>>>>>>>>>>>>>>CONDOR KEYCUTTERS <<<<<<<<<<<<<

**MaxMin** · 16th March, 2017, 06:17 PM

it is have difference with this two blade?
i cut this BE key blade with xc-mini but not open door,i see condor not 100% cuting BE blade
in picture ori nec key and be key
with NEC to NEC blade i not have problem, all is ok

be+necv57.JPG

**sleepyrz** · 16th March, 2017, 06:30 PM

milling looks shorter on be key

is the key going in the lock all the way???

take door lock out of door and check

long t20 or t25 is needed

**dmp** · 16th March, 2017, 06:35 PM

Originally Posted by MaxMin

it is have difference with this two blade?
i cut this BE key blade with xc-mini but not open door,i see condor not 100% cuting BE blade
in picture ori nec key and be key
with NEC to NEC blade i not have problem, all is ok

be+necv57.JPG

Cut on hu64-3. Check blade size and input cuts manually. The angle from the first cut to the tip is different based on the length. Will work in the lock

Sent from my SM-G930W8 using Tapatalk

**Romney1** · 16th March, 2017, 07:58 PM

Hi
can anyone shed any light on cutting a silca EU21p to key number it is used on a motorhome
Is this possible on my condor tool or is this not classed as an automotive key
cheers in advance

**rob h** · 16th March, 2017, 08:28 PM

Originally Posted by Romney1

Hi
can anyone shed any light on cutting a silca EU21p to key number it is used on a motorhome
Is this possible on my condor tool or is this not classed as an automotive key
cheers in advance

Is it a dimple key: then no.
Otherwise you can creat a custom key file.

**Romney1** · 16th March, 2017, 08:48 PM

No its not a dimple . Milling style im not sure how to create a file as i dont have the measurements of
the depths as all i have is a key number and instacode doesnt list any thing

**rob h** · 17th March, 2017, 12:34 AM

Here is your EU21P file.

Use the customkeytool.
Place this custom Eurolock file in the customkeyfolder.
Open the customkeytool.
Import the custom Eurolock file.
Then synchronize with your Condor.

You should check these measurements.
B: lenght from tip to shoulder 20mm
D: key blade thicknes 3mm
E: internal width 1.2mm

If these are incorrect. Right click on the custom-u in the define key data list.
And simply edit these.Eurolocks.rar

**AndyCZ** · 17th March, 2017, 11:02 AM

NE78 not cut completely

ne78.jpg

**rob h** · 17th March, 2017, 12:38 PM

Originally Posted by AndyCZ

NE78 not cut completely

ne78.jpg

If you look close at the shoulder, you see the little differences.
You did not place or calibrate correct.
Check setting, if cutter diameter is correct!
The cutter missed your key tip!

**AndyCZ** · 17th March, 2017, 12:56 PM

Originally Posted by rob h

If you look close at the shoulder, you see the little differences.
You did not place or calibrate correct.
Check setting, if cutter diameter is correct!
The cutter missed your key tip!

both keys tight to that shoulder as machine show on picture

ne78.jpg

**rob h** · 17th March, 2017, 01:14 PM

Did you measure the tip to shoulder lenght?
The cuts need to be further back to the shoulder.
If all fails, start the cutting, and pause after the calibration.
Then place the about 1 mm towards tip.

**AndyCZ** · 17th March, 2017, 03:01 PM

Originally Posted by rob h

Did you measure the tip to shoulder lenght?
The cuts need to be further back to the shoulder.
If all fails, start the cutting, and pause after the calibration.
Then place the about 1 mm towards tip.

Rob h you will not fix the blade in 1-2mm edge

20170317_145528.jpg

**rob h** · 17th March, 2017, 03:31 PM

I see, you have a mini Condor.
The clamp is different from the master condor.
If the settings on your machine are correct, and you have choosen the correct clamp and cutter.
Then it could be the key file.
There is a keycutsomtool for the mini condor.
You could create your own key file and load it by usb.

It is good to know how to use this customkeytool. Takes about 5min max.
There are probable a few more of these keys that give you troubles.
Or they dont excist yet.

And waiting for updates, is not a option for me.

Originally Posted by AndyCZ

Rob h you will not fix the blade in 1-2mm edge

20170317_145528.jpg

**dmp** · 17th March, 2017, 03:33 PM

Has anybody else had a problem loading the custom key files? I have the big condor and used the same software to update the software about a year ago, it connects to the machine and says they were able to synchronize but I can't find my custom key files anywhere.

Should I try to do it with a different computer or do the files not end up with the manufacturer I selected?

Sent from my SM-G930W8 using Tapatalk

**rob h** · 17th March, 2017, 04:19 PM

Hello Dmp,

My Condor is still giving me the screen calibration problems.
So i can not test this right now. But i have loaded files before.
My machine runs on the latest software, that might be neccecary.

I have recieved the mini condor 1.1.0 custom key tool from support.
Butt have troubles uploading it for you guys. I will try that later on the mini condor thread.