VVDI PROG

[Samic]

Is vvdi prog able to write flash in hc12dg128 mask 1k50e mpc ? Apparently xprog smok ak300-500 all failure to write flash in this processor ?
Can anyone do me a bdm connections using vvdi prog for cas 1 i think its v1

yes,vvdi prog support write flash for 1k50e/0k50e.you should select the correct type unsecure or secured.by the way,if your chip is damaged means write flash will fail.

[Samic]

The following mistakes does anyone pass the same?
mcu ford fiesta mcu mcu9s12hz256 no read set Frequency UPA OK
memory eeprom 8pin read bad 95320 (FF FF). UPA OK
memory so23p 6 pin error read y write.

please take a clearly photo of the PCB,i will check.maybe the diode effects on this.

[Samic]

Audi A6 ELV (J518) ---2010 not working correctly. Flash read ok but eeprom each reading is different. Please correct it.
Wysłane z iPhone za pomocą Tapatalk

friend,as you said flash read ok but eeprom different,
i want to know,you read the data continuously or read one time then install back to car,then remove read second time.
if continuously read should data same,otherwise the chip is broken.if install to car,eeprom different is normal.

[Samic]

Hello .
Can you make pinouts with vvdi prog for mb91f061bs in suzuki jimny 2015 ?? Please
Need help urgent please
Enviado do meu SM-J320FN atrav?s de Tapatalk

friend,please send me the clearly PCB photo with both sides,thanks so much.

[solitaire]

Samic please add for V850 mcu Data Flash + TAG ID (32kb+32kb). Thanks

[Samic]

Hello mates i need help in reading mb91f061 kia picanto cluster ...






In have seen the carprog a10 pinouts for this proccessor but i need please using vvdi prog to read
Can you please put dots on my photo using colors of vvdi prog cable ..
Thanks mates
Enviado do meu SM-J320FN atrav?s de Tapatalk

friend,also need the clearly photo,you can refer to following information.
MD0 114
DUIN 121
DUOUT 122
RESET 107
GND 114 11 37 52 72 109 116 119 129(any of them ok)
VCC 1 10 36 51 108 128(any of them ok)

[Samic]

Samic please add for V850 mcu Data Flash + TAG ID (32kb+32kb). Thanks

friend,im not sure what do you mean about TAG ID, maybe you mean:read data by other device,the data memory size is 64kb,but VVDI PROG read only 32 kb,right?
if so,you can open VVDI PROG folder----TOOL---load VVDI PROG dump to ‘V850 Dflash format conversion tool’ and coverte.
but for this chip the valid data memory size only 32kb,another added 32kb is invalid data.

[ibratex]

friend,also need the clearly photo,you can refer to following information.
MD0114
DUIN 121
DUOUT122
RESET107
GND11411375272109116119129(any of them ok)
VCC1103651108128(any of them ok)

Samic this is best clear i can do .. after i will prepare the jimny suzuki fotos again

Enviado do meu SM-J320FN atrav?s de Tapatalk

[solitaire]

friend,im not sure what do you mean about TAG ID, maybe you mean:read data by other device,the data memory size is 64kb,but VVDI PROG read only 32 kb,right?
if so,you can open VVDI PROG folder----TOOL---load VVDI PROG dump to ‘V850 Dflash format conversion tool’ and coverte.
but for this chip the valid data memory size only 32kb,another added 32kb is invalid data.

attached d-flash readed with vvdiprog(32kb without ID_TAG) and orange5(64kb with ID_TAG)
you can see this video, about ID TAG
https://www.youtube.com/watch?v=dhhP...ptVyIXg-kR6sH5

[automotrizVIP]

Samic Hello. Could you please lend a hand. With my post 72 # 1071 ... thanks

[eagleone-two]

friend,as you said flash read ok but eeprom different,
i want to know,you read the data continuously or read one time then install back to car,then remove read second time.
if continuously read should data same,otherwise the chip is broken.if install to car,eeprom different is normal.

Hi Samic,

Thanks for your reply.
In this case I read EVL on the table and in the same sesion. No unsolder wires.


Wysłane z iPhone za pomocą Tapatalk

[eagleone-two]

please check the connection,if its secured type need to connect the CLK.

I confirm. Ford Mondeo MK3 not work, read/write.


Wysłane z iPhone za pomocą Tapatalk

[eagleone-two]

please ensure the cut off wires and connection all ok.

All wires 100% correct.


Wysłane z iPhone za pomocą Tapatalk

[Nourd]

i have problem device error driver

[ibratex]

i have problem device error driver

Make Update did you?

Enviado do meu SM-J320FN atrav?s de Tapatalk