>>>>>>>>>>>>>>CONDOR KEYCUTTERS <<<<<<<<<<<<<

[madaxe]

I have recently purchased an XC-mini, and I'm pleasantly surprised by it. Its much better than I was lead to believe!

Has the Renault keycard blade cutting been fixed, or is there a solution by making a custom file? It cuts the opening V incorrectly as mentioned earlier in this thread. I tried making a custom file, but dont know how to correct the opening V part of the key specification.

Also, is the custom file specification available anywhere ? It would encourage alternative software if this were available along with the communication specification over USB.

Thanks.

[sleepyrz]

The cutting for the v0001-v5000 code series for the 10 cut keys hu100 is bad
The tip is wrong and the depths are wrong

Good thing I made a custom key file for the 10 cut

[jose9413]

The cutting for the v0001-v5000 code series for the 10 cut keys hu100 is bad
The tip is wrong and the depths are wrong

Good thing I made a custom key file for the 10 cut

Mind sharing it? ��

[Xhorsesupport]

I have recently purchased an XC-mini, and I'm pleasantly surprised by it. Its much better than I was lead to believe!

Has the Renault keycard blade cutting been fixed, or is there a solution by making a custom file? It cuts the opening V incorrectly as mentioned earlier in this thread. I tried making a custom file, but dont know how to correct the opening V part of the key specification.

Also, is the custom file specification available anywhere ? It would encourage alternative software if this were available along with the communication specification over USB.

Thanks.

It is ready next update.About how to make a custom file,following file for reference,hope that can help you a little.

[madaxe]

Hi, thanks for your reply, but its not clear what you are saying.

"It is ready next update." It can mean the next update is now ready to download, or that the things I've asked for are in the next update, but it is not ready to download. Can you explain which it is please ?

I understand how to make a custom key file, your software is very good in that respect and as I described, I have done this. With my custom key file, the machine cuts the channel almost correctly, however, as I described the tip of the key where the opening V is cut, is not cut correctly. It has been described with photos in this thread earlier from post #399, though I only just read there is a universal copy tool, I'll try that but doesnt help if I need to cut the key to a lock I decoded. So needs to be fixed. Maybe have a couple of options in the software for how wide the V at the tip needs to be ?

And regarding the custom key file specification and the communication over USB ? Any chance that will be available to developers and interested parties soon ? That would certainly help people develop software compatible with your machine.

Thanks

[Jobeso66]

Were you able to find it?


Sent from my iPhone using Tapatalk

Yes I have. Thank you


Sent from my iPhone using Tapatalk

[BRMTDI]

Need some help tried to cut a key for 2013 VW CC also Passat 6B Believe is same key.

All keys are only plastic, my issues was everytime I have my machine xc007 trace key, the trace bit would snap, I never Seen that before, I snapped three trace bits in row.

Is there issue with machine? Or somejing xhorse knows about?

I did last big update, not sure if more updates where made since then.

Just trying to find out if anyone else’s experienced this issue.

[kleidaras]

Machine work with electric contact. On plastic key not have electric contact and tracer brake. All machines work like this.

Στάλθηκε από το F3311 μου χρησιμοποιώντας Tapatalk

[sleepyrz]

Need some help tried to cut a key for 2013 VW CC also Passat 6B Believe is same key.

All keys are only plastic, my issues was everytime I have my machine xc007 trace key, the trace bit would snap, I never Seen that before, I snapped three trace bits in row.

Is there issue with machine? Or somejing xhorse knows about?

I did last big update, not sure if more updates where made since then.

Just trying to find out if anyone else’s experienced this issue.

Decode by eye if you have old key or by lishi if no key

Insert hu66 metal key

Input code you got

Start the machine so it calibrates on the metal key and just when it is about to start cutting

Press pause and pull out metal key blade and swap in plastic blade

press pause again to continue

This is how I do it

The problem with the machine in this case is you not knowing enough about how it works

[Xhorsesupport]

Hi, thanks for your reply, but its not clear what you are saying.

"It is ready next update." It can mean the next update is now ready to download, or that the things I've asked for are in the next update, but it is not ready to download. Can you explain which it is please ?

I understand how to make a custom key file, your software is very good in that respect and as I described, I have done this. With my custom key file, the machine cuts the channel almost correctly, however, as I described the tip of the key where the opening V is cut, is not cut correctly. It has been described with photos in this thread earlier from post #399, though I only just read there is a universal copy tool, I'll try that but doesnt help if I need to cut the key to a lock I decoded. So needs to be fixed. Maybe have a couple of options in the software for how wide the V at the tip needs to be ?

And regarding the custom key file specification and the communication over USB ? Any chance that will be available to developers and interested parties soon ? That would certainly help people develop software compatible with your machine.

Thanks

The "Renault" opening V cut incorrect,engineer has revised it and will upload the modification soon.I'll let you know when the revise is uploaded,at that time you just need to update the condor.Any problem please feel free to contact with me,thank you.

[gokart]

Decode by eye if you have old key or by lishi if no key

Insert hu66 metal key

Input code you got

Start the machine so it calibrates on the metal key and just when it is about to start cutting

Press pause and pull out metal key blade and swap in plastic blade

press pause again to continue

This is how I do it

The problem with the machine in this case is you not knowing enough about how it works

It is unnecessary to insert metal HU66. Just insert plastic HU66 to cut it.

[autoTkey]

It is unnecessary to insert metal HU66. Just insert plastic HU66 to cut it.

If you want to brake your sensing probe or the cutter - yes, you can do it without putting the metal key first...

[gokart]

If you want to brake your sensing probe or the cutter - yes, you can do it without putting the metal key first...

...nope, it can't damage anything in case of HU66. If Condor doesn't touch the key blade before cutting you can put directly the plastic key.

[dmp]

...nope, it can't damage anything in case of HU66. If Condor doesn't touch the key blade before cutting you can put directly the plastic key.

Cutter touches the top of the key for reference height on a hu66

Sent from my SM-G930W8 using Tapatalk

[gokart]

Cutter touches the top of the key for reference height on a hu66

Sent from my SM-G930W8 using Tapatalk

It doesn't check the height of the HU66 key. The first video what I found about it: https://www.youtube.com/watch?v=lSGS70bFEBo