect: that cover a few makes and models what do you think.

[mattydr67]

I have converted this 11.11.0 dump to two files and now I have tested it on virtual Windows XP, it works perfect, all time without internet. So I think that clone shouldn't work on 64bit system.

Anytime when I tested 11.11.0 on Win7 x64 I have installed fresh 11.11.0 and cable was unregistered. So I have to use VCDS on virtual XP.

I don't know what to say about you OS ( WIN 7 64 bit )
But I tested this VCDS 11.11.0 in all kind of OS and allways works
But reflash your tool as I told you. Try it in an Win XP computer ( no internet connection then try it in your Win 7 computer and if now it becomes Unregistred you need to reinstall your OS in your computer.
But before this go back in Win Xp system and Uninstall the VCDS softwear and reinstall it back the test your tool again.
If it will be Full registred after 5 tests you will be sure to reinstall you OS in your computer
Good luck

[1 6 D]

11.11.0 should work on win 7 x64
but you did not install the right drivers
Which driver should I use?

BTW
On virtual XP I have used my cable (with 11.11.0 dump) with VCDS 11.11.4 too. Unofficial VCDS 11.11.4 have updated flash to 1.91 (not to 1.92 like in official version) and I could read coding,measuring blocks,basic setting,adaptations. After looking in modules for 30 minutes serial wasn't unregistered.

Then I have written all new info to decoded clb files from VCDS 11.3. After adding info to this files, my labels folder can be shared to people which want fresh database without flashing cable to work with newer version. All files in "Labels" are lbl, so every version can handle them. lbl are copied from 11.11.4.

[mattydr67]

Which driver should I use?

BTW
On virtual XP I have used my cable (with 11.11.0 dump) with VCDS 11.11.4 too. Unofficial VCDS 11.11.4 have updated flash to 1.91 (not to 1.92 like in official version) and I could read coding,measuring blocks,basic setting,adaptations. After looking in modules for 30 minutes serial wasn't unregistered.

Then I have written all new info to decoded clb files from VCDS 11.3. After adding info to this files, my labels folder can be shared to people which want fresh database without flashing cable to work with newer version. All files in "Labels" are lbl, so every version can handle them. lbl are copied from 11.11.4.
Sir
Your serial which you have in dump for VCDS 11.11.0 it is blacklisted in new versions of VCDS
Starting with VCDS 11.11.1 the serila that you have for VCDS 11.11.0 it is blacklisted and will be erased after 3 times you use it.
About the Labels, you know you can repalce yours with the new once but you cannot new functions from new lables, just the one are common and wans't changed.
The new lables you'll cannot use it.
What do you think that Mr. UWE it is stupid guy?
I belive he's not and he is a smart guy. You can use labels but you'll have a lot of bugs anbd wrong date showing to you.
Do not use your dump with a higher version of VCDS then 11.11.0 and you'll have a good tool. And no internet conection.
Otherwise you'll allways need to reflash it.
For VCDS 11.11.0 you need driver which is installed by the softwear and this one it is higher then the normal driver in all others versions.
You know this new drivers for VCDS 11.11.0 it was replaced in new versions with the old one becasue it creat bugs. VCDS 11.11.0 has a lot of bugs becasue of this driver. If you use old driver with this version you'll have also bugs. I belive that VCDS 10.6.4 it is better then this VCDS 11.11.0
Good luck
Good luck

[liviudiaconu]

Which driver should I use?

BTW
On virtual XP I have used my cable (with 11.11.0 dump) with VCDS 11.11.4 too. Unofficial VCDS 11.11.4 have updated flash to 1.91 (not to 1.92 like in official version) and I could read coding,measuring blocks,basic setting,adaptations. After looking in modules for 30 minutes serial wasn't unregistered.[...]


Share your dump and installer for 11.11.4 unofficial, please.

[mattydr67]

Share your dump and installer for 11.11.4 unofficial, please.

Dear sir or dear frined don't you know to read well
Our mate has dump from this thread. The dump it is for VCDS 11.11.0 and he tried to use it with VCDS 11.11.4
Then he tooks the label files from VCDS 11.11.4 and replaced in VCDS 11.11.0
Do you think there's dump which works with original softwear?
I don't belive so
Maybe next year to show up if there will be a guy with a genuine tool with FTDI BL/BM inside and he wants to make some money extracting this dump.
Otherwise will just using dumps from new tools with FTDI RQ and moded softwears to pass the FTDI ID
Good luck

[dob12]

Share your dump and installer for 11.11.4 unofficial, please.

I can also?

[1 6 D]

I have used proper driver from 11.11.0 installation with it, I have modified "hosts" file to prevent some internet connections too. I have switched off internet before installing fresh VCDS 11.11.0 with new driver, I turned internet on after I have seen information "unregistered" in "About".

liviudiaconu (http://www.digital-kaos.co.uk/forums/members/161166-liviudiaconu/), dob12 (http://www.digital-kaos.co.uk/forums/members/335143-dob12/) , I have posted it here:
http://www.digital-kaos.co.uk/forums/f152/vag-com-vcds-everything-99750/index208.html#post1664042
It uses 1.91 firmware, not 1.92


About copying labels from new to old version, I have swapped for example:
-bits from coding helper in central electric coding for 5K0 modules and everything works,
-adaptation channel about Torque Steer Compensation in Steer Assist
-security access codes,adaptation channels,basic settings about DPF regeneration for 2.0 TDI CR engine
And now everything works in VCDS 11.3. To write this things in older version I have read "template.lbl" first, there is everything how to write/edit lbl file.

Sometimes I use lbl files from german version VCDS if there is no file for module in english version of VCDS, it's very often situation in Audi TDI engines and everything works perfect. I swapped all info to 11.3 because how you write it's most stable version.

[liviudiaconu]

But, if you tell us that with 11.11.0 dumps and 11.11.4 "first version" - aka 11.11.4/1.91 - work fine, what you need for copy new labels in old version?

[1 6 D]

In 11.11.4 with 11.11.0 dump I can only read Coding,no modifications in coding. VCDS say that coding is accepted but it's not changed. After 15 minutes of watching coding helpers in few modules it goes unregistered, but I have new things to put in decoded lbl files,

I connect to module by VCDS, look on Coding Helper, make printscreens if there is something new. Then I write this new descriptions to older lbl files by Notepad and save. I must do that way because from 11.3 version there is not possible to decode clb files.

Here is one of printscreens that I have made by using 11.11.4 with 11.11.0 dump:
http://imageshack.us/a/img850/9287/radioscirocodingbyte3.png (http://imageshack.us/photo/my-images/850/radioscirocodingbyte3.png/)
Now I open lbl file which was decoded clb (from 11.2 version) in Notepad:
http://imageshack.us/a/img690/4266/lbl.png (http://imageshack.us/photo/my-images/690/lbl.png/)

Write there a new line:
LC,03,3,Navigation Preparation (Maps & More / PR-7UE)
and save file.

This line say that in byte 3 bit 3 of coding helper will be this description, if you have updated file in Labels directory. You can write there what you want, I have made by this method lbl files for my native language.

EDIT:
Somebody knows when dump 11.11.0 was released? If it was about may 2012, this dump should work with 11.11.1, 11.11.2 and 11.11.3 because they were released before this date. Probably in VCDS 11.11 is an expiry date, because when I set it a week back 11.11.0 works, but with date after 19.09.2012 it makes cable unregistered, new method for clones?